[Nut-upsuser] [HCL]

[Danilo Godec]

Device manufacturer: GE Digital Energy
(http://www.gedigitalenergy.com/powerquality/catalog/rackmountnet.htm)
Device name: GE EP6000R
(http://www.gedigitalenergy.com/powerquality/catalog/rackmountnet.htm)

*upsc:*

    * battery.voltage: 272.40
    * battery.voltage.nominal: 240.0
    * beeper.status: disabled
    * device.type: ups
    * driver.name: blazer_usb
    * driver.parameter.bus: 004
    * driver.parameter.pollinterval: 2
    * driver.parameter.port: auto
    * driver.version: 2.6.0
    * driver.version.internal: 0.03
    * input.current.nominal: 27.0
    * input.frequency: 50.0
    * input.frequency.nominal: 50
    * input.voltage: 233.0
    * input.voltage.fault: 140.0
    * input.voltage.nominal: 220
    * output.voltage: 220.0
    * ups.delay.shutdown: 30
    * ups.delay.start: 180
    * ups.load: 2
    * ups.productid: 00c9
    * ups.status: OL
    * ups.temperature: 32.0
    * ups.type: online
    * ups.vendorid: 14f0


*upscmd -l:*
Instant commands supported on UPS [ups1]:

    * beeper.toggle - Toggle the UPS beeper -> returns OK, but seems to
      have no effect
    * load.off - Turn off the load immediately -> returns OK, but seems
      to have no effect
    * load.on - Turn on the load immediately -> returns OK, but seems to
      have no effect
    * shutdown.return - Turn off the load and return when power is back
      -> returns OK, but seems to have no effect
    * shutdown.stayoff - Turn off the load and remain off -> returns OK,
      but seems to have no effect
    * shutdown.stop - Stop a shutdown in progress -> returns OK, but
      seems to have no effect
    * test.battery.start - Start a battery test -> OK, starts a test,
      UPS status changes to 'OL CAL' (didn't wait for the test to finish)
    * test.battery.start.deep - Start a deep battery test -> returns OK,
      starts a test, UPS status changes to 'OL CAL' (didn't wait for the
      test to finish)
    * test.battery.start.quick - Start a quick battery test -> returns
      OK, starts a test, UPS status changes to 'OL CAL' for a short time
    * test.battery.stop - Stop the battery test - OK, stops a test, UPS
      status changes back to 'OL'


NOTE - issuing several 'test.battery.start*' commands without
'test.battery.stop' kills USB communication. The UPS needs to be
disconnected and re-connected to USB before communication can be
re-established.

*upsrw* - no output


I couldn't test the shutdown procedure as we also have a generating set
- hopefully I'll never see the shutdown procedure.

  Best regards, Danilo



-- 
Danilo Godec, sistemska podpora / system administration

Predlog! Obiscite prenovljeno spletno stran www.agenda.si 

ODPRTA KODA IN LINUX 
STORITVE : POSLOVNE RESITVE : UPRAVLJANJE IT : INFRASTRUKTURA IT : IZOBRAZEVANJE : PROGRAMSKA OPREMA 

Visit our updated web page at www.agenda.si 

OPEN SOURCE AND LINUX 
SERVICES : BUSINESS SOLUTIONS : IT MANAGEMENT : IT INFRASTRUCTURE : TRAINING : SOFTWARE 

-------------- next part --------------
An HTML attachment was scrubbed...
URL: <http://lists.alioth.debian.org/pipermail/nut-upsuser/attachments/20110420/56975bfe/attachment.htm>