Excuse for replying so late.<br>I have reinstalled the debian from scratch.<br>I have burned a cd iso image before updating the os using aptitude full-upgrade, and I was able to burn the iso image successfully.<br>I have upgraded the system using aptitude full-upgrade.<br>
I have tried again today to burn iso image on a cd and it has shown error about inability to burn the media.<br>Please look into the matter.<br><br>The error produced due to the burning of the iso image :<br><br>System<br>
-----------------------<br>K3b Version: 1.0.5<br><br>KDE Version: 3.5.10<br>QT Version: 3.3.8b<br>Kernel: 2.6.26-2-686<br>Devices<br>-----------------------<br>HL-DT-ST RW/DVD GCC-4244N 1.03 (/dev/hdc, ) [CD-R, CD-RW, CD-ROM, DVD-ROM] [DVD-ROM, CD-ROM, CD-R, CD-RW] [SAO, TAO, RAW, SAO/R96P, SAO/R96R, RAW/R16, RAW/R96P, RAW/R96R]<br>
<br>Used versions<br>-----------------------<br>cdrecord: 1.1.9<br><br>cdrecord<br>-----------------------<br>/usr/bin/wodim: Operation not permitted. Warning: Cannot raise RLIMIT_MEMLOCK limits.<br>scsidev: '/dev/sr1'<br>
devname: '/dev/sr1'<br>scsibus: -2 target: -2 lun: -2<br>Linux sg driver version: 3.5.27<br>Wodim version: 1.1.9<br>SCSI buffer size: 64512<br>Beginning DMA speed test. Set CDR_NODMATEST environment variable if device<br>
communication breaks or freezes immediately after that.<br>TOC Type: 1 = CD-ROM<br>Driveropts: 'burnfree'<br>Device type : Removable CD-ROM<br>Version : 0<br>Response Format: 2<br>Capabilities : <br>Vendor_info : 'MOSER '<br>
Identification : 'BAER DH-20A4P '<br>Revision : '9M74'<br>Device seems to be: Generic mmc2 DVD-R/DVD-RW.<br>Current: 0x0009 (CD-R)<br>Profile: 0x002B (DVD+R/DL) <br>Profile: 0x001B (DVD+R) <br>Profile: 0x001A (DVD+RW) <br>
Profile: 0x0016 (DVD-R/DL layer jump recording) <br>Profile: 0x0015 (DVD-R/DL sequential recording) <br>Profile: 0x0014 (DVD-RW sequential recording) <br>Profile: 0x0013 (DVD-RW restricted overwrite) <br>Profile: 0x0012 (DVD-RAM) <br>
Profile: 0x0011 (DVD-R sequential recording) <br>Profile: 0x0010 (DVD-ROM) <br>Profile: 0x000A (CD-RW) <br>Profile: 0x0009 (CD-R) (current)<br>Profile: 0x0008 (CD-ROM) <br>Profile: 0x0002 (Removable disk) <br>Using generic SCSI-3/mmc CD-R/CD-RW driver (mmc_cdr).<br>
Driver flags : MMC-3 SWABAUDIO BURNFREE FORCESPEED <br>Supported modes: TAO PACKET SAO SAO/R96P SAO/R96R RAW/R16 RAW/R96P RAW/R96R<br>Drive buf size : 988416 = 965 KB<br>FIFO size : 12582912 = 12288 KB<br>Speed set to 1411 KB/s<br>
Track 01: data 547 MB <br>Total size: 628 MB (62:17.70) = 280328 sectors<br>Lout start: 629 MB (62:19/53) = 280328 sectors<br>Current Secsize: 2048<br>ATIP info from disk:<br> Indicated writing power: 5<br>
Is not unrestricted<br> Is not erasable<br> Disk sub type: Medium Type B, low Beta category (B-) (4)<br> ATIP start of lead in: -11834 (97:24/16)<br> ATIP start of lead out: 359849 (79:59/74)<br>Disk type: Short strategy type (Phthalocyanine or similar)<br>
Manuf. index: 24<br>Manufacturer: SONY Corporation<br>Blocks total: 359849 Blocks current: 359849 Blocks remaining: 79521<br>Forcespeed is OFF.<br>Starting to write CD/DVD at speed 8.0 in real SAO mode for single session.<br>
Last chance to quit, starting real write in 2 seconds.<br> 1 seconds.<br> 0 seconds. Operation starts.<br>Waiting for reader process to fill input buffer ... input buffer ready.<br>Performing OPC...<br>Errno: 5 (Input/output error), send opc scsi sendcmd: cmd timeout after 2.037 (200) s<br>
CDB: 54 01 00 00 00 00 00 00 00 00<br>cmd finished after 2.037s timeout 200s<br>/usr/bin/wodim: OPC failed.<br>Writing time: 2.072s<br>Errno: 5 (Input/output error), prevent/allow medium removal scsi sendcmd: retryable error<br>
CDB: 1E 00 00 00 00 00<br>status: 0x0 (GOOD STATUS)<br>cmd finished after 0.000s timeout 200s<br>Errno: 5 (Input/output error), start/stop unit scsi sendcmd: retryable error<br>CDB: 1B 00 00 00 02 00<br>status: 0x0 (GOOD STATUS)<br>
cmd finished after 0.000s timeout 200s<br>/usr/bin/wodim: Cannot eject media.<br>/usr/bin/wodim: fifo had 192 puts and 0 gets.<br>/usr/bin/wodim: fifo was 0 times empty and 0 times full, min fill was 100%.<br><br>cdrecord command:<br>
-----------------------<br>/usr/bin/wodim -v gracetime=2 dev=/dev/sr1 speed=8 -dao driveropts=burnfree -eject -data -tsize=280328s - <br><br>Once again please excuse for reporting the error properly.<br><br>sid.<br>