[Nut-upsuser] Plexus UPS 1000V - megatec_usb

[Jason Pearce]

Hi,

Back in December I posted this request :

http://lists.alioth.debian.org/pipermail/nut-upsuser/2007-December/003565.ht
ml


I have now tried version 2.2.2, which appears to give a slightly better
ups.status of 
"OL OFF"

Any further ideas - the UPS is on and connected to the load.

Regards,
Jason

/usr/local/ups/bin/megatec_usb -a plexus -DD

Network UPS Tools 2.2.2 - Megatec protocol driver 1.5.14 [megatec_usb]
Carlos Rodrigues (c) 2003-2008

Serial-over-USB transport layer for Megatec protocol driver [megatec_usb]
Andrey Lelikov (c) 2006, Alexander Gordeev (c) 2006-2007, Jon Gough (c) 2007

debug level is '2'
Checking device (0000/0000) (001/001)
- VendorID: 0000
- ProductID: 0000
- Manufacturer: unknown
- Product: unknown
- Serial Number: unknown
- Bus: 001
Trying to match device
Device does not match - skipping
Checking device (116F/C108) (002/003)
- VendorID: 116f
- ProductID: c108
- Manufacturer: unknown
- Product: unknown
- Serial Number: unknown
- Bus: 002
Trying to match device
Device does not match - skipping
Checking device (0001/0000) (002/002)
- VendorID: 0001
- ProductID: 0000
- Manufacturer: unknown
- Product: unknown
- Serial Number: unknown
- Bus: 002
Trying to match device
Device matches
failed to claim USB device, trying 2 more time(s)...
detaching kernel driver from USB device...
trying again to claim USB device...
Starting UPS detection process...
Asking for UPS status [Q1]...
Q1 => OK [(231.0 165.0 231.0 000 50.0 27.3 00.0 00001010]
Asking for UPS status [Q1]...
Q1 => OK [(234.0 165.0 234.0 000 50.0 27.3 00.0 00001010]
Asking for UPS status [Q1]...
Q1 => OK [(234.0 165.0 234.0 000 50.0 27.3 00.0 00001010]
Asking for UPS status [Q1]...
Q1 => OK [(234.0 165.0 234.0 000 50.0 27.3 00.0 00001010]
Asking for UPS status [Q1]...
Q1 => OK [(234.0 165.0 234.0 000 50.0 27.3 00.0 00001010]
0 out of 5 detection attempts failed (minimum failures: 2).
Cancelling any pending shutdown or battery test.
Asking for UPS information [I]...
I => OK [#                UPS1000V   VER1.04   ]
Megatec protocol UPS detected [ UPS1000V VER1.04].
Parameter [ignoreoff]: [false]
Asking for UPS power ratings [F]...
F => OK [#230.0 005 23.50 50.0]
23.5V battery, interval [21.3V, 27.1V].
Done setting up the UPS.
Asking for UPS status [Q1]...
Q1 => OK [(234.0 165.0 234.0 000 50.0 27.3 00.0 00001010]
Calculated battery charge: 100.0%
dstate_init: sock /var/state/ups/megatec_usb-plexus open on fd 5
Asking for UPS status [Q1]...
Q1 => OK [(234.0 165.0 234.0 000 50.0 27.3 00.0 00001010]
Calculated battery charge: 100.0%
Asking for UPS status [Q1]...
Q1 => OK [(234.0 165.0 234.0 000 50.0 27.3 00.0 00001010]
Calculated battery charge: 100.0%
Asking for UPS status [Q1]...
Q1 => OK [(234.0 165.0 234.0 000 50.0 27.3 00.0 00001010]
Calculated battery charge: 100.0%
Asking for UPS status [Q1]...
Q1 => OK [(234.0 165.0 234.0 000 49.8 27.3 00.0 00001010]
Calculated battery charge: 100.0%
Asking for UPS status [Q1]...
Q1 => OK [(234.0 165.0 234.0 000 50.0 27.3 00.0 00001010]
Calculated battery charge: 100.0%
Signal 2: exiting


upsc plexus
battery.charge: 100.0
battery.voltage: 27.30
battery.voltage.nominal: 23.5
driver.name: megatec_usb
driver.parameter.pollinterval: 2
driver.parameter.port: auto
driver.version: 2.2.2
driver.version.internal: 1.5.14
input.frequency: 50.0
input.frequency.nominal: 50.0
input.voltage: 234.0
input.voltage.fault: 165.0
input.voltage.maximum: 243.0
input.voltage.minimum: 226.0
input.voltage.nominal: 230.0
output.voltage: 234.0
ups.beeper.status: disabled
ups.delay.shutdown: 0
ups.delay.start: 2
ups.load: 0.0
ups.mfr:
ups.model: UPS1000V VER1.04
ups.serial: unknown
ups.status: OL OFF
ups.type: standby