Bug#830992: pulseaudio: no sound with snd_hda_codec_realtek ALC880
loris
lorisdianna at yahoo.it
Wed Jul 13 15:20:38 UTC 2016
Package: pulseaudio
Version: 9.0-1.1
Severity: normal
Dear Maintainer,
on my old desktop Fujitsu Siemens Scaleo T D1826 I have installed stretch release from dvd1 (xfce desktop).
Before it there was installed jessie (gnome+xfce) and everything was running (sound was ok).
Some informations:
# lspci -vvnn
00:1b.0 Audio device [0403]: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6 Family) High Definition Audio Controller [8086:2668] (rev 03)
Subsystem: Fujitsu Technology Solutions 82801FB/FBM/FR/FW/FRW (ICH6 Family) High Definition Audio Controller [1734:1066]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 32 bytes
Interrupt: pin A routed to IRQ 24
Region 0: Memory at f0000000 (64-bit, non-prefetchable) [size=16K]
Capabilities: [50] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=55mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [60] MSI: Enable+ Count=1/1 Maskable- 64bit+
Address: 00000000fee0300c Data: 4172
Capabilities: [70] Express (v1) Root Complex Integrated Endpoint, MSI 00
DevCap: MaxPayload 128 bytes, PhantFunc 0
ExtTag- RBE-
DevCtl: Report errors: Correctable- Non-Fatal- Fatal- Unsupported-
RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop+
MaxPayload 128 bytes, MaxReadReq 128 bytes
DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr+ TransPend-
Kernel driver in use: snd_hda_intel
Kernel modules: snd_hda_intel
$ grep Codec /proc/asound/card*/codec*
Codec: Realtek ALC880
$ dmesg
[ 1178.484432] snd_hda_codec_realtek hdaudioC0D2: autoconfig for ALC880: line_outs=0 (0x0/0x0/0x0/0x0/0x0) type:line
[ 1178.484442] snd_hda_codec_realtek hdaudioC0D2: speaker_outs=0 (0x0/0x0/0x0/0x0/0x0)
[ 1178.484448] snd_hda_codec_realtek hdaudioC0D2: hp_outs=0 (0x0/0x0/0x0/0x0/0x0)
[ 1178.484454] snd_hda_codec_realtek hdaudioC0D2: mono: mono_out=0x1e
[ 1178.484459] snd_hda_codec_realtek hdaudioC0D2: inputs:
$ lsmod | grep snd
snd_hda_intel 28672 0
snd_hda_codec_realtek 61440 1
snd_hda_codec_generic 65536 1 snd_hda_codec_realtek
snd_hda_codec 94208 3 snd_hda_codec_realtek,snd_hda_codec_generic,snd_hda_intel
snd_hda_core 53248 4 snd_hda_codec_realtek,snd_hda_codec_generic,snd_hda_codec,snd_hda_intel
snd_hwdep 16384 1 snd_hda_codec
snd_pcm 86016 3 snd_hda_codec,snd_hda_intel,snd_hda_core
snd_timer 28672 1 snd_pcm
snd 57344 7 snd_hda_codec_realtek,snd_hwdep,snd_timer,snd_pcm,snd_hda_codec_generic,snd_hda_codec,snd_hda_intel
soundcore 16384 1 snd
#less /var/log/syslog
debian pulseaudio[1814]: [pulseaudio] module-alsa-card.c: Failed to find a working profile.
debian pulseaudio[1814]: [pulseaudio] module.c: Failed to load module "module-alsa-card" (argument: "device_id="0" name="pci-0000_00_1b.0" card_name="alsa_card.pci-0000_00_1b.0" namereg_fail=false tsched=yes fixed_latency_range=no ignore_dB=no deferred_volume=yes use_ucm=yes card_properties="module-udev-detect.discovered=1""): initialization failed.
