[Nut-upsdev] Fwd: [HCL] Novex NUPS-650 supported by blazer_usb
программист некто
programmer11180 at programist.ru
Fri Nov 22 11:30:46 UTC 2013
Novex NUPS-650
USB information
$ lsusb -s 002:027 -v
Bus 002 Device 027: ID 0001:0000 Fry's Electronics
Device Descriptor:
bLength 18
bDescriptorType 1
bcdUSB 1.00
bDeviceClass 0 (Defined at Interface level)
bDeviceSubClass 0
bDeviceProtocol 0
bMaxPacketSize0 8
idVendor 0x0001 Fry's Electronics
idProduct 0x0000
bcdDevice 1.00
iManufacturer 1
iProduct 2
iSerial 0
bNumConfigurations 1
Configuration Descriptor:
bLength 9
bDescriptorType 2
wTotalLength 34
bNumInterfaces 1
bConfigurationValue 1
iConfiguration 0
bmAttributes 0x80
(Bus Powered)
MaxPower 100mA
Interface Descriptor:
bLength 9
bDescriptorType 4
bInterfaceNumber 0
bAlternateSetting 0
bNumEndpoints 1
bInterfaceClass 3 Human Interface Device
bInterfaceSubClass 0 No Subclass
bInterfaceProtocol 0 None
iInterface 0
HID Device Descriptor:
bLength 9
bDescriptorType 33
bcdHID 1.00
bCountryCode 0 Not supported
bNumDescriptors 1
bDescriptorType 34 Report
wDescriptorLength 624
Report Descriptors:
** UNAVAILABLE **
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x81 EP 1 IN
bmAttributes 3
Transfer Type Interrupt
Synch Type None
Usage Type Data
wMaxPacketSize 0x0008 1x 8 bytes
bInterval 10
Device Status: 0x0000
(Bus Powered)
upsc information
$ upsc novex at localhost:3650
battery.charge: 100
battery.voltage: 13.00
battery.voltage.high: 12.70
battery.voltage.low: 11.2
battery.voltage.nominal: 11.5
device.mfr: NOVEX
device.model: UPS650
device.type: ups
driver.name: blazer_usb
driver.parameter.pollinterval: 2
driver.parameter.port: auto
driver.parameter.protocol: megatec
driver.version: 2.6.5
driver.version.internal: 0.09
input.current.nominal: 4.0
input.frequency: 49.8
input.frequency.nominal: 50
input.voltage: 223.0
input.voltage.fault: 165.0
input.voltage.nominal: 220
output.voltage: 223.0
ups.alarm: Shutdown imminent!
ups.beeper.status: disabled
ups.delay.shutdown: 30
ups.delay.start: 180
ups.firmware: VER3.10C
ups.load: 0
ups.mfr: NOVEX
ups.model: UPS650
ups.productid: 0000
ups.status: ALARM OL FSD
ups.temperature: 0.0
ups.type: offline / line interactive
ups.vendorid: 0001
shutdown sequence: not tested. Driver randomly fails to start. For more details see bug
http://bugs.debian.org/cgi-bin/bugreport.cgi?bug=694717
Online description (I found several pages only on Russian language)
http://komp.1k.by/periphery-ups/novex/Novex_NUPS_650-130052.html
Type interactive
Output power
Full 650 VA
Active 390 W
Operation time
Full load 8 min
Output Waveform sine wave
Voltage
Input 1-phase
Output 1-phase
Number of output power
Common 1
UPS 1
Type IEC 320 C13 (computer)
Input voltage
Minimum 165 V
Maximum 275 V
Functions Novex NUPS-650
Display information LCD Screen
Audible alarm Yes
By-pass
Manual -
Automatic -
Interfaces Novex NUPS-650
USB Yes
RS-232 -
Ethernet 10/100 -
Slot for optional interfaces -
Dry contacts -
Support for SNMP -
Protecting Novex NUPS-650
Protection from high-voltage pulses Yes
Noise Filtering Yes
Protection against short-circuit Yes
Phone line protection Yes
Protecting the local network Yes
Protecting the antenna cable -
Nutrition Novex NUPS-650
Charging time 8 h
Replacing the batteries Yes
Hot swappable batteries -
Connection of additional battery -
Additional information Novex NUPS-650
Height 160 mm
Width 90 mm
Depth 340 mm
Weight 6.5 kg
Color black
upscmd information
test.battery.start not work - upscmd says 'OK', but UPS not start the test.
test.battery.start.deep works not as it was expected - UPS switches to battery two times across 1 second and all.
This two commands works in Windows in the Upsilon 2000 in the same way. May be this is a UPS issue.
More information about the Nut-upsdev
mailing list