[Pkg-utopia-maintainers] Bug#544217: Bug#544217: Bug#544217: network-manager: "wireless is disabled" message
Sam Morris
sam at robots.org.uk
Sun Aug 30 16:50:31 UTC 2009
affects 544319 network-manager
affects 544321 network-manager
block 544217 by 544319
block 544217 by 544321
thanks
On Sun, 2009-08-30 at 14:03 +0200, Michael Biebl wrote:
> If the rfkill state is not correctly detected, it's more likely a problem of
> hal, so you might start checking there first.
The applet makes the following dbus call to find out if the wireless
hardware is disabled:
$ dbus-send --print-reply --system --dest=org.freedesktop.NetworkManager /org/freedesktop/NetworkManager org.freedesktop.NetworkManager.getWirelessEnabled
method return sender=:1.98 -> dest=:1.237 reply_serial=2
boolean false
boolean false
These two values correspond to the wireless_enabled and hw_rf_enabled
values from NetworkManager. These values are populated based on stuff
from HAL.
$ hal-find-by-capability --capability killswitch | while read line; do echo $line; dbus-send --system --print-reply --dest=org.freedesktop.Hal $line org.freedesktop.Hal.Device.KillSwitch.GetPower; done
/org/freedesktop/Hal/devices/computer_rfkill_dell_wifi_wlan
method return sender=:1.103 -> dest=:1.285 reply_serial=2
int32 0
/org/freedesktop/Hal/devices/pci_8086_4232_rfkill_5100AGN_wlan
method return sender=:1.103 -> dest=:1.287 reply_serial=2
int32 1
/org/freedesktop/Hal/devices/dell_wlan_switch
int32 0
According to the HAL spec, GetPower returns 1 iff the power to the radio
is on.
At this point I took a closer look at these three killswitch devices.
The full output of 'lshal' is attached to the original bug report.
The first device is an rfkill device. If I read
/sys/devices/virtual/rfkill/rfkill0/state then I get back '2', meaning
that the radio has been disabled in hardware--incorrect! If I remove the
dell_wireless kernel module then this device disappears. Bug #544319
filed.
The second device is another rfkill device, and it seems to work
fine--its state is '1' which means the radio is on.
The third device has its 'killswitch.access_method' set to 'dell', which
causes HAL to run the dellWirelessCtl program:
$ dellWirelessCtl --st_wlan; echo $?
Radio Status for WLAN:
WLAN supported
WLAN installed
WLAN disabled
Status Code: 1
1
Bug #544321 filed.
There are a few options for working around these bugs. I list them ehre
for the benefit of other users with the same problem:
1. Tell HAL to ignore all rfkill devices. I tried to do this by
setting the 'info.ignore' property on each of the killswitch
devices. Unfortunately, this didn't stop NetworkManager from
seeing them. I guess info.ignore isn't supposed to be used for
this purpose. Is there another way to deal with this at the HAL
level?
2. Patch NetworkManager to override the information coming from
HAL. The 'nm-ignore-killswitches.patch' is attached, and it does
work. Of course, it's not suitable as anything other than a
crude hack to workaround the issue.
3. Fix the broken killswitch devices. The first broken device comes
from the kernel's dell_laptop module, so that's one bug. The
second comes from HAL's device database, but is actually queried
with the dellWirelessCtl utility, which returns the wrong
result. I have filed separate bugs for these issues.
4. Work around the broken killswitch devices. The dell_laptop
kernel module can simply be blacklisted, and removing the
libsmbios-bin package that contains dellWirelessCtl causes
querying HAL for its status to return an error; which in turn
causes NetworkManager to assume that the radio is enabled.
5. Fix the hardware. Dell have posted a BIOS update for my laptop,
version A03, the release notes of which include "Fix kill switch
sttatus report fail". Unfortunately, it is impossible to
actually install this update without installing Windows, so I
can't test that out. :(
BTW, I booted the Ubuntu 9.04 LiveCD and wireless worked fine. I ran
lshal (output attached) and noticed that they don't have the broken
computer_rfkill_dell_wifi_wlan device. Maybe this is because they have
some super secret fixes in their packages, or maybe it's because this is
a bug in a later kernel than their 2.6.28 kernel (or they don't build
the dell_laptop kernel module).
--
Sam Morris
https://robots.org.uk/
PGP key id 1024D/5EA01078
3412 EA18 1277 354B 991B C869 B219 7FDB 5EA0 1078
-------------- next part --------------
Dumping 123 device(s) from the Global Device List:
-------------------------------------------------
udi = '/org/freedesktop/Hal/devices/computer'
info.addons = {'hald-addon-cpufreq', 'hald-addon-acpi'} (string list)
info.callouts.add = {'hal-acl-tool --remove-all', 'hal-storage-cleanup-all-mountpoints'} (string list)
info.callouts.session_active = {'hal-acl-tool --reconfigure'} (string list)
info.callouts.session_add = {'hal-acl-tool --reconfigure'} (string list)
info.callouts.session_inactive = {'hal-acl-tool --reconfigure'} (string list)
info.callouts.session_remove = {'hal-acl-tool --reconfigure'} (string list)
info.capabilities = {'cpufreq_control'} (string list)
info.interfaces = {'org.freedesktop.Hal.Device.SystemPowerManagement', 'org.freedesktop.Hal.Device.CPUFreq'} (string list)
info.product = 'Computer' (string)
info.subsystem = 'unknown' (string)
info.udi = '/org/freedesktop/Hal/devices/computer' (string)
org.freedesktop.Hal.Device.SystemPowerManagement.method_argnames = {'num_seconds_to_sleep', 'num_seconds_to_sleep', '', '', '', 'enable_power_save'} (string list)
org.freedesktop.Hal.Device.SystemPowerManagement.method_execpaths = {'hal-system-power-suspend', 'hal-system-power-suspend-hybrid', 'hal-system-power-hibernate', 'hal-system-power-shutdown', 'hal-system-power-reboot', 'hal-system-power-set-power-save'} (string list)
