[Pkg-fglrx-devel] Bug#557233: fglrx-driver: fails to load FireMV 2400
Donald Kayser
xorg at kayser.net
Fri Nov 20 09:05:49 UTC 2009
Package: fglrx-driver
Version: 1:9-10-1
Severity: serious
Justification: important
I recently updated to the most recent fglrx driver in hopes of getting support for this 4-head
dual-chip FireMV 2400 graphics adapter. This driver worked on one set of screens prior to the most
recent update. I installed the 2.6.26-2-686 kernel and modules as a possible solution, but it
fails also. I was able to use this driver with the lenny distribution, but then I upgraded from
squeeze these newest drivers, and ever since, X will not load. I mostly have been using the
2.6.30.2 kernel, and built modules for it, and had the same results as with both kernels.
--------------------------------------------------------------------
lspci -vv
00:00.0 Host bridge: Intel Corporation 82945G/GZ/P/PL Memory Controller Hub (rev 02)
Subsystem: Intel Corporation 82945G/GZ/P/PL Memory Controller Hub
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR-
FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort+ >SERR-
<PERR- INTx-
Latency: 0
Capabilities: <access denied>
Kernel modules: intel-agp
00:01.0 PCI bridge: Intel Corporation 82945G/GZ/P/PL PCI Express Root Port (rev 02) (prog-if 00
[Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR-
FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR-
<PERR- INTx-
Latency: 0, Cache Line Size: 4 bytes
Bus: primary=00, secondary=01, subordinate=04, sec-latency=0
I/O behind bridge: 00007000-00008fff
Memory behind bridge: fd700000-fd9fffff
Prefetchable memory behind bridge: 00000000b0000000-00000000cfffffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort+ <SERR-
<PERR-
BridgeCtl: Parity- SERR- NoISA+ VGA+ MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: <access denied>
Kernel driver in use: pcieport-driver
Kernel modules: shpchp
00:1b.0 Audio device: Intel Corporation 82801G (ICH7 Family) High Definition Audio Controller (rev
01)
Subsystem: Intel Corporation DeskTop Board D945GTP
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR-
FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR-
<PERR- INTx-
Latency: 0, Cache Line Size: 4 bytes
Interrupt: pin A routed to IRQ 16
Region 0: Memory at fdff8000 (64-bit, non-prefetchable) [size=16K]
Capabilities: <access denied>
Kernel driver in use: HDA Intel
Kernel modules: snd-hda-intel
00:1c.0 PCI bridge: Intel Corporation 82801G (ICH7 Family) PCI Express Port 1 (rev 01) (prog-if 00
[Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR-
FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR-
<PERR- INTx-
Latency: 0, Cache Line Size: 4 bytes
Bus: primary=00, secondary=05, subordinate=05, sec-latency=0
I/O behind bridge: 00006000-00006fff
Memory behind bridge: fd400000-fd4fffff
Prefetchable memory behind bridge: 00000000fde00000-00000000fdefffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR-
<PERR-
BridgeCtl: Parity- SERR- NoISA+ VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: <access denied>
Kernel driver in use: pcieport-driver
Kernel modules: shpchp
00:1c.1 PCI bridge: Intel Corporation 82801G (ICH7 Family) PCI Express Port 2 (rev 01) (prog-if 00
[Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR-
FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR-
<PERR- INTx-
Latency: 0, Cache Line Size: 4 bytes
Bus: primary=00, secondary=06, subordinate=06, sec-latency=0
I/O behind bridge: 0000c000-0000cfff
Memory behind bridge: fdd00000-fddfffff
Prefetchable memory behind bridge: 00000000fdc00000-00000000fdcfffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR-