2) The audio tray indicated a "dummy output"
3) same problem as root
********
-- Package-specific info:
File '/etc/default/pulseaudio' does not exist
-- System Information:
Debian Release: stretch/sid
APT prefers testing
APT policy: (500, 'testing')
Architecture: i386 (i686)
Kernel: Linux 4.6.0-1-686-pae (SMP w/2 CPU cores)
Locale: LANG=it_IT.utf8, LC_CTYPE=it_IT.utf8 (charmap=UTF-8)
Shell: /bin/sh linked to /bin/dash
Init: systemd (via /run/systemd/system)
Versions of packages pulseaudio depends on:
ii adduser 3.115
ii libasound2 1.1.1-2
ii libasound2-plugins 1.1.1-1
ii libc6 2.23-1
ii libcap2 1:2.25-1
ii libdbus-1-3 1.10.8-1
ii libfftw3-single3 3.3.4-2+b1
ii libgcc1 1:6.1.1-9
ii libice6 2:1.0.9-1+b1
ii libltdl7 2.4.6-0.1
ii liborc-0.4-0 1:0.4.25-1
ii libpulse0 9.0-1.1
ii libsm6 2:1.2.2-1+b1
ii libsndfile1 1.0.25-10
ii libsoxr0 0.1.2-1
ii libspeexdsp1 1.2~rc1.2-1
ii libstdc++6 6.1.1-9
ii libsystemd0 230-5
ii libtdb1 1.3.9-1
ii libudev1 230-5
ii libwebrtc-audio-processing1 0.3-1
ii libx11-6 2:1.6.3-1
ii libx11-xcb1 2:1.6.3-1
ii libxcb1 1.11.1-1
ii libxtst6 2:1.2.2-1+b1
ii lsb-base 9.20160629
ii pulseaudio-utils 9.0-1.1
Versions of packages pulseaudio recommends:
ii pulseaudio-module-udev 9.0-1.1
ii pulseaudio-module-x11 9.0-1.1
ii rtkit 0.11-4
Versions of packages pulseaudio suggests:
ii paman 0.9.4-1+b2
ii paprefs 0.9.10-2
ii pavucontrol 3.0-3+b2
ii pavumeter 0.9.3-4+b2
-- no debconf information
-------------- next part --------------
# This file is part of PulseAudio.
#
# PulseAudio is free software; you can redistribute it and/or modify
# it under the terms of the GNU Lesser General Public License as published by
# the Free Software Foundation; either version 2 of the License, or
# (at your option) any later version.
#
# PulseAudio is distributed in the hope that it will be useful, but
# WITHOUT ANY WARRANTY; without even the implied warranty of
# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the GNU
# General Public License for more details.
#
# You should have received a copy of the GNU Lesser General Public License
# along with PulseAudio; if not, see <http://www.gnu.org/licenses/>.
## Configuration file for PulseAudio clients. See pulse-client.conf(5) for
## more information. Default values are commented out. Use either ; or # for
## commenting.
; default-sink =
; default-source =
; default-server =
; default-dbus-server =
; autospawn = yes
; daemon-binary = /usr/bin/pulseaudio
; extra-arguments = --log-target=syslog
; cookie-file =
; enable-shm = yes
; shm-size-bytes = 0 # setting this 0 will use the system-default, usually 64 MiB
; auto-connect-localhost = no
; auto-connect-display = no
;; extra-arguments = -vvvv --log-target=newfile:/tmp/pulseverbose.log --log-time=1
