[Nut-upsuser] request - nutdrv_qx_megatec.c: update/fix the code for "new" UPS

Jim Klimov jimklimov+nut at gmail.com
Thu Aug 18 18:49:20 BST 2022


I can best suppose so far that for one, printf in shell may differ from
that  in C and from scanf for that matter. And I think OTOH that scanf can
signal an error if the formatting string does not match expected pattern.
Maybe this is what happens to reject the device, maybe some other fault.

Try finding where it parses that input to fall back treating `-.--` as zero
or something to mean "known-mussing"... Ideally just a lack of that reading
in dstate, in the end - e.g. no temperature field for this device.

On Tue, Aug 16, 2022, 15:24 Tomáš Thiemel <thiemel at centrum.cz> wrote:

> Hi Jim,
>
> I am afraid that the main problem is in '%.1f' in the "lookup table" when
> UPS returns "--.-" (string) instead of "12.3" (float):
>
>
> root at OpenWrt:~# printf '%.1f \n' "12.3"
>
> 12.3
>
> root at OpenWrt:~# printf '%.1f \n' "--.-"
>
> ash: invalid number '--.-'
>
> 0.0
>
>
> I checked source codes at
> https://github.com/networkupstools/nut/tree/master/drivers and all these
> protocols have similar "lookup table":
>
> - nutdrv_qx_zinto.c
>
> - nutdrv_qx_voltronic-qs.c
>
> - nutdrv_qx_q1.c
>
> - nutdrv_qx_mustek.c
>
> - nutdrv_qx_megatec.c
>
> - nutdrv_qx_megatec-old.c
>
> - nutdrv_qx_mecer.c
>
> - nutdrv_qx_hunnox.c
>
> - nutdrv_qx_bestups.c
>
>
> BTW - I already wrote some "basic" code in Python using PyUSB to read
> desired data from the UPS, but the communication with it is very very bad. Probably
> due to the bad the quality of the electronics in it. Sometimes it returns
> data with missing initial characters (missing first 8 bytes) so I have to
> re-read the status, sometimes the communication freezes completely so I
> have to power-cycle the USB port.
>
>
>
> Best regards / S pozdravem
>
>
>
> Tomáš Thiemel
>
> thiemel at centrum.cz
>
>
>
> ______________________________________________________________
> > Od: "Jim Klimov" <jimklimov+nut at gmail.com>
> > Komu: "Tomáš Thiemel" <thiemel at centrum.cz>
> > Datum: 16.08.2022 12:44
> > Předmět: Re: [Nut-upsuser] request - nutdrv_qx_megatec.c: update/fix the
> code for "new" UPS
> >
>
> > CC: <nut-upsuser at alioth-lists.debian.net>
> Ahoj,
>   Just in case, did you check other subdrivers there? They all are for
> variants of Megatec Qx family, UPS vendors were creative with it...
> Jim
>
> On Tue, Aug 16, 2022, 03:46 Tomáš Thiemel via Nut-upsuser <
> nut-upsuser at alioth-lists.debian.net> wrote:
>
>> Hi.
>>
>> I bought new UPS which is not "supported", yet.
>>
>>
>>
>> Brand: Volt Polska
>>
>> Model: Micro 800
>>
>> have USB with Megatec protocol ("Q1<cr>")
>>
>> Data returned by UPS: *"(242.9 242.9 242.9 000 50.0 13.3 --.- 00001001"*
>>
>> Problem: data returned by UPS is not handled correctly by
>> nutdrv_qx/megatec driver, although the SW from
>> https://www.power-software-download.com/viewpower.html (JAVA) works fine.
>>
>>
>>
>> "ups.temperature" is defined as "%.1f" in the source code but my UPS
>> returns "--.-"
>>
>>
>> Debug info:
>>
>> root at patschkav-OpenWrt:~# /lib/nut/nutdrv_qx -DDDDDDDDDD -a ups -x
>> protocol=megatec
>>
>> Network UPS Tools - Generic Q* USB/Serial driver 0.28 (2.7.4)
>>
>> USB communication driver 0.33
>>
>>    0.000000     send_to_all: SETINFO driver.parameter.port "auto"