<PERR-
BridgeCtl: Parity- SERR- NoISA+ VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: <access denied>
Kernel driver in use: pcieport-driver
Kernel modules: shpchp
00:1c.2 PCI bridge: Intel Corporation 82801G (ICH7 Family) PCI Express Port 3 (rev 01) (prog-if 00
[Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR-
FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR-
<PERR- INTx-
Latency: 0, Cache Line Size: 4 bytes
Bus: primary=00, secondary=07, subordinate=07, sec-latency=0
I/O behind bridge: 0000b000-0000bfff
Memory behind bridge: fdb00000-fdbfffff
Prefetchable memory behind bridge: 00000000fda00000-00000000fdafffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR-
<PERR-
BridgeCtl: Parity- SERR- NoISA+ VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: <access denied>
Kernel driver in use: pcieport-driver
Kernel modules: shpchp
00:1d.0 USB Controller: Intel Corporation 82801G (ICH7 Family) USB UHCI Controller #1 (rev 01)
(prog-if 00 [UHCI])
Subsystem: Intel Corporation 82801G (ICH7 Family) USB UHCI Controller #1
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR-
FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR-
<PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 23
Region 4: I/O ports at fc00 [size=32]
Kernel driver in use: uhci_hcd
Kernel modules: uhci-hcd
00:1d.1 USB Controller: Intel Corporation 82801G (ICH7 Family) USB UHCI Controller #2 (rev 01)
(prog-if 00 [UHCI])
Subsystem: Intel Corporation 82801G (ICH7 Family) USB UHCI Controller #2
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR-
FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR-
<PERR- INTx-
Latency: 0
Interrupt: pin B routed to IRQ 19
Region 4: I/O ports at f800 [size=32]
Kernel driver in use: uhci_hcd
Kernel modules: uhci-hcd
00:1d.2 USB Controller: Intel Corporation 82801G (ICH7 Family) USB UHCI Controller #3 (rev 01)
(prog-if 00 [UHCI])
Subsystem: Intel Corporation 82801G (ICH7 Family) USB UHCI Controller #3
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR-
FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR-
<PERR- INTx-
Latency: 0
Interrupt: pin C routed to IRQ 18
Region 4: I/O ports at f400 [size=32]
Kernel driver in use: uhci_hcd
Kernel modules: uhci-hcd
00:1d.3 USB Controller: Intel Corporation 82801G (ICH7 Family) USB UHCI Controller #4 (rev 01)
(prog-if 00 [UHCI])
Subsystem: Intel Corporation Device 27ca
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR-
FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR-
<PERR- INTx-
Latency: 0
Interrupt: pin D routed to IRQ 16
Region 4: I/O ports at f000 [size=32]
Kernel driver in use: uhci_hcd
Kernel modules: uhci-hcd
00:1d.7 USB Controller: Intel Corporation 82801G (ICH7 Family) USB2 EHCI Controller (rev 01)
(prog-if 20 [EHCI])
Subsystem: Intel Corporation 82801G (ICH7 Family) USB2 EHCI Controller
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR-
FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR-
<PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 23
Region 0: Memory at fdfff000 (32-bit, non-prefetchable) [size=1K]
Capabilities: <access denied>
Kernel driver in use: ehci_hcd
Kernel modules: ehci-hcd
00:1e.0 PCI bridge: Intel Corporation 82801 PCI Bridge (rev e1) (prog-if 01 [Subtractive decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR-
FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR-
<PERR- INTx-
Latency: 0
Bus: primary=00, secondary=08, subordinate=08, sec-latency=32
I/O behind bridge: 00009000-0000afff
Memory behind bridge: fd600000-fd6fffff
Prefetchable memory behind bridge: 00000000fd500000-00000000fd5fffff