org.freedesktop.Hal.Device.SystemPowerManagement.method_names = {'Suspend', 'SuspendHybrid', 'Hibernate', 'Shutdown', 'Reboot', 'SetPowerSave'} (string list)
org.freedesktop.Hal.Device.SystemPowerManagement.method_signatures = {'i', 'i', '', '', '', 'b'} (string list)
power_management.acpi.linux.version = '20080926' (string)
power_management.can_hibernate = true (bool)
power_management.can_suspend = true (bool)
power_management.can_suspend_hybrid = false (bool)
power_management.is_powersave_set = false (bool)
power_management.quirk.dpms_on = true (bool)
power_management.quirk.dpms_suspend = true (bool)
power_management.quirk.vbe_post = true (bool)
power_management.quirk.vbemode_restore = true (bool)
power_management.quirk.vbestate_restore = true (bool)
power_management.quirk.vga_mode_3 = true (bool)
power_management.type = 'acpi' (string)
system.board.product = '0T816J' (string)
system.board.serial = '.BZ6GQK1.CN1296198I0061.' (string)
system.board.vendor = 'Dell Inc.' (string)
system.board.version = '' (string)
system.chassis.manufacturer = 'Dell Inc.' (string)
system.chassis.type = 'Portable' (string)
system.firmware.release_date = '04/08/2009' (string)
system.firmware.vendor = 'Dell Inc.' (string)
system.firmware.version = 'A02' (string)
system.formfactor = 'laptop' (string)
system.hardware.primary_video.product = 10818 (0x2a42) (int)
system.hardware.primary_video.vendor = 32902 (0x8086) (int)
system.hardware.product = 'Vostro 1520' (string)
system.hardware.serial = 'BZ6GQK1' (string)
system.hardware.uuid = '' (string)
system.hardware.vendor = 'Dell Inc.' (string)
system.hardware.version = 'Null' (string)
system.kernel.machine = 'i686' (string)
system.kernel.name = 'Linux' (string)
system.kernel.version = '2.6.28-11-generic' (string)
system.kernel.version.major = 2 (0x2) (int)
system.kernel.version.micro = 28 (0x1c) (int)
system.kernel.version.minor = 6 (0x6) (int)
udi = '/org/freedesktop/Hal/devices/net_26_ae_2c_fa_f4_13'
info.capabilities = {'net', 'net.bridge'} (string list)
info.category = 'net.bridge' (string)
info.parent = '/org/freedesktop/Hal/devices/computer' (string)
info.product = 'Bridge Interface' (string)
info.subsystem = 'net' (string)
info.udi = '/org/freedesktop/Hal/devices/net_26_ae_2c_fa_f4_13' (string)
linux.hotplug_type = 2 (0x2) (int)
linux.subsystem = 'net' (string)
linux.sysfs_path = '/sys/devices/virtual/net/pan0' (string)
net.address = '26:ae:2c:fa:f4:13' (string)
net.arp_proto_hw_id = 1 (0x1) (int)
net.bridge.mac_address = 42529520808979 (0x26ae2cfaf413) (uint64)
net.interface = 'pan0' (string)
net.linux.ifindex = 5 (0x5) (int)
net.originating_device = '/org/freedesktop/Hal/devices/computer' (string)
udi = '/org/freedesktop/Hal/devices/computer_logicaldev_input_4'
button.has_state = true (bool)
button.state.value = false (bool)
button.type = 'lid' (string)
info.addons.singleton = {'hald-addon-input'} (string list)
info.capabilities = {'input', 'input.switch', 'button'} (string list)
info.category = 'input' (string)
info.parent = '/org/freedesktop/Hal/devices/computer' (string)
info.product = 'Lid Switch' (string)
info.subsystem = 'input' (string)
info.udi = '/org/freedesktop/Hal/devices/computer_logicaldev_input_4' (string)
input.device = '/dev/input/event1' (string)
input.product = 'Lid Switch' (string)
linux.device_file = '/dev/input/event1' (string)
linux.hotplug_type = 2 (0x2) (int)
linux.subsystem = 'input' (string)
linux.sysfs_path = '/sys/devices/LNXSYSTM:00/device:00/PNP0C0D:00/input/input1/event1' (string)
udi = '/org/freedesktop/Hal/devices/computer_logicaldev_input_0'
info.addons.singleton = {'hald-addon-input'} (string list)
info.callouts.add = {'debian-setup-keyboard'} (string list)
info.capabilities = {'input', 'input.keys', 'button'} (string list)
info.category = 'input' (string)
info.parent = '/org/freedesktop/Hal/devices/computer' (string)
info.product = 'Video Bus' (string)
info.subsystem = 'input' (string)
info.udi = '/org/freedesktop/Hal/devices/computer_logicaldev_input_0' (string)
input.device = '/dev/input/event6' (string)
input.product = 'Video Bus' (string)
input.x11_driver = 'evdev' (string)
input.xkb.layout = 'us' (string)
input.xkb.model = 'pc105' (string)
input.xkb.rules = 'evdev' (string)
linux.device_file = '/dev/input/event6' (string)
linux.hotplug_type = 2 (0x2) (int)
linux.subsystem = 'input' (string)
linux.sysfs_path = '/sys/devices/LNXSYSTM:00/device:00/PNP0A08:00/device:06/input/input6/event6' (string)
udi = '/org/freedesktop/Hal/devices/computer_alsa_timer'
access_control.file = '/dev/snd/timer' (string)
access_control.type = 'sound' (string)
alsa.device_file = '/dev/snd/timer' (string)
alsa.type = 'timer' (string)
info.callouts.add = {'hal-acl-tool --add-device'} (string list)
info.callouts.remove = {'hal-acl-tool --remove-device'} (string list)
info.capabilities = {'alsa', 'access_control'} (string list)
info.category = 'alsa' (string)
info.parent = '/org/freedesktop/Hal/devices/computer' (string)
info.product = 'ALSA Timer Device' (string)
info.subsystem = 'sound' (string)
info.udi = '/org/freedesktop/Hal/devices/computer_alsa_timer' (string)
linux.device_file = '/dev/snd/timer' (string)
linux.hotplug_type = 2 (0x2) (int)
linux.subsystem = 'sound' (string)
linux.sysfs_path = '/sys/devices/virtual/sound/timer' (string)
udi = '/org/freedesktop/Hal/devices/computer_oss_sequencer_0'
access_control.file = '/dev/sequencer2' (string)
access_control.type = 'sound' (string)
info.callouts.add = {'hal-acl-tool --add-device'} (string list)
info.callouts.remove = {'hal-acl-tool --remove-device'} (string list)
info.capabilities = {'oss', 'access_control'} (string list)
info.category = 'oss' (string)
info.parent = '/org/freedesktop/Hal/devices/computer' (string)
info.product = 'OSS Sequencer Device' (string)
info.subsystem = 'sound' (string)
info.udi = '/org/freedesktop/Hal/devices/computer_oss_sequencer_0' (string)
