[Nut-upsuser] Can't claim USB device: Invalid parameter

Wed Feb 7 21:50:34 GMT 2024

Hello, thanks for the details although I too am not sure about the "invalid
parameter" - got neither reasons nor solutions at the moment.

Regarding the "device: unknown", there was an issue in the USB matcher code
that did not let the driver "remember" the value it saw from libusb (and so
it could not match if the desired value was requested in ups.conf). That
was fixed in NUT v2.8.1; however, given the inherent unreliability of these
numbers (dependent on hotplug events, USB ports used and presence of other
devices, etc.), nut-scanner would not suggest them to be part of the driver
configuration section by default starting with NUT v2.8.2 (and current
master already).

Your config did not mention these link-specific numbers, so I think it
should not be the problem in your case.

Jim

On Wed, Feb 7, 2024 at 10:09 PM Jason Doolittle <jason at flintegratedtech.com>
wrote:

> I think I have another lead:
>
> For the Powervar, lsusb gives:
>
> Bus 003 Device 002: ID 4234:0002 AMETEK-POWERVAR Corporation UPM UPS
> (v01.51, Nov  3 2018)
> When running usbhid-ups from the command line, I get:
>
> 0.035977 [D2] - Bus: 003
> 0.035989 [D2] - Device: unknown
>
> So is it passing "unknown" as the device number to libusb instead of 002?
>
> On Wed, Feb 7, 2024, at 3:54 PM, Jason Doolittle wrote:
>
> Hello,
>
> Thanks for your reply.
>
> Both of the services you mentioned (nut-driver at PowervarUPS01.service and
> nut-driver at APCUPS01.service) were running. They were spamming syslog with
> messages like the following:
>
> 2024-02-07T14:29:27.704506-05:00 hostname nut-driver at PowervarUPS01[72162]:
> Network UPS Tools - Generic HID driver 0.47 (2.8.0)
>
> 2024-02-07T14:29:27.704537-05:00 hostname nut-driver at PowervarUPS01[72162]:
> USB communication driver (libusb 1.0) 0.43
>
> 2024-02-07T14:29:27.704873-05:00 hostname nut-driver at PowervarUPS01[72161]:
> Driver failed to start (exit status=1)
>
> 2024-02-07T14:29:32.718262-05:00 hostname nut-driver at PowervarUPS01[72167]:
> Can't claim USB device [4234:0002]@1/0: Invalid parameter
>
> 2024-02-07T14:29:32.718386-05:00 hostname nut-driver at PowervarUPS01[72167]:
> Network UPS Tools - Generic HID driver 0.47 (2.8.0)
>
> 2024-02-07T14:29:32.718422-05:00 hostname nut-driver at PowervarUPS01[72167]:
> USB communication driver (libusb 1.0) 0.43
>
> 2024-02-07T14:29:32.718684-05:00 hostname nut-driver at PowervarUPS01[72161]:
> Driver failed to start (exit status=1)
>
> 2024-02-07T14:29:32.718829-05:00 hostname nut-driver at APCUPS01[72166]:
> Can't claim USB device [051d:0002]@1/0: Invalid parameter
>
> After stopping those services I ran the driver again from the CLI with the
> same result. That "Invalid parameter" is conspicuous. I haven't seen it in
> anyone else's questions or answers. The only place i've seen it in relation
> to this problem is in libusb1.c (on github), but not in a way that makes it
> obvious how to track down the cause. I suspect some sort of version or
> parameter mismatch somewhere in libusb, but I have no idea how to test for
> that.
>
>
> On Wed, Feb 7, 2024, at 12:57 PM, Jim Klimov wrote:
>
> Hello and welcome!
>
>   My guess would be that a nut-driver service unit (or instances thereof
> since NUT v2.8.0, monolithic before) have started and captured the devices,
> so your attempts with another copy of the driver started from CLI fail at
> that. Normally drivers detect an older sibling running (by poking a PID
> file), but service units may forgo creation of one. (Since 2.8.1 they can
> also try to use driver-server protocol locally.)
>
>   Since NUT v2.8.0 there is a nut-driver-enumerator (script and service)
> which manages creation, deletion and reloading/restarting of unit instances
> based on ups.conf contents (start-up) or changes (run-time). Check if you
> have `nut-driver at PowervarUPS01.service` (and `... at APCUPS01`) there to fit
> this bill? If yes, then to experiment with CLI copies of drivers,
> `systemctl stop` such unit(s).
>
> Hope this helps,
> Jim Klimov
>
>
> On Wed, Feb 7, 2024, 14:48 Jason Doolittle <jason at flintegratedtech.com>
> wrote:
>
> I am working in Ubuntu Linux on a Raspberry Pi 5. Nut is unable to connect
> to USB UPSs.
>
> uname -srvmpio
> Linux 6.5.0-1009-raspi #12-Ubuntu SMP PREEMPT_DYNAMIC Wed Jan 17 11:45:08