Secondary status: 66MHz- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ <SERR-
<PERR-
BridgeCtl: Parity- SERR- NoISA+ VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: <access denied>
00:1f.0 ISA bridge: Intel Corporation 82801GB/GR (ICH7 Family) LPC Interface Bridge (rev 01)
Subsystem: Intel Corporation 82801GB/GR (ICH7 Family) LPC Interface Bridge
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+
FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR-
<PERR- INTx-
Latency: 0
Capabilities: <access denied>
Kernel modules: intel-rng, iTCO_wdt
00:1f.1 IDE interface: Intel Corporation 82801G (ICH7 Family) IDE Controller (rev 01) (prog-if 8a
[Master SecP PriP])
Subsystem: Intel Corporation 82801G (ICH7 Family) IDE Controller
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR-
FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR-
<PERR- INTx+
Latency: 0
Interrupt: pin A routed to IRQ 18
Region 0: I/O ports at 01f0 [size=8]
Region 1: I/O ports at 03f4 [size=1]
Region 2: I/O ports at 0170 [size=8]
Region 3: I/O ports at 0374 [size=1]
Region 4: I/O ports at ec00 [size=16]
Kernel driver in use: PIIX_IDE
Kernel modules: piix
00:1f.2 SATA controller: Intel Corporation 82801GR/GH (ICH7 Family) SATA AHCI Controller (rev 01)
(prog-if 01 [AHCI 1.0])
Subsystem: Intel Corporation Device 27c0
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR-
FastB2B- DisINTx+
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR-
<PERR- INTx-
Latency: 0
Interrupt: pin B routed to IRQ 214
Region 0: I/O ports at e800 [size=8]
Region 1: I/O ports at e400 [size=4]
Region 2: I/O ports at e000 [size=8]
Region 3: I/O ports at dc00 [size=4]
Region 4: I/O ports at d800 [size=16]
Region 5: Memory at fdffe000 (32-bit, non-prefetchable) [size=1K]
Capabilities: <access denied>
Kernel driver in use: ahci
Kernel modules: ahci
00:1f.3 SMBus: Intel Corporation 82801G (ICH7 Family) SMBus Controller (rev 01)
Subsystem: Intel Corporation 82801G (ICH7 Family) SMBus Controller
Control: I/O+ Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR-
FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR-
<PERR- INTx-
Interrupt: pin B routed to IRQ 19
Region 4: I/O ports at 0500 [size=32]
Kernel driver in use: i801_smbus
Kernel modules: i2c-i801
01:00.0 PCI bridge: PLX Technology, Inc. PEX 8517 16-lane, 5-port PCI Express Switch (rev ac)
(prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR-
FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR-
<PERR- INTx-
Latency: 0, Cache Line Size: 4 bytes
Region 0: Memory at fd9e0000 (32-bit, non-prefetchable) [size=128K]
Bus: primary=01, secondary=02, subordinate=04, sec-latency=0
I/O behind bridge: 00007000-00008fff
Memory behind bridge: fd700000-fd8fffff
Prefetchable memory behind bridge: 00000000b0000000-00000000cfffffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR-
<PERR-
BridgeCtl: Parity- SERR- NoISA+ VGA+ MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: <access denied>
Kernel driver in use: pcieport-driver
Kernel modules: shpchp
02:01.0 PCI bridge: PLX Technology, Inc. PEX 8517 16-lane, 5-port PCI Express Switch (rev ac)
(prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR-
FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR-
<PERR- INTx-
Latency: 0, Cache Line Size: 4 bytes
Bus: primary=02, secondary=03, subordinate=03, sec-latency=0
I/O behind bridge: 00008000-00008fff
Memory behind bridge: fd800000-fd8fffff
Prefetchable memory behind bridge: 00000000c0000000-00000000cfffffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR-
<PERR-
BridgeCtl: Parity- SERR- NoISA+ VGA+ MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: <access denied>