linux.device_file = '/dev/sequencer2' (string)
linux.hotplug_type = 2 (0x2) (int)
linux.subsystem = 'sound' (string)
linux.sysfs_path = '/sys/devices/virtual/sound/sequencer2' (string)
oss.device_file = '/dev/sequencer2' (string)
oss.type = 'sequencer' (string)
udi = '/org/freedesktop/Hal/devices/computer_alsa_sequencer'
access_control.file = '/dev/snd/seq' (string)
access_control.type = 'sound' (string)
alsa.device_file = '/dev/snd/seq' (string)
alsa.type = 'sequencer' (string)
info.callouts.add = {'hal-acl-tool --add-device'} (string list)
info.callouts.remove = {'hal-acl-tool --remove-device'} (string list)
info.capabilities = {'alsa', 'access_control'} (string list)
info.category = 'alsa' (string)
info.parent = '/org/freedesktop/Hal/devices/computer' (string)
info.product = 'ALSA Sequencer Device' (string)
info.subsystem = 'sound' (string)
info.udi = '/org/freedesktop/Hal/devices/computer_alsa_sequencer' (string)
linux.device_file = '/dev/snd/seq' (string)
linux.hotplug_type = 2 (0x2) (int)
linux.subsystem = 'sound' (string)
linux.sysfs_path = '/sys/devices/virtual/sound/seq' (string)
udi = '/org/freedesktop/Hal/devices/computer_oss_sequencer'
access_control.file = '/dev/sequencer' (string)
access_control.type = 'sound' (string)
info.callouts.add = {'hal-acl-tool --add-device'} (string list)
info.callouts.remove = {'hal-acl-tool --remove-device'} (string list)
info.capabilities = {'oss', 'access_control'} (string list)
info.category = 'oss' (string)
info.parent = '/org/freedesktop/Hal/devices/computer' (string)
info.product = 'OSS Sequencer Device' (string)
info.subsystem = 'sound' (string)
info.udi = '/org/freedesktop/Hal/devices/computer_oss_sequencer' (string)
linux.device_file = '/dev/sequencer' (string)
linux.hotplug_type = 2 (0x2) (int)
linux.subsystem = 'sound' (string)
linux.sysfs_path = '/sys/devices/virtual/sound/sequencer' (string)
oss.device_file = '/dev/sequencer' (string)
oss.type = 'sequencer' (string)
udi = '/org/freedesktop/Hal/devices/computer_logicaldev_input_3'
access_control.file = '/dev/input/event4' (string)
access_control.type = 'mouse' (string)
info.callouts.add = {'hal-acl-tool --add-device'} (string list)
info.callouts.remove = {'hal-acl-tool --remove-device'} (string list)
info.capabilities = {'input', 'input.mouse', 'access_control'} (string list)
info.category = 'input' (string)
info.parent = '/org/freedesktop/Hal/devices/computer' (string)
info.product = 'Macintosh mouse button emulation' (string)
info.subsystem = 'input' (string)
info.udi = '/org/freedesktop/Hal/devices/computer_logicaldev_input_3' (string)
input.device = '/dev/input/event4' (string)
input.product = 'Macintosh mouse button emulation' (string)
input.x11_driver = 'evdev' (string)
linux.device_file = '/dev/input/event4' (string)
linux.hotplug_type = 2 (0x2) (int)
linux.subsystem = 'input' (string)
linux.sysfs_path = '/sys/devices/virtual/input/input4/event4' (string)
udi = '/org/freedesktop/Hal/devices/acpi_CPU0'
info.capabilities = {'processor'} (string list)
info.category = 'processor' (string)
info.parent = '/org/freedesktop/Hal/devices/computer' (string)
info.product = 'Intel(R) Core(TM)2 Duo CPU T6670 @ 2.20GHz' (string)
info.udi = '/org/freedesktop/Hal/devices/acpi_CPU0' (string)
linux.acpi_path = '/proc/acpi/processor/CPU0' (string)
linux.acpi_type = 1 (0x1) (int)
linux.hotplug_type = 4 (0x4) (int)
processor.can_throttle = false (bool)
processor.number = 0 (0x0) (int)
udi = '/org/freedesktop/Hal/devices/acpi_CPU1'
info.capabilities = {'processor'} (string list)
info.category = 'processor' (string)
info.parent = '/org/freedesktop/Hal/devices/computer' (string)
info.product = 'Intel(R) Core(TM)2 Duo CPU T6670 @ 2.20GHz' (string)
info.udi = '/org/freedesktop/Hal/devices/acpi_CPU1' (string)
linux.acpi_path = '/proc/acpi/processor/CPU1' (string)
linux.acpi_type = 1 (0x1) (int)
linux.hotplug_type = 4 (0x4) (int)
processor.can_throttle = false (bool)
processor.number = 1 (0x1) (int)
udi = '/org/freedesktop/Hal/devices/net_computer_loopback'
info.capabilities = {'net', 'net.loopback'} (string list)
info.category = 'net.loopback' (string)
info.parent = '/org/freedesktop/Hal/devices/computer' (string)
info.product = 'Loopback device Interface' (string)
info.subsystem = 'net' (string)
info.udi = '/org/freedesktop/Hal/devices/net_computer_loopback' (string)
linux.hotplug_type = 2 (0x2) (int)
linux.subsystem = 'net' (string)
linux.sysfs_path = '/sys/devices/virtual/net/lo' (string)
net.address = '00:00:00:00:00:00' (string)
net.arp_proto_hw_id = 772 (0x304) (int)
net.interface = 'lo' (string)
net.linux.ifindex = 1 (0x1) (int)
net.originating_device = '/org/freedesktop/Hal/devices/computer' (string)
udi = '/org/freedesktop/Hal/devices/computer_backlight'
info.addons = {'hald-addon-generic-backlight'} (string list)
info.capabilities = {'laptop_panel'} (string list)
info.category = 'laptop_panel' (string)
info.interfaces = {'org.freedesktop.Hal.Device.LaptopPanel'} (string list)
info.parent = '/org/freedesktop/Hal/devices/computer' (string)
info.product = 'Generic Backlight Device' (string)
info.subsystem = 'backlight' (string)
info.udi = '/org/freedesktop/Hal/devices/computer_backlight' (string)
laptop_panel.access_method = 'general' (string)
laptop_panel.brightness_in_hardware = false (bool)
laptop_panel.num_levels = 8 (0x8) (int)
linux.hotplug_type = 2 (0x2) (int)
linux.subsystem = 'backlight' (string)
linux.sysfs_path = '/sys/devices/virtual/backlight/acpi_video0' (string)
udi = '/org/freedesktop/Hal/devices/computer_logicaldev_input_2'
button.has_state = false (bool)
button.type = 'sleep' (string)
info.addons.singleton = {'hald-addon-input'} (string list)
info.capabilities = {'input', 'button'} (string list)
info.category = 'input' (string)
info.parent = '/org/freedesktop/Hal/devices/computer' (string)