-------------- next part --------------
# This file is part of PulseAudio.
#
# PulseAudio is free software; you can redistribute it and/or modify
# it under the terms of the GNU Lesser General Public License as published by
# the Free Software Foundation; either version 2 of the License, or
# (at your option) any later version.
#
# PulseAudio is distributed in the hope that it will be useful, but
# WITHOUT ANY WARRANTY; without even the implied warranty of
# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the GNU
# General Public License for more details.
#
# You should have received a copy of the GNU Lesser General Public License
# along with PulseAudio; if not, see <http://www.gnu.org/licenses/>.
## Configuration file for the PulseAudio daemon. See pulse-daemon.conf(5) for
## more information. Default values are commented out. Use either ; or # for
## commenting.
; daemonize = no
; fail = yes
; allow-module-loading = yes
; allow-exit = yes
; use-pid-file = yes
; system-instance = no
; local-server-type = user
; enable-shm = yes
; shm-size-bytes = 0 # setting this 0 will use the system-default, usually 64 MiB
; lock-memory = no
; cpu-limit = no
; high-priority = yes
; nice-level = -11
; realtime-scheduling = yes
; realtime-priority = 5
; exit-idle-time = 20
; scache-idle-time = 20
; dl-search-path = (depends on architecture)
; load-default-script-file = yes
; default-script-file = /etc/pulse/default.pa
; log-target = auto
; log-level = notice
; log-meta = no
; log-time = no
; log-backtrace = 0
; resample-method = speex-float-1
; enable-remixing = yes
; enable-lfe-remixing = no
; lfe-crossover-freq = 0
; flat-volumes = yes
; rlimit-fsize = -1
; rlimit-data = -1
; rlimit-stack = -1
; rlimit-core = -1
; rlimit-as = -1
; rlimit-rss = -1
; rlimit-nproc = -1
; rlimit-nofile = 256
; rlimit-memlock = -1
; rlimit-locks = -1
; rlimit-sigpending = -1
; rlimit-msgqueue = -1
; rlimit-nice = 31
; rlimit-rtprio = 9
; rlimit-rttime = 200000
; default-sample-format = s16le
; default-sample-rate = 44100
; alternate-sample-rate = 48000
; default-sample-channels = 2
; default-channel-map = front-left,front-right
; default-fragments = 4
; default-fragment-size-msec = 25
; enable-deferred-volume = yes
; deferred-volume-safety-margin-usec = 8000
; deferred-volume-extra-delay-usec = 0
-------------- next part --------------
#!/usr/bin/pulseaudio -nF
#
# This file is part of PulseAudio.
#
# PulseAudio is free software; you can redistribute it and/or modify it
# under the terms of the GNU Lesser General Public License as published by
# the Free Software Foundation; either version 2 of the License, or
# (at your option) any later version.
#
# PulseAudio is distributed in the hope that it will be useful, but
# WITHOUT ANY WARRANTY; without even the implied warranty of
# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the GNU
# General Public License for more details.
#
# You should have received a copy of the GNU Lesser General Public License
# along with PulseAudio; if not, see <http://www.gnu.org/licenses/>.
# This startup script is used only if PulseAudio is started per-user
# (i.e. not in system mode)
.fail
### Automatically restore the volume of streams and devices
load-module module-device-restore
load-module module-stream-restore
load-module module-card-restore
### Automatically augment property information from .desktop files
### stored in /usr/share/application
load-module module-augment-properties
### Should be after module-*-restore but before module-*-detect
load-module module-switch-on-port-available
### Load audio drivers statically
### (it's probably better to not load these drivers manually, but instead
### use module-udev-detect -- see below -- for doing this automatically)
#load-module module-alsa-sink
#load-module module-alsa-source device=hw:1,0
#load-module module-oss device="/dev/dsp" sink_name=output source_name=input
#load-module module-oss-mmap device="/dev/dsp" sink_name=output source_name=input
#load-module module-null-sink
#load-module module-pipe-sink
### Automatically load driver modules depending on the hardware available
.ifexists module-udev-detect.so
load-module module-udev-detect
.else
### Use the static hardware detection module (for systems that lack udev support)
load-module module-detect
.endif
### Automatically connect sink and source if JACK server is present
.ifexists module-jackdbus-detect.so
.nofail
load-module module-jackdbus-detect channels=2
.fail
.endif
### Automatically load driver modules for Bluetooth hardware
.ifexists module-bluetooth-policy.so
load-module module-bluetooth-policy
.endif
.ifexists module-bluetooth-discover.so
load-module module-bluetooth-discover
.endif
### Load several protocols
.ifexists module-esound-protocol-unix.so
load-module module-esound-protocol-unix
.endif
load-module module-native-protocol-unix
### Network access (may be configured with paprefs, so leave this commented
### here if you plan to use paprefs)
#load-module module-esound-protocol-tcp
#load-module module-native-protocol-tcp
#load-module module-zeroconf-publish
### Load the RTP receiver module (also configured via paprefs, see above)
#load-module module-rtp-recv
### Load the RTP sender module (also configured via paprefs, see above)
#load-module module-null-sink sink_name=rtp format=s16be channels=2 rate=44100 sink_properties="device.description='RTP Multicast Sink'"