>>
>>    0.006788     send_to_all: SETINFO driver.parameter.vendorid "0665"
>>
>>    0.008047     send_to_all: SETINFO driver.parameter.productid "5161"
>>
>>    0.010655     send_to_all: SETINFO driver.parameter.protocol "megatec"
>>
>>    0.011858     debug level is '10'
>>
>>    0.014225     upsdrv_initups...
>>
>>    0.019924     Checking device (0665/5161) (001/014)
>>
>>    0.036693     - VendorID: 0665
>>
>>    0.036788     - ProductID: 5161
>>
>>    0.036819     - Manufacturer: unknown
>>
>>    0.036850     - Product:
>>
>>    0.036881     - Serial Number: unknown
>>
>>    0.036912     - Bus: 001
>>
>>    0.036942     - Device release number: 0002
>>
>>    0.036971     Trying to match device
>>
>>    0.037069     Device matches
>>
>>    0.037178     nut_usb_set_altinterface: skipped
>> usb_set_altinterface(udev, 0)
>>
>>    0.037262     send_to_all: SETINFO ups.vendorid "0665"
>>
>>    0.037317     send_to_all: SETINFO ups.productid "5161"
>>
>>    0.037361     Skipping protocol Voltronic 0.06
>>
>>    0.037399     Skipping protocol Voltronic-QS 0.07
>>
>>    0.037438     Skipping protocol Voltronic-QS-Hex 0.10
>>
>>    0.037477     Skipping protocol Mustek 0.07
>>
>>    0.037514     Skipping protocol Megatec/old 0.07
>>
>>    0.037551     Skipping protocol BestUPS 0.06
>>
>>    0.037589     Skipping protocol Mecer 0.07
>>
>>    0.052692     send: Q1
>>
>>    0.054678     read: timeout (0)
>>
>>    0.054842     qx_process_answer: short reply (input.voltage)
>>
>>    1.465747     send: Q1
>>
>>    1.494790     read [  0]: (8 bytes) => 28 32 34 30 2e 38 20 32
>>
>>    1.526803     read [  8]: (8 bytes) => 34 30 2e 38 20 32 34 30
>>
>>    1.558795     read [ 16]: (8 bytes) => 2e 38 20 30 30 30 20 35
>>
>>    1.590799     read [ 24]: (8 bytes) => 30 2e 32 20 31 33 2e 33
>>
>>    1.622797     read [ 32]: (8 bytes) => 20 2d 2d 2e 2d 20 30 30
>>
>>    1.654819     read [ 40]: (8 bytes) => 30 30 31 30 30 31 0d 00
>>
>>    1.654919     read: (240.8 240.8 240.8 000 50.2 13.3 --.- 00001001
>>
>>    1.655052     send_to_all: SETINFO input.voltage "240.8"
>>
>>    3.061834     send: I
>>
>>    3.094895     read [  0]: (8 bytes) => 31 0d 00 00 00 00 00 00
>>
>>    3.094994     read: 1
>>
>>    3.095100     qx_process_answer: short reply (ups.firmware)
>>
>>    3.095161     send_to_all: DELINFO input.voltage
>>
>>    4.506937     send: Q1
>>
>>    5.509389     read: Operation timed out (-145)
>>
>>    5.509494     qx_process_answer: short reply (input.voltage)
>>
>>    5.509541     Skipping protocol Zinto 0.06
>>
>>    5.509578     Skipping protocol Q1 0.07
>>
>>    5.509608     Device not supported!
>>
>>    5.509638     Device not supported!
>> Can some skilled programmer fix the code in nutdrv_qx_megatec.c, please?
>> I'm just stupid sysadmin. :-(
>> Thank you very much.
>>
>>
>>
>> Best regards / S pozdravem
>>
>>
>>
>> Tomáš Thiemel
>>
>> thiemel at centrum.cz
>>
>>
>>
>> _______________________________________________
>> Nut-upsuser mailing list
>> Nut-upsuser at alioth-lists.debian.net
>> https://alioth-lists.debian.net/cgi-bin/mailman/listinfo/nut-upsuser
>
>
-------------- next part --------------
An HTML attachment was scrubbed...
URL: <http://alioth-lists.debian.net/pipermail/nut-upsuser/attachments/20220818/66cfc3c1/attachment.htm>


More information about the Nut-upsuser mailing list