info.product = 'Sleep Button (CM)' (string)
info.subsystem = 'input' (string)
info.udi = '/org/freedesktop/Hal/devices/computer_logicaldev_input_2' (string)
input.device = '/dev/input/event3' (string)
input.product = 'Sleep Button (CM)' (string)
linux.device_file = '/dev/input/event3' (string)
linux.hotplug_type = 2 (0x2) (int)
linux.subsystem = 'input' (string)
linux.sysfs_path = '/sys/devices/LNXSYSTM:00/device:00/PNP0C0E:00/input/input3/event3' (string)
udi = '/org/freedesktop/Hal/devices/computer_logicaldev_input_1'
button.has_state = false (bool)
button.type = 'power' (string)
info.addons.singleton = {'hald-addon-input'} (string list)
info.capabilities = {'input', 'button'} (string list)
info.category = 'input' (string)
info.parent = '/org/freedesktop/Hal/devices/computer' (string)
info.product = 'Power Button (CM)' (string)
info.subsystem = 'input' (string)
info.udi = '/org/freedesktop/Hal/devices/computer_logicaldev_input_1' (string)
input.device = '/dev/input/event2' (string)
input.product = 'Power Button (CM)' (string)
linux.device_file = '/dev/input/event2' (string)
linux.hotplug_type = 2 (0x2) (int)
linux.subsystem = 'input' (string)
linux.sysfs_path = '/sys/devices/LNXSYSTM:00/device:00/PNP0C0C:00/input/input2/event2' (string)
udi = '/org/freedesktop/Hal/devices/computer_power_supply_battery_BAT1'
battery.charge_level.current = 57720 (0xe178) (int)
battery.charge_level.design = 57720 (0xe178) (int)
battery.charge_level.last_full = 57720 (0xe178) (int)
battery.charge_level.percentage = 100 (0x64) (int)
battery.charge_level.rate = 0 (0x0) (int)
battery.is_rechargeable = true (bool)
battery.model = '' (string)
battery.present = true (bool)
battery.rechargeable.is_charging = false (bool)
battery.rechargeable.is_discharging = false (bool)
battery.reporting.current = 57720 (0xe178) (int)
battery.reporting.design = 57720 (0xe178) (int)
battery.reporting.last_full = 57720 (0xe178) (int)
battery.reporting.rate = 0 (0x0) (int)
battery.reporting.technology = 'Li-ion' (string)
battery.reporting.unit = 'mWh' (string)
battery.serial = '11' (string)
battery.technology = 'lithium-ion' (string)
battery.type = 'primary' (string)
battery.vendor = 'Dell' (string)
battery.voltage.current = 12494 (0x30ce) (int)
battery.voltage.design = 11100 (0x2b5c) (int)
battery.voltage.unit = 'mV' (string)
info.capabilities = {'battery'} (string list)
info.category = 'battery' (string)
info.parent = '/org/freedesktop/Hal/devices/computer' (string)
info.product = '' (string)
info.subsystem = 'power_supply' (string)
info.udi = '/org/freedesktop/Hal/devices/computer_power_supply_battery_BAT1' (string)
linux.hotplug_type = 2 (0x2) (int)
linux.subsystem = 'power_supply' (string)
linux.sysfs_path = '/sys/devices/LNXSYSTM:00/device:00/PNP0A08:00/device:0d/PNP0C0A:00/power_supply/BAT1' (string)
udi = '/org/freedesktop/Hal/devices/computer_power_supply_ac_adapter_ACAD'
ac_adapter.present = true (bool)
info.capabilities = {'ac_adapter'} (string list)
info.category = 'ac_adapter' (string)
info.parent = '/org/freedesktop/Hal/devices/computer' (string)
info.product = 'Generic AC Adapter Device' (string)
info.subsystem = 'power_supply' (string)
info.udi = '/org/freedesktop/Hal/devices/computer_power_supply_ac_adapter_ACAD' (string)
linux.hotplug_type = 2 (0x2) (int)
linux.subsystem = 'power_supply' (string)
linux.sysfs_path = '/sys/devices/LNXSYSTM:00/device:00/PNP0A08:00/device:0d/ACPI0003:00/power_supply/ACAD' (string)
udi = '/org/freedesktop/Hal/devices/computer_logicaldev_input'
button.has_state = false (bool)
button.type = 'power' (string)
info.addons.singleton = {'hald-addon-input'} (string list)
info.capabilities = {'input', 'button'} (string list)
info.category = 'input' (string)
info.parent = '/org/freedesktop/Hal/devices/computer' (string)
info.product = 'Power Button (FF)' (string)
info.subsystem = 'input' (string)
info.udi = '/org/freedesktop/Hal/devices/computer_logicaldev_input' (string)
input.device = '/dev/input/event0' (string)
input.product = 'Power Button (FF)' (string)
linux.device_file = '/dev/input/event0' (string)
linux.hotplug_type = 2 (0x2) (int)
linux.subsystem = 'input' (string)
linux.sysfs_path = '/sys/devices/LNXSYSTM:00/LNXPWRBN:00/input/input0/event0' (string)
udi = '/org/freedesktop/Hal/devices/pnp_PNP0c02_1'
info.linux.driver = 'system' (string)
info.parent = '/org/freedesktop/Hal/devices/computer' (string)
info.product = 'General ID for reserving resources required by PnP motherboard registers. (Not device specific.)' (string)
info.subsystem = 'pnp' (string)
info.udi = '/org/freedesktop/Hal/devices/pnp_PNP0c02_1' (string)
linux.hotplug_type = 2 (0x2) (int)
linux.subsystem = 'pnp' (string)
linux.sysfs_path = '/sys/devices/pnp0/00:09' (string)
pnp.description = 'General ID for reserving resources required by PnP motherboard registers. (Not device specific.)' (string)
pnp.id = 'PNP0c02' (string)
udi = '/org/freedesktop/Hal/devices/pnp_PNP0c02_0'
info.linux.driver = 'system' (string)
info.parent = '/org/freedesktop/Hal/devices/computer' (string)
info.product = 'General ID for reserving resources required by PnP motherboard registers. (Not device specific.)' (string)
info.subsystem = 'pnp' (string)
info.udi = '/org/freedesktop/Hal/devices/pnp_PNP0c02_0' (string)
linux.hotplug_type = 2 (0x2) (int)
linux.subsystem = 'pnp' (string)
linux.sysfs_path = '/sys/devices/pnp0/00:08' (string)
pnp.description = 'General ID for reserving resources required by PnP motherboard registers. (Not device specific.)' (string)
pnp.id = 'PNP0c02' (string)
udi = '/org/freedesktop/Hal/devices/pnp_SYN070b'
info.linux.driver = 'i8042 aux' (string)
info.parent = '/org/freedesktop/Hal/devices/computer' (string)
info.product = 'PnP Device (SYN070b)' (string)
info.subsystem = 'pnp' (string)
info.udi = '/org/freedesktop/Hal/devices/pnp_SYN070b' (string)