Kernel driver in use: pcieport-driver
Kernel modules: shpchp
02:02.0 PCI bridge: PLX Technology, Inc. PEX 8517 16-lane, 5-port PCI Express Switch (rev ac)
(prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR-
FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR-
<PERR- INTx-
Latency: 0, Cache Line Size: 4 bytes
Bus: primary=02, secondary=04, subordinate=04, sec-latency=0
I/O behind bridge: 00007000-00007fff
Memory behind bridge: fd700000-fd7fffff
Prefetchable memory behind bridge: 00000000b0000000-00000000bfffffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR-
<PERR-
BridgeCtl: Parity- SERR- NoISA+ VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: <access denied>
Kernel driver in use: pcieport-driver
Kernel modules: shpchp
03:00.0 VGA compatible controller: ATI Technologies Inc M24 [FireMV 2400] (prog-if 00 [VGA
controller])
Subsystem: ATI Technologies Inc M24 [FireMV 2400]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR-
FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR-
<PERR- INTx-
Latency: 0, Cache Line Size: 4 bytes
Interrupt: pin A routed to IRQ 10
Region 0: Memory at c0000000 (32-bit, prefetchable) [size=256M]
Region 1: I/O ports at 8c00 [size=256]
Region 2: Memory at fd8f0000 (32-bit, non-prefetchable) [size=64K]
[virtual] Expansion ROM at fd800000 [disabled] [size=128K]
Capabilities: <access denied>
03:00.1 Display controller: ATI Technologies Inc M24 [FireMV 2400] (Secondary)
Subsystem: ATI Technologies Inc Device 3150
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR-
FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR-
<PERR- INTx-
Latency: 0, Cache Line Size: 4 bytes
Region 0: Memory at fd8e0000 (32-bit, non-prefetchable) [size=64K]
Capabilities: <access denied>
04:00.0 Display controller: ATI Technologies Inc M24 [FireMV 2400]
Subsystem: ATI Technologies Inc M24 [FireMV 2400]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR-
FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR-
<PERR- INTx-
Latency: 0, Cache Line Size: 4 bytes
Interrupt: pin A routed to IRQ 11
Region 0: Memory at b0000000 (32-bit, prefetchable) [size=256M]
Region 1: I/O ports at 7c00 [size=256]
Region 2: Memory at fd7f0000 (32-bit, non-prefetchable) [size=64K]
[virtual] Expansion ROM at fd700000 [disabled] [size=128K]
Capabilities: <access denied>
04:00.1 Display controller: ATI Technologies Inc M24 [FireMV 2400] (Secondary)
Subsystem: ATI Technologies Inc Device 3150
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR-
FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR-
<PERR- INTx-
Latency: 0, Cache Line Size: 4 bytes
Region 0: Memory at fd7e0000 (32-bit, non-prefetchable) [size=64K]
Capabilities: <access denied>
06:00.0 Ethernet controller: Intel Corporation 82573L Gigabit Ethernet Controller
Subsystem: ASUSTeK Computer Inc. Device 81c2
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR-
FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR-
<PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 216
Region 0: Memory at fdde0000 (32-bit, non-prefetchable) [size=128K]
Region 2: I/O ports at cc00 [size=32]
Capabilities: <access denied>
Kernel driver in use: e1000e
Kernel modules: e1000e
07:00.0 Ethernet controller: Intel Corporation 82573L Gigabit Ethernet Controller
Subsystem: ASUSTeK Computer Inc. Device 81c2
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR-
FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR-
<PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 215
Region 0: Memory at fdbe0000 (32-bit, non-prefetchable) [size=128K]
Region 2: I/O ports at bc00 [size=32]
Capabilities: <access denied>
Kernel driver in use: e1000e
