[Nut-upsuser] Plexus UPS 1000V - megatec_usb

[Jason Pearce]

Hi,

Just purchashed this UPS.

The megatec_usb driver appears to be communicating with the UPS - 
however, the ups.status field always states "off"

/usr/local/ups/bin/megatec_usb -a plexus -DD
Network UPS Tools 2.2.1 - Megatec protocol driver 1.5.9 [megatec_usb]
Carlos Rodrigues (c) 2003-2007

Serial-over-USB transport layer for Megatec protocol driver [megatec_usb]
Andrey Lelikov (c) 2006, Alexander Gordeev (c) 2006-2007, Jon Gough (c) 2007

debug level is '2'
Checking device (0000/0000) (002/001)
- VendorID: 0000
- ProductID: 0000
- Manufacturer: unknown
- Product: unknown
- Serial Number: unknown
- Bus: 002
Trying to match device
Device does not match - skipping
Checking device (116F/C108) (001/003)
- VendorID: 116f
- ProductID: c108
- Manufacturer: unknown
- Product: unknown
- Serial Number: unknown
- Bus: 001
Trying to match device
Device does not match - skipping
Checking device (0000/0000) (001/001)
- VendorID: 0000
- ProductID: 0000
- Manufacturer: unknown
- Product: unknown
- Serial Number: unknown
- Bus: 001
Trying to match device
Device does not match - skipping
Checking device (0001/0000) (001/002)
- VendorID: 0001
- ProductID: 0000
- Manufacturer: unknown
- Product: unknown
- Serial Number: unknown
- Bus: 001
Trying to match device
Device matches
Starting UPS detection process...
Asking for UPS status [Q1]...
Q1 => OK [(234.0 165.0 234.0 000 49.8 27.3 00.0 00001010]
Asking for UPS status [Q1]...
Q1 => OK [(231.0 165.0 231.0 000 50.0 27.3 00.0 00001010]
Asking for UPS status [Q1]...
Q1 => OK [(231.0 165.0 231.0 000 50.0 27.3 00.0 00001010]
Asking for UPS status [Q1]...
Q1 => OK [(231.0 165.0 231.0 000 50.0 27.3 00.0 00001010]
Asking for UPS status [Q1]...
Q1 => OK [(231.0 165.0 231.0 000 50.0 27.3 00.0 00001010]
0 out of 5 detection attempts failed (minimum failures: 2).
Asking for UPS information [I]...
I => OK [#                UPS1000V   VER1.04   ]
Megatec protocol UPS detected [ UPS1000V VER1.04].
Asking for UPS power ratings [F]...
F => OK [#230.0 005 23.50 50.0]
23.5V battery, interval [21.3V, 27.1V].
Done setting up the UPS.
Asking for UPS status [Q1]...
Q1 => OK [(231.0 165.0 231.0 000 50.0 27.3 00.0 00001010]
Calculated battery charge: 100.0%
dstate_init: sock /var/state/ups/megatec_usb-plexus open on fd 5
Asking for UPS status [Q1]...
Q1 => OK [(231.0 165.0 231.0 000 49.8 27.3 00.0 00001010]
Calculated battery charge: 100.0%
Asking for UPS status [Q1]...
Q1 => OK [(231.0 165.0 231.0 000 50.0 27.3 00.0 00001010]
Calculated battery charge: 100.0%
Asking for UPS status [Q1]...
Q1 => OK [(231.0 165.0 231.0 000 49.8 27.3 00.0 00001010]
Calculated battery charge: 100.0%
Asking for UPS status [Q1]...
Q1 => OK [(231.0 165.0 231.0 000 50.0 27.3 00.0 00001010]
Calculated battery charge: 100.0%
Asking for UPS status [Q1]...
Q1 => OK [(229.0 165.0 229.0 000 50.0 27.3 00.0 00001010]
Calculated battery charge: 100.0%

/usr/local/ups/bin/upsc plexus at localhost
battery.charge: 100.0
battery.voltage: 27.30
battery.voltage.nominal: 23.5
driver.name: megatec_usb
driver.parameter.pollinterval: 2
driver.parameter.port: /dev/hiddev0
driver.version: 2.2.1
driver.version.internal: 1.5.9
input.frequency: 50.0
input.voltage: 229.0
input.voltage.fault: 165.0
input.voltage.maximum: 234.0
input.voltage.minimum: 229.0
output.voltage: 229.0
output.voltage.nominal: 230.0
ups.beeper.status: disabled
ups.delay.shutdown: 0
ups.delay.start: 2
ups.load: 0.0
ups.mfr:
ups.model: UPS1000V VER1.04
ups.serial: unknown
ups.status: OFF
ups.temperature: 0.0


Bus 001 Device 002: ID 0001:0000 Fry's Electronics
Device Descriptor:
  bLength                18
  bDescriptorType         1
  bcdUSB               1.00
  bDeviceClass            0 (Defined at Interface level)
  bDeviceSubClass         0
  bDeviceProtocol         0
  bMaxPacketSize0         8
  idVendor           0x0001 Fry's Electronics
  idProduct          0x0000
  bcdDevice            1.00
  iManufacturer           1
  iProduct                2
  iSerial                 0
  bNumConfigurations      1
  Configuration Descriptor:
    bLength                 9
    bDescriptorType         2
    wTotalLength           34
    bNumInterfaces          1
    bConfigurationValue     1
    iConfiguration          0
    bmAttributes         0x80
    MaxPower              100mA
    Interface Descriptor:
      bLength                 9
      bDescriptorType         4
      bInterfaceNumber        0
      bAlternateSetting       0
      bNumEndpoints           1
      bInterfaceClass         3 Human Interface Devices
      bInterfaceSubClass      0 No Subclass
      bInterfaceProtocol      0 None
      iInterface              0
        HID Device Descriptor:
          bLength                 9
          bDescriptorType        33
          bcdHID               1.00
          bCountryCode            0 Not supported
          bNumDescriptors         1
          bDescriptorType        34 Report
          wDescriptorLength     624
         Report Descriptors:
           ** UNAVAILABLE **
      Endpoint Descriptor:
        bLength                 7
        bDescriptorType         5
        bEndpointAddress     0x81  EP 1 IN
        bmAttributes            3
          Transfer Type            Interrupt
          Synch Type               None
          Usage Type               Data
        wMaxPacketSize     0x0008  1x 8 bytes
        bInterval              10


Any ideas ?

Regards,

Jason