linux.hotplug_type = 2 (0x2) (int)
linux.subsystem = 'pnp' (string)
linux.sysfs_path = '/sys/devices/pnp0/00:07' (string)
pnp.id = 'SYN070b' (string)
udi = '/org/freedesktop/Hal/devices/pnp_PNP0303'
info.linux.driver = 'i8042 kbd' (string)
info.parent = '/org/freedesktop/Hal/devices/computer' (string)
info.product = 'IBM Enhanced (101/102-key, PS/2 mouse support)' (string)
info.subsystem = 'pnp' (string)
info.udi = '/org/freedesktop/Hal/devices/pnp_PNP0303' (string)
linux.hotplug_type = 2 (0x2) (int)
linux.subsystem = 'pnp' (string)
linux.sysfs_path = '/sys/devices/pnp0/00:06' (string)
pnp.description = 'IBM Enhanced (101/102-key, PS/2 mouse support)' (string)
pnp.id = 'PNP0303' (string)
udi = '/org/freedesktop/Hal/devices/pnp_PNP0b00'
info.linux.driver = 'rtc_cmos' (string)
info.parent = '/org/freedesktop/Hal/devices/computer' (string)
info.product = 'AT Real-Time Clock' (string)
info.subsystem = 'pnp' (string)
info.udi = '/org/freedesktop/Hal/devices/pnp_PNP0b00' (string)
linux.hotplug_type = 2 (0x2) (int)
linux.subsystem = 'pnp' (string)
linux.sysfs_path = '/sys/devices/pnp0/00:05' (string)
pnp.description = 'AT Real-Time Clock' (string)
pnp.id = 'PNP0b00' (string)
udi = '/org/freedesktop/Hal/devices/pnp_PNP0c02'
info.linux.driver = 'system' (string)
info.parent = '/org/freedesktop/Hal/devices/computer' (string)
info.product = 'General ID for reserving resources required by PnP motherboard registers. (Not device specific.)' (string)
info.subsystem = 'pnp' (string)
info.udi = '/org/freedesktop/Hal/devices/pnp_PNP0c02' (string)
linux.hotplug_type = 2 (0x2) (int)
linux.subsystem = 'pnp' (string)
linux.sysfs_path = '/sys/devices/pnp0/00:04' (string)
pnp.description = 'General ID for reserving resources required by PnP motherboard registers. (Not device specific.)' (string)
pnp.id = 'PNP0c02' (string)
udi = '/org/freedesktop/Hal/devices/pnp_PNP0c04'
info.parent = '/org/freedesktop/Hal/devices/computer' (string)
info.product = 'Math Coprocessor' (string)
info.subsystem = 'pnp' (string)
info.udi = '/org/freedesktop/Hal/devices/pnp_PNP0c04' (string)
linux.hotplug_type = 2 (0x2) (int)
linux.subsystem = 'pnp' (string)
linux.sysfs_path = '/sys/devices/pnp0/00:03' (string)
pnp.description = 'Math Coprocessor' (string)
pnp.id = 'PNP0c04' (string)
udi = '/org/freedesktop/Hal/devices/pnp_PNP0103'
info.linux.driver = 'system' (string)
info.parent = '/org/freedesktop/Hal/devices/computer' (string)
info.product = 'PnP Device (PNP0103)' (string)
info.subsystem = 'pnp' (string)
info.udi = '/org/freedesktop/Hal/devices/pnp_PNP0103' (string)
linux.hotplug_type = 2 (0x2) (int)
linux.subsystem = 'pnp' (string)
linux.sysfs_path = '/sys/devices/pnp0/00:02' (string)
pnp.id = 'PNP0103' (string)
udi = '/org/freedesktop/Hal/devices/pnp_PNP0200'
info.parent = '/org/freedesktop/Hal/devices/computer' (string)
info.product = 'AT DMA Controller' (string)
info.subsystem = 'pnp' (string)
info.udi = '/org/freedesktop/Hal/devices/pnp_PNP0200' (string)
linux.hotplug_type = 2 (0x2) (int)
linux.subsystem = 'pnp' (string)
linux.sysfs_path = '/sys/devices/pnp0/00:01' (string)
pnp.description = 'AT DMA Controller' (string)
pnp.id = 'PNP0200' (string)
udi = '/org/freedesktop/Hal/devices/pnp_PNP0a08'
info.parent = '/org/freedesktop/Hal/devices/computer' (string)
info.product = 'PnP Device (PNP0a08)' (string)
info.subsystem = 'pnp' (string)
info.udi = '/org/freedesktop/Hal/devices/pnp_PNP0a08' (string)
linux.hotplug_type = 2 (0x2) (int)
linux.subsystem = 'pnp' (string)
linux.sysfs_path = '/sys/devices/pnp0/00:00' (string)
pnp.id = 'PNP0a08' (string)
udi = '/org/freedesktop/Hal/devices/platform_serial8250'
info.linux.driver = 'serial8250' (string)
info.parent = '/org/freedesktop/Hal/devices/computer' (string)
info.product = 'Platform Device (serial8250)' (string)
info.subsystem = 'platform' (string)
info.udi = '/org/freedesktop/Hal/devices/platform_serial8250' (string)
linux.hotplug_type = 2 (0x2) (int)
linux.subsystem = 'platform' (string)
linux.sysfs_path = '/sys/devices/platform/serial8250' (string)
platform.id = 'serial8250' (string)
udi = '/org/freedesktop/Hal/devices/platform_regulatory_0'
info.parent = '/org/freedesktop/Hal/devices/computer' (string)
info.product = 'Platform Device (regulatory.0)' (string)
info.subsystem = 'platform' (string)
info.udi = '/org/freedesktop/Hal/devices/platform_regulatory_0' (string)
linux.hotplug_type = 2 (0x2) (int)
linux.subsystem = 'platform' (string)
linux.sysfs_path = '/sys/devices/platform/regulatory.0' (string)
platform.id = 'regulatory.0' (string)
udi = '/org/freedesktop/Hal/devices/platform_pcspkr'
info.linux.driver = 'pcspkr' (string)
info.parent = '/org/freedesktop/Hal/devices/computer' (string)
info.product = 'Platform Device (pcspkr)' (string)
info.subsystem = 'platform' (string)
info.udi = '/org/freedesktop/Hal/devices/platform_pcspkr' (string)
linux.hotplug_type = 2 (0x2) (int)
linux.subsystem = 'platform' (string)
linux.sysfs_path = '/sys/devices/platform/pcspkr' (string)
platform.id = 'pcspkr' (string)
udi = '/org/freedesktop/Hal/devices/platform_pcspkr_logicaldev_input'
info.capabilities = {'input'} (string list)
info.category = 'input' (string)
info.parent = '/org/freedesktop/Hal/devices/platform_pcspkr' (string)
info.product = 'PC Speaker' (string)
info.subsystem = 'input' (string)
info.udi = '/org/freedesktop/Hal/devices/platform_pcspkr_logicaldev_input' (string)
input.device = '/dev/input/event7' (string)
input.originating_device = '/org/freedesktop/Hal/devices/platform_pcspkr' (string)
input.product = 'PC Speaker' (string)
linux.device_file = '/dev/input/event7' (string)
linux.hotplug_type = 2 (0x2) (int)
linux.subsystem = 'input' (string)
linux.sysfs_path = '/sys/devices/platform/pcspkr/input/input7/event7' (string)
udi = '/org/freedesktop/Hal/devices/platform_iTCO_wdt'
info.linux.driver = 'iTCO_wdt' (string)