Kernel modules: e1000e
08:0a.0 RAID bus controller: Integrated Technology Express, Inc. IT/ITE8212 Dual channel ATA RAID
controller (rev 13)
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR-
FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR-
<PERR- INTx-
Latency: 64 (2000ns min, 2000ns max)
Interrupt: pin A routed to IRQ 19
Region 0: I/O ports at ac00 [size=8]
Region 1: I/O ports at a800 [size=4]
Region 2: I/O ports at a400 [size=8]
Region 3: I/O ports at a000 [size=4]
Region 4: I/O ports at 9c00 [size=16]
[virtual] Expansion ROM at fd500000 [disabled] [size=128K]
Capabilities: <access denied>
Kernel driver in use: ITE821x IDE
Kernel modules: it821x
----------------------------------------------------------------------
xorg.conf
Section "ServerLayout"
Identifier "Main Layout"
Screen "MainVGA"
#Screen "SecondaryVGA"
InputDevice "Keyboard0" "CoreKeyboard"
InputDevice "Mouse0" "CorePointer"
EndSection
Section "InputDevice"
Identifier "Keyboard0"
Driver "kbd"
Option "XkbRules" "xorg"
Option "XkbModel" "pc104"
Option "XkbLayout" "us"
EndSection
Section "InputDevice"
Identifier "Mouse0"
Driver "mouse"
Option "Protocol" "auto"
Option "Device" "/dev/input/mice"
Option "Emulate3Buttons" "no"
Option "ZAxisMapping" "4 5"
EndSection
Section "Monitor"
Identifier "Monitor0"
VendorName "Unknown"
ModelName "Unknown"
Option "DPMS"
EndSection
Section "Monitor"
Identifier "Monitor1"
VendorName "Unknown"
ModelName "Unknown"
Option "DPMS"
#Option "LeftOf" "Monitor0"
EndSection
Section "Monitor"
Identifier "Monitor2"
VendorName "Unknown"
ModelName "Unknown"
Option "DPMS"
EndSection
Section "Monitor"
Identifier "Monitor3"
VendorName "Unknown"
ModelName "Unknown"
Option "DPMS"
#Option "LeftOf" "Monitor2"
EndSection
Section "Device"
Identifier "ipc vga port right"
Driver "fglrx"
BusID "PCI:03:00:0"
#Option "Monitor-DVI-0" "Monitor0"
#Option "Monitor-DVI-1" "Monitor1"
EndSection
Section "Device"
Identifier "ipc vga port left"
Driver "fglrx"
BusID "PCI:04:00:0"
#Option "Monitor-DVI-0" "Monitor2"
#Option "Monitor-DVI-1" "Monitor3"
EndSection
Section "Screen"
Identifier "MainVGA"
Device "ipc vga port right"
Monitor "Monitor1"
DefaultDepth 24
SubSection "Display"
Depth 24
Modes "800x600"
Virtual 1600 600
EndSubSection
EndSection
Section "Screen"
Identifier "SecondaryVGA"
Device "ipc vga port left"
Monitor "Monitor3"
DefaultDepth 24
SubSection "Display"
Depth 24
Modes "800x600"
Virtual 1600 600
EndSubSection
EndSection
Section "Monitor"
Identifier "Configured Monitor"
EndSection
----------------------------------------------------------------------
Xorg.0.log
X.Org X Server 1.6.5
Release Date: 2009-10-11
X Protocol Version 11, Revision 0
Build Operating System: Linux 2.6.30.8-dsa-ia32 i686 Debian
Current Operating System: Linux hesipc 2.6.26-2-686 #1 SMP Wed Aug 19 06:06:52 UTC 2009 i686
Build Date: 13 October 2009 11:25:51AM
xorg-server 2:1.6.5-1 (buildd at murphy.debian.org)
Before reporting problems, check http://wiki.x.org
to make sure that you have the latest version.
Markers: (--) probed, (**) from config file, (==) default setting,
(++) from command line, (!!) notice, (II) informational,
(WW) warning, (EE) error, (NI) not implemented, (??) unknown.
(==) Log file: "/var/log/Xorg.0.log", Time: Fri Nov 20 08:28:34 2009
(==) Using config file: "/etc/X11/xorg.conf"
(==) ServerLayout "Main Layout"
(**) |-->Screen "MainVGA" (0)
(**) | |-->Monitor "Monitor1"
(**) | |-->Device "ipc vga port right"
(**) |-->Input Device "Keyboard0"
(**) |-->Input Device "Mouse0"
(==) Automatically adding devices
(==) Automatically enabling devices
(WW) The directory "/usr/share/fonts/X11/cyrillic" does not exist.