> UTC 2024 aarch64 aarch64 aarch64 GNU/Linux
>
> Current Installed version of nut is 2.8.0-7 installed with apt
>
> apt-cache policy nut
> nut:
>   Installed: 2.8.0-7
>   Candidate: 2.8.0-7
>   Version table:
> *** 2.8.0-7 500
>         500 http://ports.ubuntu.com/ubuntu-ports mantic/main arm64
> Packages
>         100 /var/lib/dpkg/status
>
> I currently have 2 UPSs connected to the system
> A Powervar UPM UPS
> Bus 003 Device 002: ID 4234:0002 AMETEK-POWERVAR Corporation UPM UPS
> (v01.51, Nov  3 2018)
>
> An APC Back-UPS Pro 1500
> Bus 001 Device 002: ID 051d:0002 American Power Conversion Uninterruptible
> Power Supply
>
> It appears that the all of the permissions were set up correctly during
> installation. The nut user and group were created and the usb devices have
> the correct ownership and permissions set per the udev rules
>
> For the Powervar:
> crw-rw-r-- 1 root nut 189, 257 Feb  7 06:42 /dev/bus/usb/003/002
>
> For the APC:
> crw-rw-r-- 1 root nut 189, 1 Feb  7 06:42 /dev/bus/usb/001/002
>
> In ups.conf, I have this:
>
> [PowervarUPS01]
> driver = "usbhid-ups"
> port = "auto"
> vendorid = "4234"
> productid = "0002"
>
> [APCUPS01]
> driver = "usbhid-ups"
> port = "auto"
> vendorid = "051D"
> productid = "0002"
>
> The UPSs are matched, but drivers continuously fail to start. Here is the
> output from running the usbhid-ups driver manually for the Powervar:
>
> sudo /usr/lib/nut/usbhid-ups -u root -a PowervarUPS01 -DD
>
> Network UPS Tools - Generic HID driver 0.47 (2.8.0)
> USB communication driver (libusb 1.0) 0.43
>    0.000000 [D1] debug level is '2'
>    0.001191 [D2] Initializing an USB-connected UPS with library
> libusb-1.0.26 (API: 0x1000109) (NUT subdriver name='USB communication
> driver (libusb 1.0)' ver='0.43')
>    0.001209 [D1] upsdrv_initups (non-SHUT)...
>    0.006358 [D2] Checking device 1 of 6 (1D6B/0003)
>    0.006385 [D1] Failed to open device (1D6B/0003), skipping: Access
> denied (insufficient permissions)
>    0.006393 [D2] Checking device 2 of 6 (4234/0002)
>    0.007354 [D2] - VendorID: 4234
>    0.007364 [D2] - ProductID: 0002
>    0.007371 [D2] - Manufacturer: AMETEK-POWERVAR Corporation
>    0.007378 [D2] - Product: UPM UPS (v01.51, Nov  3 2018)
>    0.007385 [D2] - Serial Number: 5008094R-1940438
>    0.007395 [D2] - Bus: 003
>    0.007402 [D2] - Device: unknown
>    0.007409 [D2] - Device release number: 0002
>    0.007418 [D2] Trying to match device
>    0.007425 [D2] match_function_subdriver (non-SHUT mode): matching a
> device...
>    0.007485 [D2] Device matches
>    0.007497 [D2] Reading first configuration descriptor
>    0.007505 [D2] result: -5 (Entity not found)
>    0.007517 [D2] failed to claim USB device: Entity not found
>    0.007529 [D1] failed to detach kernel driver from USB device: Invalid
> parameter
>    0.007539 [D2] failed to claim USB device: Entity not found
>    0.007549 [D1] failed to detach kernel driver from USB device: Invalid
> parameter
>    0.007560 [D2] failed to claim USB device: Entity not found
>    0.007574 [D1] failed to detach kernel driver from USB device: Invalid
> parameter
>    0.007582 [D2] failed to claim USB device: Entity not found
>    0.007594 [D1] failed to detach kernel driver from USB device: Invalid
> parameter
>    0.007604 Can't claim USB device [4234:0002]@1/0: Invalid parameter
>
> I get basically the same from the APC.
>
> I think the "failed to detach kernel driver from USB device: Invalid
> parameter" is the key here, especially the "Invalid parameter" part, but
> after a few hours of poking at things, I haven't made any progress.
>
> I would be eternally grateful if someone could point me in the right
> direction.
>
> _______________________________________________
> Nut-upsuser mailing list
> Nut-upsuser at alioth-lists.debian.net
> https://alioth-lists.debian.net/cgi-bin/mailman/listinfo/nut-upsuser
>
>
> _______________________________________________
> Nut-upsuser mailing list
> Nut-upsuser at alioth-lists.debian.net
> https://alioth-lists.debian.net/cgi-bin/mailman/listinfo/nut-upsuser
>
>
> --
> Jason Doolittle
> Facility Engineer
> jason at flintegratedtech.com | 813 918-6157
>
>
-------------- next part --------------
An HTML attachment was scrubbed...
URL: <http://alioth-lists.debian.net/pipermail/nut-upsuser/attachments/20240207/15078464/attachment-0001.htm>