<div dir="ltr"><div class="gmail_extra"><br><div class="gmail_quote">On Fri, Aug 28, 2015 at 4:52 PM, Stephen Dowdy <span dir="ltr"><<a href="mailto:sdowdy@ucar.edu" target="_blank">sdowdy@ucar.edu</a>></span> wrote:<br><blockquote class="gmail_quote" style="margin:0px 0px 0px 0.8ex;border-left:1px solid rgb(204,204,204);padding-left:1ex"><div class="gmail_default" style="font-family:monospace,monospace">The system DOES boot successfully, after a long pause (as expected)...<br></div><div class="gmail_default" style="font-family:monospace,monospace">but
it DOES boot. I am going to reboot a few more times with this setup
(test1) to make sure it's consistent, and then try installing the
'test0' pair of .debs <br>and get back to you, but i wanted to confirm that at least on initial glance, the 'test1' .debs solve my problem.<div class=""><div id=":gb" class="" tabindex="0"></div></div></div></blockquote></div><br><div class="gmail_default" style="font-family:monospace,monospace">Michael,</div><br><div class="gmail_default" style="font-family:monospace,monospace">'test0' does NOT boot -- same symptoms as stock system. (stacktrace thrown about 30 seconds from boot)<br><br></div><div class="gmail_default" style="font-family:monospace,monospace">i rebooted into PXE FAI startup, /target-mounted the system's disks, and redid the 'dpkg -i' for the 'test1' debs.<br><br></div><div class="gmail_default" style="font-family:monospace,monospace">I've rebooted successfully into 'test1' eight times now. FWIW, the LSI SAS 6/iR responds at about 32 seconds into the boot (just past the arbitrary/too-short 30 second default imposed upstream)<br><br>[ 1.687440] ioc0: LSISAS1068E B3: Capabilities={Initiator}<br>[ 1.923382] tsc: Refined TSC clocksource calibration: 2666.666 MHz<br>[ 2.923839] Switched to clocksource tsc<br>[ 4.003537] floppy0: no floppy controllers found<br>[ 32.500534] scsi6 : ioc0: LSISAS1068E B3, FwRev=00192f00h, Ports=1, MaxQ=266, IRQ=28<br>[ 32.536560] mptsas: ioc0: attaching ssp device: fw_channel 0, fw_id 8, phy 0, sas_addr 0x5000cca0091a71e5<br>[ 32.538335] scsi 6:0:0:0: Direct-Access HITACHI HUS154545VLS300 D590 PQ: 0 ANSI: 5<br>[ 32.543522] scsi 6:0:0:0: Attached scsi generic sg2 type 0<br>[ 32.545641] mptsas: ioc0: attaching ssp device: fw_channel 0, fw_id 1, phy 1, sas_addr 0x5000cca0091692bd<br>[ 32.547383] scsi 6:0:1:0: Direct-Access HITACHI HUS154545VLS300 D590 PQ: 0 ANSI: 5<br>[ 32.552451] scsi 6:0:1:0: Attached scsi generic sg3 type 0<br>[ 32.554726] mptsas: ioc0: attaching raid volume, channel 1, id 0<br>[ 32.555715] scsi 6:1:0:0: Direct-Access Dell VIRTUAL DISK 1028 PQ: 0 ANSI: 5<br>[ 32.563821] scsi 6:1:0:0: Attached scsi generic sg4 type 0<br>[ 32.612706] sd 6:1:0:0: [sda] 877920256 512-byte logical blocks: (449 GB/418 GiB)<br>[ 32.613456] sd 6:1:0:0: [sda] Write Protect is off<br>[ 32.613563] sd 6:1:0:0: [sda] Mode Sense: 03 00 00 08<br>[ 32.613757] sd 6:1:0:0: [sda] No Caching mode page found<br>[ 32.613865] sd 6:1:0:0: [sda] Assuming drive cache: write through<br>[ 32.648782] sda: sda1 sda2 sda3 sda4 < sda5 sda6 sda7 sda8 sda9 sda10 ><br><br><br></div><div class="gmail_default" style="font-family:monospace,monospace">Thanks for your assistance here -- i really hope we can get this into Jessie 8.2!<br></div><br>--<div class="gmail_default" style="font-family:monospace,monospace;display:inline">stephen</div><br><br clear="all"><br>-- <br><div class="gmail_signature">Stephen Dowdy - Systems Administrator - NCAR/RAL<br>303.497.2869 - <a href="mailto:sdowdy@ucar.edu" target="_blank">sdowdy@ucar.edu</a> - <a href="http://www.ral.ucar.edu/~sdowdy/" target="_blank">http://www.ral.ucar.edu/~sdowdy/</a><br><br><br></div>
</div></div>