Entry deleted from font path.
(WW) The directory "/var/lib/defoma/x-ttcidfont-conf.d/dirs/TrueType" does not exist.
Entry deleted from font path.
(==) FontPath set to:
/usr/share/fonts/X11/misc,
/usr/share/fonts/X11/100dpi/:unscaled,
/usr/share/fonts/X11/75dpi/:unscaled,
/usr/share/fonts/X11/Type1,
/usr/share/fonts/X11/100dpi,
/usr/share/fonts/X11/75dpi,
built-ins
(==) ModulePath set to "/usr/lib/xorg/modules"
(WW) AllowEmptyInput is on, devices using drivers 'kbd', 'mouse' or 'vmmouse' will be disabled.
(WW) Disabling Keyboard0
(WW) Disabling Mouse0
(II) Loader magic: 0x6c0
(II) Module ABI versions:
X.Org ANSI C Emulation: 0.4
X.Org Video Driver: 5.0
X.Org XInput driver : 4.0
X.Org Server Extension : 2.0
(II) Loader running on linux
(--) using VT number 7
(--) PCI:*(0:3:0:0) 1002:3151:1002:3151 ATI Technologies Inc M24 [FireMV 2400] rev 0, Mem @
0xc0000000/268435456, 0xfd8f0000/65536, I/O @ 0x00008c00/256, BIOS @ 0x????????/131072
(WW) Open ACPI failed (/var/run/acpid.socket) (No such file or directory)
(II) No APM support in BIOS or kernel
(II) System resource ranges:
[0] -1 0 0xffffffff - 0xffffffff (0x1) MX[B]
[1] -1 0 0x000f0000 - 0x000fffff (0x10000) MX[B]
[2] -1 0 0x000c0000 - 0x000effff (0x30000) MX[B]
[3] -1 0 0x00000000 - 0x0009ffff (0xa0000) MX[B]
[4] -1 0 0x0000ffff - 0x0000ffff (0x1) IX[B]
[5] -1 0 0x00000000 - 0x00000000 (0x1) IX[B]
(II) LoadModule: "extmod"
(II) Loading /usr/lib/xorg/modules/extensions//libextmod.so
(II) Module extmod: vendor="X.Org Foundation"
compiled for 1.6.5, module version = 1.0.0
Module class: X.Org Server Extension
ABI class: X.Org Server Extension, version 2.0
(II) Loading extension SELinux
(II) Loading extension MIT-SCREEN-SAVER
(II) Loading extension XFree86-VidModeExtension
(II) Loading extension XFree86-DGA
(II) Loading extension DPMS
(II) Loading extension XVideo
(II) Loading extension XVideo-MotionCompensation
(II) Loading extension X-Resource
(II) LoadModule: "dbe"
(II) Loading /usr/lib/xorg/modules/extensions//libdbe.so
(II) Module dbe: vendor="X.Org Foundation"
compiled for 1.6.5, module version = 1.0.0
Module class: X.Org Server Extension
ABI class: X.Org Server Extension, version 2.0
(II) Loading extension DOUBLE-BUFFER
(II) LoadModule: "glx"
(II) Loading /usr/lib/xorg/modules/extensions//libglx.so
(II) Module glx: vendor="FireGL - ATI Technologies Inc."
compiled for 7.4.0, module version = 1.0.0
(II) Loading extension GLX
(II) LoadModule: "record"
(II) Loading /usr/lib/xorg/modules/extensions//librecord.so
(II) Module record: vendor="X.Org Foundation"
compiled for 1.6.5, module version = 1.13.0
Module class: X.Org Server Extension
ABI class: X.Org Server Extension, version 2.0
(II) Loading extension RECORD
(II) LoadModule: "dri"
(II) Loading /usr/lib/xorg/modules/extensions//libdri.so
(II) Module dri: vendor="X.Org Foundation"
compiled for 7.4.0, module version = 1.0.0
(II) Loading sub module "fglrxdrm"
(II) LoadModule: "fglrxdrm"
(II) Loading /usr/lib/xorg/modules/linux//libfglrxdrm.so
(II) Module fglrxdrm: vendor="FireGL - ATI Technologies Inc."