info.parent = '/org/freedesktop/Hal/devices/computer' (string)
info.product = 'Platform Device (iTCO_wdt)' (string)
info.subsystem = 'platform' (string)
info.udi = '/org/freedesktop/Hal/devices/platform_iTCO_wdt' (string)
linux.hotplug_type = 2 (0x2) (int)
linux.subsystem = 'platform' (string)
linux.sysfs_path = '/sys/devices/platform/iTCO_wdt' (string)
platform.id = 'iTCO_wdt' (string)
udi = '/org/freedesktop/Hal/devices/platform_i8042'
info.linux.driver = 'i8042' (string)
info.parent = '/org/freedesktop/Hal/devices/computer' (string)
info.product = 'Platform Device (i8042)' (string)
info.subsystem = 'platform' (string)
info.udi = '/org/freedesktop/Hal/devices/platform_i8042' (string)
linux.hotplug_type = 2 (0x2) (int)
linux.subsystem = 'platform' (string)
linux.sysfs_path = '/sys/devices/platform/i8042' (string)
platform.id = 'i8042' (string)
udi = '/org/freedesktop/Hal/devices/platform_i8042_i8042_AUX_port'
info.linux.driver = 'psmouse' (string)
info.parent = '/org/freedesktop/Hal/devices/platform_i8042' (string)
info.product = 'i8042 AUX port' (string)
info.subsystem = 'serio' (string)
info.udi = '/org/freedesktop/Hal/devices/platform_i8042_i8042_AUX_port' (string)
linux.hotplug_type = 2 (0x2) (int)
linux.subsystem = 'serio' (string)
linux.sysfs_path = '/sys/devices/platform/i8042/serio1' (string)
serio.description = 'i8042 AUX port' (string)
serio.id = 'serio1' (string)
udi = '/org/freedesktop/Hal/devices/platform_i8042_i8042_AUX_port_logicaldev_input_0'
access_control.file = '/dev/input/event9' (string)
access_control.type = 'mouse' (string)
info.callouts.add = {'hal-acl-tool --add-device'} (string list)
info.callouts.remove = {'hal-acl-tool --remove-device'} (string list)
info.capabilities = {'input', 'input.mouse', 'input.touchpad', 'access_control'} (string list)
info.category = 'input' (string)
info.parent = '/org/freedesktop/Hal/devices/platform_i8042_i8042_AUX_port' (string)
info.product = 'AlpsPS/2 ALPS GlidePoint' (string)
info.subsystem = 'input' (string)
info.udi = '/org/freedesktop/Hal/devices/platform_i8042_i8042_AUX_port_logicaldev_input_0' (string)
input.device = '/dev/input/event9' (string)
input.originating_device = '/org/freedesktop/Hal/devices/platform_i8042_i8042_AUX_port' (string)
input.product = 'AlpsPS/2 ALPS GlidePoint' (string)
input.x11_driver = 'synaptics' (string)
linux.device_file = '/dev/input/event9' (string)
linux.hotplug_type = 2 (0x2) (int)
linux.subsystem = 'input' (string)
linux.sysfs_path = '/sys/devices/platform/i8042/serio1/input/input9/event9' (string)
udi = '/org/freedesktop/Hal/devices/platform_i8042_i8042_AUX_port_logicaldev_input'
access_control.file = '/dev/input/event8' (string)
access_control.type = 'mouse' (string)
info.callouts.add = {'hal-acl-tool --add-device'} (string list)
info.callouts.remove = {'hal-acl-tool --remove-device'} (string list)
info.capabilities = {'input', 'input.mouse', 'access_control'} (string list)
info.category = 'input' (string)
info.parent = '/org/freedesktop/Hal/devices/platform_i8042_i8042_AUX_port' (string)
info.product = 'PS/2 Mouse' (string)
info.subsystem = 'input' (string)
info.udi = '/org/freedesktop/Hal/devices/platform_i8042_i8042_AUX_port_logicaldev_input' (string)
input.device = '/dev/input/event8' (string)
input.originating_device = '/org/freedesktop/Hal/devices/platform_i8042_i8042_AUX_port' (string)
input.product = 'PS/2 Mouse' (string)
input.x11_driver = 'evdev' (string)
linux.device_file = '/dev/input/event8' (string)
linux.hotplug_type = 2 (0x2) (int)
linux.subsystem = 'input' (string)
linux.sysfs_path = '/sys/devices/platform/i8042/serio1/input/input8/event8' (string)
udi = '/org/freedesktop/Hal/devices/platform_i8042_i8042_KBD_port'
info.linux.driver = 'atkbd' (string)
info.parent = '/org/freedesktop/Hal/devices/platform_i8042' (string)
info.product = 'i8042 KBD port' (string)
info.subsystem = 'serio' (string)
info.udi = '/org/freedesktop/Hal/devices/platform_i8042_i8042_KBD_port' (string)
linux.hotplug_type = 2 (0x2) (int)
linux.subsystem = 'serio' (string)
linux.sysfs_path = '/sys/devices/platform/i8042/serio0' (string)
serio.description = 'i8042 KBD port' (string)
serio.id = 'serio0' (string)
udi = '/org/freedesktop/Hal/devices/platform_i8042_i8042_KBD_port_logicaldev_input'
info.addons.singleton = {'hald-addon-input'} (string list)
info.callouts.add = {'hal-setup-keymap', 'debian-setup-keyboard'} (string list)
info.capabilities = {'input', 'input.keyboard', 'input.keypad', 'input.keys', 'input.keymap', 'button'} (string list)
info.category = 'input' (string)
info.parent = '/org/freedesktop/Hal/devices/platform_i8042_i8042_KBD_port' (string)
info.product = 'AT Translated Set 2 keyboard' (string)
info.subsystem = 'input' (string)
info.udi = '/org/freedesktop/Hal/devices/platform_i8042_i8042_KBD_port_logicaldev_input' (string)
input.device = '/dev/input/event5' (string)
input.keymap.data = {'e001:playpause', 'e002:stopcd', 'e003:previoussong', 'e004:nextsong', 'e005:brightnessdown', 'e006:brightnessup', 'e007:battery', 'e008:wlan', 'e009:ejectclosecd', 'e00a:suspend', 'e00b:switchvideomode', 'e00f:switchvideomode', 'e010:previoussong', 'e011:prog1', 'e012:media', 'e013:f23', 'e015:camera', 'e00c:f23', 'e019:nextsong', 'e01b:switchvideomode', 'e022:playpause', 'e024:stopcd', 'e06d:media'} (string list)
input.originating_device = '/org/freedesktop/Hal/devices/platform_i8042_i8042_KBD_port' (string)
input.product = 'AT Translated Set 2 keyboard' (string)
input.x11_driver = 'evdev' (string)
input.xkb.layout = 'us' (string)
input.xkb.model = 'pc105' (string)
input.xkb.rules = 'evdev' (string)
linux.device_file = '/dev/input/event5' (string)
linux.hotplug_type = 2 (0x2) (int)
linux.subsystem = 'input' (string)
linux.sysfs_path = '/sys/devices/platform/i8042/serio0/input/input5/event5' (string)