#load-module module-rtp-send source=rtp.monitor
### Load additional modules from GConf settings. This can be configured with the paprefs tool.
### Please keep in mind that the modules configured by paprefs might conflict with manually
### loaded modules.
.ifexists module-gconf.so
.nofail
load-module module-gconf
.fail
.endif
### Automatically restore the default sink/source when changed by the user
### during runtime
### NOTE: This should be loaded as early as possible so that subsequent modules
### that look up the default sink/source get the right value
load-module module-default-device-restore
### Automatically move streams to the default sink if the sink they are
### connected to dies, similar for sources
load-module module-rescue-streams
### Make sure we always have a sink around, even if it is a null sink.
load-module module-always-sink
### Honour intended role device property
load-module module-intended-roles
### Automatically suspend sinks/sources that become idle for too long
load-module module-suspend-on-idle
### If autoexit on idle is enabled we want to make sure we only quit
### when no local session needs us anymore.
.ifexists module-console-kit.so
load-module module-console-kit
.endif
.ifexists module-systemd-login.so
load-module module-systemd-login
.endif
### Enable positioned event sounds
load-module module-position-event-sounds
### Cork music/video streams when a phone stream is active
load-module module-role-cork
### Modules to allow autoloading of filters (such as echo cancellation)
### on demand. module-filter-heuristics tries to determine what filters
### make sense, and module-filter-apply does the heavy-lifting of
### loading modules and rerouting streams.
load-module module-filter-heuristics
load-module module-filter-apply
### Make some devices default
#set-default-sink output
#set-default-source input
-------------- next part --------------
#!/usr/bin/pulseaudio -nF
#
# This file is part of PulseAudio.
#
# PulseAudio is free software; you can redistribute it and/or modify it
# under the terms of the GNU Lesser General Public License as published by
# the Free Software Foundation; either version 2 of the License, or
# (at your option) any later version.
#
# PulseAudio is distributed in the hope that it will be useful, but
# WITHOUT ANY WARRANTY; without even the implied warranty of
# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the GNU
# General Public License for more details.
#
# You should have received a copy of the GNU Lesser General Public License
# along with PulseAudio; if not, see <http://www.gnu.org/licenses/>.
# This startup script is used only if PulseAudio is started in system
# mode.
### Automatically load driver modules depending on the hardware available
.ifexists module-udev-detect.so
load-module module-udev-detect
.else
### Use the static hardware detection module (for systems that lack udev/hal support)
load-module module-detect
.endif
### Load several protocols
.ifexists module-esound-protocol-unix.so
load-module module-esound-protocol-unix
.endif
load-module module-native-protocol-unix
### Automatically restore the volume of streams and devices
load-module module-stream-restore
load-module module-device-restore
### Automatically restore the default sink/source when changed by the user
### during runtime
### NOTE: This should be loaded as early as possible so that subsequent modules
### that look up the default sink/source get the right value
load-module module-default-device-restore
### Automatically move streams to the default sink if the sink they are
### connected to dies, similar for sources
load-module module-rescue-streams
### Make sure we always have a sink around, even if it is a null sink.
load-module module-always-sink
### Automatically suspend sinks/sources that become idle for too long
load-module module-suspend-on-idle
