[debian-edu-commits] [Debian Wiki] Update of "DebianEdu/Documentation/ITIL/ExtraConfiguration" by WolfgangSchweer

[Debian Wiki]

Dear Wiki user,

You have subscribed to a wiki page or wiki category on "Debian Wiki" for change notification.

The "DebianEdu/Documentation/ITIL/ExtraConfiguration" page has been changed by WolfgangSchweer:
https://wiki.debian.org/DebianEdu/Documentation/ITIL/ExtraConfiguration?action=diff&rev1=23&rev2=24

Comment:
codeblocks: add whitespace to avoid splitting upon docbook export

  
  {{{
  a.   Coyote floppy builder script v2.9
- 
+  
      Please choose the desired capacity for the created floppy:
      1) 1.44MB (Safest and most reliable but may lack space needed for
             some options)
      2) 1.68MB (Good reliability with extra space) - recommended
      3) 1.72MB (Most space but may not work on all systems or with all
             diskettes)
- 
+  
      Enter selection:2
  }}}
  The recommended choice is «1.68MB»
  
  {{{
  b.   Please select the type of Internet connection that your system uses.
- 
+  
      1) Standard Ethernet Connection
      2) PPP over Ethernet Connection
      3) PPP Dialup Connection\n\nEnter Selection:
@@ -79, +79 @@

  c.   Configuring system for Ethernet based Internet connection.
      By default, Coyote uses the following settings for the local network
      interface:
- 
+  
      IP Address: 192.168.0.1
      Netmask:    255.255.255.0
      Broadcast:  192.168.0.255
      Network:    192.168.0.0
- 
+  
      Would you like to change these settings? [Y/N]: y
      Enter local IP Address [192.168.0.1]: 10.0.2.1
      Enter local Netmask [255.255.255.0]: 255.255.254.0
@@ -100, +100 @@

      Netmask:    255.255.254.0
      Broadcast:  10.0.3.255
      Network:    10.0.2.0
- 
+  
  e.   Does your Internet connection get its IP via DHCP? [y/n]:
  }}}
  Answer yes(y) or no(n) in accordance with what the network configuration is.
@@ -138, +138 @@

  {{{
  j. You now need to specify the module name and parameters for your
    network cards.
- 
+  
    If you are using PCI or EISA cards, leave the IO and IRQ lines
    blank.
- 
+  
    Enter the module name for you local network card:
  }}}
  This is the tricky part. Knowing which module to use for network cards is sometimes difficult. See [[#!ExtraConfiguration--clmodules|Section 3.12]] to get an overview of the available modules. Remember to not use .o at the end of the module name. Use only "first name" of the module.
@@ -165, +165 @@

  {{{
      Checking module deps for (wrong,bad)...
      Copying module: drivers/wrong.o
- 
+  
      Unable to copy module (drivers/wrong.o): No such file or directory
  }}}
  Be sure you get something like this instead:
@@ -540, +540 @@

  
  {{{
  Configuring system for Ethernet based Internet connection
- 
- 
+  
+  
  By default, Coyote uses the following settings for the local network
  interface:
- 
+  
  IP Address: 192.168.0.1
  Netmask:    255.255.255.0
  Broadcast:  192.168.0.255
  Network:    192.168.0.0
- 
+  
  Would you like to change these settings? [Y/N]: n
  }}}
  then you should use the address 192.168.0.1 instead of 10.0.2.1 when logging into the Coyote Linux web administration. See [[#!ExtraConfiguration--clgui|Section 3.7]] and