udi = '/org/freedesktop/Hal/devices/platform_eisa_0'
info.parent = '/org/freedesktop/Hal/devices/computer' (string)
info.product = 'Platform Device (eisa.0)' (string)
info.subsystem = 'platform' (string)
info.udi = '/org/freedesktop/Hal/devices/platform_eisa_0' (string)
linux.hotplug_type = 2 (0x2) (int)
linux.subsystem = 'platform' (string)
linux.sysfs_path = '/sys/devices/platform/eisa.0' (string)
platform.id = 'eisa.0' (string)
udi = '/org/freedesktop/Hal/devices/platform_dcdbas'
info.linux.driver = 'dcdbas' (string)
info.parent = '/org/freedesktop/Hal/devices/computer' (string)
info.product = 'Platform Device (dcdbas)' (string)
info.subsystem = 'platform' (string)
info.udi = '/org/freedesktop/Hal/devices/platform_dcdbas' (string)
linux.hotplug_type = 2 (0x2) (int)
linux.subsystem = 'platform' (string)
linux.sysfs_path = '/sys/devices/platform/dcdbas' (string)
platform.id = 'dcdbas' (string)
udi = '/org/freedesktop/Hal/devices/dell_lcd_panel'
info.addons = {'hald-addon-dell-backlight'} (string list)
info.capabilities = {'laptop_panel'} (string list)
info.category = 'laptop_panel' (string)
info.interfaces = {'org.freedesktop.Hal.Device.LaptopPanel'} (string list)
info.parent = '/org/freedesktop/Hal/devices/platform_dcdbas' (string)
info.product = 'Dell Laptop Panel' (string)
info.subsystem = 'unknown' (string)
info.udi = '/org/freedesktop/Hal/devices/dell_lcd_panel' (string)
laptop_panel.access_method = 'custom' (string)
laptop_panel.brightness_in_hardware = true (bool)
laptop_panel.num_levels = 8 (0x8) (int)
udi = '/org/freedesktop/Hal/devices/dell_wwan_switch'
info.capabilities = {'killswitch'} (string list)
info.category = 'killswitch' (string)
info.interfaces = {'org.freedesktop.Hal.Device.KillSwitch'} (string list)
info.parent = '/org/freedesktop/Hal/devices/platform_dcdbas' (string)
info.product = 'Dell WWAN Switch' (string)
info.subsystem = 'unknown' (string)
info.udi = '/org/freedesktop/Hal/devices/dell_wwan_switch' (string)
killswitch.access_method = 'dell' (string)
killswitch.type = 'wwan' (string)
org.freedesktop.Hal.Device.KillSwitch.method_argnames = {'power', ''} (string list)
org.freedesktop.Hal.Device.KillSwitch.method_execpaths = {'hal-system-killswitch-set-power', 'hal-system-killswitch-get-power'} (string list)
org.freedesktop.Hal.Device.KillSwitch.method_names = {'SetPower', 'GetPower'} (string list)
org.freedesktop.Hal.Device.KillSwitch.method_signatures = {'b', ''} (string list)
udi = '/org/freedesktop/Hal/devices/dell_wlan_switch'
info.capabilities = {'killswitch'} (string list)
info.category = 'killswitch' (string)
info.interfaces = {'org.freedesktop.Hal.Device.KillSwitch'} (string list)
info.parent = '/org/freedesktop/Hal/devices/platform_dcdbas' (string)
info.product = 'Dell WLAN Switch' (string)
info.subsystem = 'unknown' (string)
info.udi = '/org/freedesktop/Hal/devices/dell_wlan_switch' (string)
killswitch.access_method = 'dell' (string)
killswitch.type = 'wlan' (string)
org.freedesktop.Hal.Device.KillSwitch.method_argnames = {'power', ''} (string list)
org.freedesktop.Hal.Device.KillSwitch.method_execpaths = {'hal-system-killswitch-set-power', 'hal-system-killswitch-get-power'} (string list)
org.freedesktop.Hal.Device.KillSwitch.method_names = {'SetPower', 'GetPower'} (string list)
org.freedesktop.Hal.Device.KillSwitch.method_signatures = {'b', ''} (string list)
udi = '/org/freedesktop/Hal/devices/dell_bluetooth_switch'
info.capabilities = {'killswitch'} (string list)
info.category = 'killswitch' (string)
info.interfaces = {'org.freedesktop.Hal.Device.KillSwitch'} (string list)
info.parent = '/org/freedesktop/Hal/devices/platform_dcdbas' (string)
info.product = 'Dell Bluetooth Switch' (string)
info.subsystem = 'unknown' (string)
info.udi = '/org/freedesktop/Hal/devices/dell_bluetooth_switch' (string)
killswitch.access_method = 'dell' (string)
killswitch.type = 'bluetooth' (string)
org.freedesktop.Hal.Device.KillSwitch.method_argnames = {'power', ''} (string list)
org.freedesktop.Hal.Device.KillSwitch.method_execpaths = {'hal-system-killswitch-set-power', 'hal-system-killswitch-get-power'} (string list)
org.freedesktop.Hal.Device.KillSwitch.method_names = {'SetPower', 'GetPower'} (string list)
org.freedesktop.Hal.Device.KillSwitch.method_signatures = {'b', ''} (string list)
udi = '/org/freedesktop/Hal/devices/platform_Fixed_MDIO_bus_0'
info.parent = '/org/freedesktop/Hal/devices/computer' (string)
info.product = 'Platform Device (Fixed MDIO bus.0)' (string)
info.subsystem = 'platform' (string)
info.udi = '/org/freedesktop/Hal/devices/platform_Fixed_MDIO_bus_0' (string)
linux.hotplug_type = 2 (0x2) (int)
linux.subsystem = 'platform' (string)
linux.sysfs_path = '/sys/devices/platform/Fixed MDIO bus.0' (string)
platform.id = 'Fixed MDIO bus.0' (string)
udi = '/org/freedesktop/Hal/devices/pci_8086_2930'
info.parent = '/org/freedesktop/Hal/devices/computer' (string)
info.product = '82801I (ICH9 Family) SMBus Controller' (string)
info.subsystem = 'pci' (string)
info.udi = '/org/freedesktop/Hal/devices/pci_8086_2930' (string)
info.vendor = 'Intel Corporation' (string)
linux.hotplug_type = 2 (0x2) (int)
linux.subsystem = 'pci' (string)
linux.sysfs_path = '/sys/devices/pci0000:00/0000:00:1f.3' (string)
pci.device_class = 12 (0xc) (int)
pci.device_protocol = 0 (0x0) (int)
pci.device_subclass = 5 (0x5) (int)
pci.linux.sysfs_path = '/sys/devices/pci0000:00/0000:00:1f.3' (string)
pci.product = '82801I (ICH9 Family) SMBus Controller' (string)
pci.product_id = 10544 (0x2930) (int)
pci.subsys_product_id = 700 (0x2bc) (int)
pci.subsys_vendor = 'Dell' (string)
pci.subsys_vendor_id = 4136 (0x1028) (int)
pci.vendor = 'Intel Corporation' (string)
pci.vendor_id = 32902 (0x8086) (int)
udi = '/org/freedesktop/Hal/devices/pci_8086_2929'
info.linux.driver = 'ahci' (string)
info.parent = '/org/freedesktop/Hal/devices/computer' (string)
