[Nut-upsdev] new ups for database?

[spamwhole at gmail.com]

Hi, 

I have the same device, a F6H500ukUNV, it has both RS-232 and USB. 

url:
http://catalog.belkin.com/IWCatProductPage.process?Product_Id=201050 


The details I have from my system are below.  If you would like further 
informatinon, or a more verbose lsusb please let me know. 

thanks 

Rob 

dmesg:
hiddev96: USB HID v1.00 Device [MEC MEC0002] on usb-0000:05:06.1-2 

lsusb:
Bus 005 Device 004: ID 0001:0000 Fry's Electronics 

cat /proc/bus/usb/device:
T:  Bus=05 Lev=01 Prnt=01 Port=01 Cnt=01 Dev#=  4 Spd=1.5 MxCh= 0
D:  Ver= 1.00 Cls=00(>ifc ) Sub=00 Prot=00 MxPS= 8 #Cfgs=  1
P:  Vendor=0001 ProdID=0000 Rev= 1.00
S:  Manufacturer=MEC
S:  Product=MEC0002
C:* #Ifs= 1 Cfg#= 1 Atr=80 MxPwr=100mA
I:  If#= 0 Alt= 0 #EPs= 1 Cls=03(HID  ) Sub=00 Prot=00 Driver=usbhid
E:  Ad=81(I) Atr=03(Int.) MxPS=   8 Ivl=10ms 

>
>Hi Dave, 
>
>nothing in the outputs you sent looks like any Belkin device is
>present. Are you sure it is attached to your computer? You should have
>something like this in /proc/bus/usb/devices: 
>
>T:  Bus=04 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#=  3 Spd=1.5 MxCh= 0
>D:  Ver= 1.10 Cls=00(>ifc ) Sub=00 Prot=00 MxPS= 8 #Cfgs=  1
>P:  Vendor=050d ProdID=0980 Rev= 0.06
>S:  Manufacturer=       
>S:  Product=UPS
>C:* #Ifs= 1 Cfg#= 1 Atr=c0 MxPwr= 20mA
>I:  If#= 0 Alt= 0 #EPs= 1 Cls=03(HID  ) Sub=00 Prot=00 Driver=usbhid
>E:  Ad=81(I) Atr=03(Int.) MxPS=   8 Ivl=248ms 
>
>Note "Vendor=050d", which is Belkin's vendor ID.  
>
>The output from newhidups does not show a 050d/XXXX device either.  
>
>-- Peter 
>
>meherenow at darkglobe.org wrote:
>> 
>> I have a Belkin F6H500ukUNV ups that I am attempting to get working =20
>> under nut, however it
>> does not appear to be detected by nut, I'm assuming that I need to =20
>> feed some information
>> back to you guys to get it included in the database somwhere. 
>> 
>> I've included (what I can think might be) the relivant outputs. Please >=20
>> let me know if you
>> require anything else. 
>> 
>> dmesg output
>> /sbin/newhidsups output
>> ll /dev/usb*
>> cat /proc/bus/usb/devices 
>> 
>> p.s. I tried chmodding /dev/usb<blah> 777 just incase it was a =20
>> permissions problem, but
>> that didn't help either. 
>> 
>> Many thanks. 
>> 
>> ###########################################################
>> dmesg output when connecting the ups 
>> 
>> usb 2-1: new low speed USB device using uhci_hcd and address 2
>> PM: Adding info for usb:2-1
>> PM: Adding info for No Bus:usbdev2.2_ep00
>> usb 2-1: configuration #1 chosen from 1 choice
>> PM: Adding info for usb:2-1:1.0
>> hiddev96: USB HID v1.00 Device [MEC MEC0002] on usb-0000:00:10.1-1
>> PM: Adding info for No Bus:usbdev2.2_ep81