compiled for 1.4.99.906, module version = 8.66.2
(II) Loading extension XFree86-DRI
(II) LoadModule: "dri2"
(II) Loading /usr/lib/xorg/modules/extensions//libdri2.so
(II) Module dri2: vendor="X.Org Foundation"
compiled for 1.6.5, module version = 1.1.0
ABI class: X.Org Server Extension, version 2.0
(II) Loading extension DRI2
(II) LoadModule: "fglrx"
(II) Loading /usr/lib/xorg/modules/drivers//fglrx_drv.so
(II) Module fglrx: vendor="FireGL - ATI Technologies Inc."
compiled for 1.4.99.906, module version = 8.66.2
Module class: X.Org Video Driver
(II) Primary Device is: PCI 03 at 00:00:0
(WW) Falling back to old probe method for fglrx
(II) ATI Proprietary Linux Driver Version Identifier:8.66.2
(II) ATI Proprietary Linux Driver Release Identifier: 8.661
(II) ATI Proprietary Linux Driver Build Date: Sep 23 2009 17:30:14
(II) Loading PCS database from /etc/ati/amdpcsdb
(EE) No devices detected.
Fatal server error:
no screens found
---------------------------------------------------------------------
-- System Information:
Debian Release: 5.0.3
APT prefers testing
APT policy: (500, 'testing'), (500, 'stable')
Architecture: i386 (i686)
Kernel: Linux 2.6.26-2-686 (SMP w/2 CPU cores)
Locale: LANG=en_US.UTF-8, LC_CTYPE=en_US.UTF-8 (charmap=UTF-8)
Shell: /bin/sh linked to /bin/bash
Versions of packages fglrx-driver depends on:
ii debconf [debconf-2.0] 1.5.24 Debian configuration management sy
ii fglrx-glx 1:9-10-1 proprietary libGL for the non-free
ii laptop-detect 0.13.7 attempt to detect a laptop
ii libc6 2.10.1-7 GNU C Library: Shared libraries
ii libdrm2 2.4.14-1+b1 Userspace interface to kernel DRM
ii libgcc1 1:4.3.2-1.1 GCC support library
ii libgl1-mesa-glx [libgl1] 7.6-1 A free implementation of the OpenG
ii libx11-6 2:1.1.5-2 X11 client-side library
ii libxext6 2:1.0.4-1 X11 miscellaneous extension librar
ii libxinerama1 2:1.0.3-2 X11 Xinerama extension library
ii libxrandr2 2:1.2.3-1 X11 RandR extension library
ii libxrender1 1:0.9.4-2 X Rendering Extension client libra
ii xserver-xorg 1:7.4+4 the X.Org X server
Versions of packages fglrx-driver recommends:
ii fglrx-atieventsd 1:8-12-4 external events daemon for the non
ii fglrx-glx 1:9-10-1 proprietary libGL for the non-free
ii fglrx-kernel-2.6.26 1:9-10-1+2.6.26-19 ATI binary kernel module for Linux
ii fglrx-kernel-2.6.30 1:9-10-1+1.0 ATI binary kernel module for Linux
ii fglrx-modules-2.6.2 2.6.26+8-12-2+lenny1 Display driver for AMD/ATI Radeon
ii fglrx-source 1:9-10-1 kernel module source for the non-f
Versions of packages fglrx-driver suggests:
ii fglrx-control 1:8-12-4 control panel for the non-free AMD
-- debconf information:
fglrx-driver/acpi_switch: false
More information about the Pkg-fglrx-devel
mailing list