### Enable positioned event sounds
load-module module-position-event-sounds
-------------- next part --------------
default
Playback/recording through the PulseAudio sound server
null
Discard all samples (playback) or generate zero samples (capture)
-------------- next part --------------
Module #0
Name: module-device-restore
Argument:
Usage counter: n/a
Properties:
module.author = "Lennart Poettering"
module.description = "Automatically restore the volume/mute state of devices"
module.version = "9.0"
Module #1
Name: module-stream-restore
Argument:
Usage counter: n/a
Properties:
module.author = "Lennart Poettering"
module.description = "Automatically restore the volume/mute/device state of streams"
module.version = "9.0"
Module #2
Name: module-card-restore
Argument:
Usage counter: n/a
Properties:
module.author = "Lennart Poettering"
module.description = "Automatically restore profile of cards"
module.version = "9.0"
Module #3
Name: module-augment-properties
Argument:
Usage counter: n/a
Properties:
module.author = "Lennart Poettering"
module.description = "Augment the property sets of streams with additional static information"
module.version = "9.0"
Module #4
Name: module-switch-on-port-available
Argument:
Usage counter: n/a
Properties:
Module #5
Name: module-udev-detect
Argument:
Usage counter: n/a
Properties:
module.author = "Lennart Poettering"
module.description = "Detect available audio hardware and load matching drivers"
module.version = "9.0"
Module #7
Name: module-native-protocol-unix
Argument:
Usage counter: n/a
Properties:
module.author = "Lennart Poettering"
module.description = "Native protocol (UNIX sockets)"
module.version = "9.0"
Module #8
Name: module-gconf
Argument:
Usage counter: n/a
Properties:
module.author = "Lennart Poettering"
module.description = "GConf Adapter"
module.version = "9.0"
Module #9
Name: module-default-device-restore
Argument:
Usage counter: n/a
Properties:
module.author = "Lennart Poettering"
module.description = "Automatically restore the default sink and source"
module.version = "9.0"
Module #10
Name: module-rescue-streams
Argument:
Usage counter: n/a
Properties:
module.author = "Lennart Poettering"
module.description = "When a sink/source is removed, try to move its streams to the default sink/source"
module.version = "9.0"
Module #11
Name: module-always-sink
Argument:
Usage counter: n/a
Properties:
module.author = "Colin Guthrie"
module.description = "Mantiene sempre almeno un sink caricato anche se ? nullo"
module.version = "9.0"
Module #12
Name: module-null-sink
Argument: sink_name=auto_null sink_properties='device.description="Uscita dummy"'
Usage counter: 0
Properties:
module.author = "Lennart Poettering"
module.description = "Sink NULL temporizzato"
module.version = "9.0"
Module #13
Name: module-intended-roles
Argument:
Usage counter: n/a
Properties:
module.author = "Lennart Poettering"
module.description = "Automatically set device of streams based on intended roles of devices"
module.version = "9.0"
Module #14
Name: module-suspend-on-idle
Argument:
Usage counter: n/a
Properties:
module.author = "Lennart Poettering"
module.description = "When a sink/source is idle for too long, suspend it"
module.version = "9.0"
Module #15
Name: module-console-kit
Argument:
Usage counter: n/a
Properties:
module.author = "Lennart Poettering"
module.description = "Create a client for each ConsoleKit session of this user"
module.version = "9.0"
Module #16
Name: module-systemd-login
Argument:
Usage counter: n/a
Properties:
module.author = "Lennart Poettering"
module.description = "Create a client for each login session of this user"
module.version = "9.0"
Module #17
Name: module-position-event-sounds
Argument:
Usage counter: n/a
Properties:
module.author = "Lennart Poettering"
module.description = "Position event sounds between L and R depending on the position on screen of the widget triggering them."
module.version = "9.0"
Module #18
Name: module-role-cork
Argument:
Usage counter: n/a
Properties:
module.author = "Lennart Poettering"
module.description = "Mute & cork streams with certain roles while others exist"
module.version = "9.0"
Module #19
Name: module-filter-heuristics
Argument:
Usage counter: n/a
Properties:
module.author = "Colin Guthrie"
module.description = "Detect when various filters are desirable"
module.version = "9.0"
Module #20
Name: module-filter-apply
Argument:
Usage counter: n/a
Properties:
module.author = "Colin Guthrie"
module.description = "Load filter sinks automatically when needed"
module.version = "9.0"
Module #21
Name: module-x11-publish
Argument: display=:0.0
Usage counter: n/a
Properties:
module.author = "Lennart Poettering"
module.description = "X11 credential publisher"
module.version = "9.0"
Module #22
Name: module-x11-cork-request
Argument: display=:0.0
Usage counter: n/a
Properties:
module.author = "Lennart Poettering"
module.description = "Synthesize X11 media key events when cork/uncork is requested"
module.version = "9.0"
Module #23
Name: module-x11-xsmp
Argument: display=:0.0 session_manager=local/debian:@/tmp/.ICE-unix/1747,unix/debian:/tmp/.ICE-unix/1747
Usage counter: n/a
Properties:
module.author = "Lennart Poettering"
module.description = "X11 session management"
module.version = "9.0"
Sink #0
State: SUSPENDED
Name: auto_null
Description: Uscita dummy
Driver: module-null-sink.c
Sample Specification: s16le 2ch 44100Hz
Channel Map: front-left,front-right
Owner Module: 12
Mute: no
Volume: front-left: 39322 / 60% / -13.31 dB, front-right: 39322 / 60% / -13.31 dB
balance 0.00
Base Volume: 65536 / 100% / 0.00 dB
Monitor Source: auto_null.monitor
Latency: 0 usec, configured 0 usec
Flags: DECIBEL_VOLUME LATENCY
Properties:
device.description = "Uscita dummy"
device.class = "abstract"
device.icon_name = "audio-card"
Formats:
pcm
Source #0
State: SUSPENDED
Name: auto_null.monitor
Description: Monitor of Uscita dummy
Driver: module-null-sink.c
Sample Specification: s16le 2ch 44100Hz
Channel Map: front-left,front-right
Owner Module: 12
Mute: no
Volume: front-left: 65536 / 100% / 0.00 dB, front-right: 65536 / 100% / 0.00 dB
balance 0.00
Base Volume: 65536 / 100% / 0.00 dB
Monitor of Sink: auto_null
Latency: 0 usec, configured 0 usec
Flags: DECIBEL_VOLUME LATENCY
Properties:
device.description = "Monitor of Uscita dummy"
device.class = "monitor"
device.icon_name = "audio-input-microphone"
Formats:
pcm
Client #0
Driver: module-systemd-login.c
Owner Module: 16
Properties:
application.name = "Login Session 2"
systemd-login.session = "2"
Client #1
Driver: protocol-native.c
Owner Module: 7
Properties:
application.name = "xfce4-pulseaudio-plugin"
native-protocol.peer = "UNIX socket client"
native-protocol.version = "31"
application.version = "0.2.4"
application.id = "org.xfce.pulseaudio-plugin"
application.icon_name = "multimedia-volume-control"
application.process.id = "1847"
application.process.user = "lac"
application.process.host = "debian"
application.process.binary = "wrapper-2.0"
application.language = "it_IT.utf8"
window.x11.display = ":0.0"
application.process.machine_id = "20481986835b485c91338460cc512374"
application.process.session_id = "2"
Client #5
Driver: module-x11-xsmp.c
Owner Module: 23
Properties:
application.name = "XSMP Session on xfce4-session as 219da20ac-8b98-4200-8bea-be2d3e50f6d2"
xsmp.vendor = "xfce4-session"
xsmp.client.id = "219da20ac-8b98-4200-8bea-be2d3e50f6d2"
Client #20
Driver: protocol-native.c
Owner Module: 7
Properties:
application.name = "pactl"
native-protocol.peer = "UNIX socket client"
native-protocol.version = "31"
application.process.id = "2225"
application.process.user = "lac"
application.process.host = "debian"
application.process.binary = "pactl"
application.language = "C"
window.x11.display = ":0.0"
application.process.machine_id = "20481986835b485c91338460cc512374"
application.process.session_id = "2"
-------------- next part --------------
Server String: unix:/run/user/1000/pulse/native
Library Protocol Version: 31
Server Protocol Version: 31
Is Local: yes
Client Index: 21
Tile Size: 65496
User Name: lac
Host Name: debian
Server Name: pulseaudio
Server Version: 9.0
Default Sample Specification: s16le 2ch 44100Hz
Default Channel Map: front-left,front-right
Default Sink: auto_null
Default Source: auto_null.monitor
Cookie: 44dc:5207
More information about the pkg-pulseaudio-devel
mailing list