info.product = 'ICH9M/M-E SATA AHCI Controller' (string)
info.subsystem = 'pci' (string)
info.udi = '/org/freedesktop/Hal/devices/pci_8086_2929' (string)
info.vendor = 'Intel Corporation' (string)
linux.hotplug_type = 2 (0x2) (int)
linux.subsystem = 'pci' (string)
linux.sysfs_path = '/sys/devices/pci0000:00/0000:00:1f.2' (string)
pci.device_class = 1 (0x1) (int)
pci.device_protocol = 1 (0x1) (int)
pci.device_subclass = 6 (0x6) (int)
pci.linux.sysfs_path = '/sys/devices/pci0000:00/0000:00:1f.2' (string)
pci.product = 'ICH9M/M-E SATA AHCI Controller' (string)
pci.product_id = 10537 (0x2929) (int)
pci.subsys_product_id = 700 (0x2bc) (int)
pci.subsys_vendor = 'Dell' (string)
pci.subsys_vendor_id = 4136 (0x1028) (int)
pci.vendor = 'Intel Corporation' (string)
pci.vendor_id = 32902 (0x8086) (int)
udi = '/org/freedesktop/Hal/devices/pci_8086_2929_scsi_host_2'
info.capabilities = {'scsi_host'} (string list)
info.category = 'scsi_host' (string)
info.parent = '/org/freedesktop/Hal/devices/pci_8086_2929' (string)
info.product = 'SCSI Host Adapter' (string)
info.subsystem = 'scsi_host' (string)
info.udi = '/org/freedesktop/Hal/devices/pci_8086_2929_scsi_host_2' (string)
linux.hotplug_type = 2 (0x2) (int)
linux.subsystem = 'scsi_host' (string)
linux.sysfs_path = '/sys/devices/pci0000:00/0000:00:1f.2/host3/scsi_host/host3' (string)
scsi_host.host = 3 (0x3) (int)
udi = '/org/freedesktop/Hal/devices/pci_8086_2929_scsi_host_1'
info.capabilities = {'scsi_host'} (string list)
info.category = 'scsi_host' (string)
info.parent = '/org/freedesktop/Hal/devices/pci_8086_2929' (string)
info.product = 'SCSI Host Adapter' (string)
info.subsystem = 'scsi_host' (string)
info.udi = '/org/freedesktop/Hal/devices/pci_8086_2929_scsi_host_1' (string)
linux.hotplug_type = 2 (0x2) (int)
linux.subsystem = 'scsi_host' (string)
linux.sysfs_path = '/sys/devices/pci0000:00/0000:00:1f.2/host2/scsi_host/host2' (string)
scsi_host.host = 2 (0x2) (int)
udi = '/org/freedesktop/Hal/devices/pci_8086_2929_scsi_host_0'
info.capabilities = {'scsi_host'} (string list)
info.category = 'scsi_host' (string)
info.parent = '/org/freedesktop/Hal/devices/pci_8086_2929' (string)
info.product = 'SCSI Host Adapter' (string)
info.subsystem = 'scsi_host' (string)
info.udi = '/org/freedesktop/Hal/devices/pci_8086_2929_scsi_host_0' (string)
linux.hotplug_type = 2 (0x2) (int)
linux.subsystem = 'scsi_host' (string)
linux.sysfs_path = '/sys/devices/pci0000:00/0000:00:1f.2/host1' (string)
scsi_host.host = 1 (0x1) (int)
udi = '/org/freedesktop/Hal/devices/pci_8086_2929_scsi_host_0_scsi_host'
info.capabilities = {'scsi_host'} (string list)
info.category = 'scsi_host' (string)
info.parent = '/org/freedesktop/Hal/devices/pci_8086_2929_scsi_host_0' (string)
info.product = 'SCSI Host Adapter' (string)
info.subsystem = 'scsi_host' (string)
info.udi = '/org/freedesktop/Hal/devices/pci_8086_2929_scsi_host_0_scsi_host' (string)
linux.hotplug_type = 2 (0x2) (int)
linux.subsystem = 'scsi_host' (string)
linux.sysfs_path = '/sys/devices/pci0000:00/0000:00:1f.2/host1/scsi_host/host1' (string)
scsi_host.host = 1 (0x1) (int)
udi = '/org/freedesktop/Hal/devices/pci_8086_2929_scsi_host_0_scsi_device_lun0'
info.linux.driver = 'sr' (string)
info.parent = '/org/freedesktop/Hal/devices/pci_8086_2929_scsi_host_0' (string)
info.product = 'SCSI Device' (string)
info.subsystem = 'scsi' (string)
info.udi = '/org/freedesktop/Hal/devices/pci_8086_2929_scsi_host_0_scsi_device_lun0' (string)
linux.hotplug_type = 2 (0x2) (int)
linux.subsystem = 'scsi' (string)
linux.sysfs_path = '/sys/devices/pci0000:00/0000:00:1f.2/host1/target1:0:0/1:0:0:0' (string)
scsi.bus = 0 (0x0) (int)
scsi.host = 1 (0x1) (int)
scsi.lun = 0 (0x0) (int)
scsi.model = 'DVD+-RW DS-8A3S' (string)
scsi.target = 0 (0x0) (int)
scsi.type = 'cdrom' (string)
scsi.vendor = 'PLDS' (string)
udi = '/org/freedesktop/Hal/devices/storage_model_DVD__RW_DS_8A3S'
access_control.file = '/dev/sr0' (string)
access_control.type = 'cdrom' (string)
block.device = '/dev/sr0' (string)
block.is_volume = false (bool)
block.major = 11 (0xb) (int)
block.minor = 0 (0x0) (int)
block.storage_device = '/org/freedesktop/Hal/devices/storage_model_DVD__RW_DS_8A3S' (string)
info.addons = {'hald-addon-storage'} (string list)
info.callouts.add = {'hal-acl-tool --add-device'} (string list)
info.callouts.remove = {'hal-acl-tool --remove-device'} (string list)
info.capabilities = {'storage', 'block', 'storage.cdrom', 'access_control'} (string list)
info.category = 'storage' (string)
info.interfaces = {'org.freedesktop.Hal.Device.Storage', 'org.freedesktop.Hal.Device.Storage', 'org.freedesktop.Hal.Device.Storage.Removable'} (string list)
info.parent = '/org/freedesktop/Hal/devices/pci_8086_2929_scsi_host_0_scsi_device_lun0' (string)
info.product = 'DVD+-RW DS-8A3S' (string)
info.udi = '/org/freedesktop/Hal/devices/storage_model_DVD__RW_DS_8A3S' (string)
info.vendor = 'PLDS' (string)
linux.hotplug_type = 3 (0x3) (int)
linux.sysfs_path = '/sys/devices/pci0000:00/0000:00:1f.2/host1/target1:0:0/1:0:0:0/block/sr0' (string)
org.freedesktop.Hal.Device.Storage.method_argnames = {'extra_options', 'extra_options'} (string list)
org.freedesktop.Hal.Device.Storage.method_execpaths = {'hal-storage-eject', 'hal-storage-closetray'} (string list)
org.freedesktop.Hal.Device.Storage.method_names = {'Eject', 'CloseTray'} (string list)
org.freedesktop.Hal.Device.Storage.method_signatures = {'as', 'as'} (string list)
storage.automount_enabled_hint = true (bool)
storage.bus = 'pci' (string)
storage.cdrom.bd = false (bool)
storage.cdrom.bdr = false (bool)
storage.cdrom.bdre = false (bool)
storage.cdrom.cdr = true (bool)
storage.cdrom.cdrw = true (bool)
storage.cdrom.dvd = true (bool)
storage.cdrom.dvdplusr = true (bool)
storage.cdrom.dvdplusrdl = true (bool)
storage.cdrom.dvdplusrw = true (bool)
storage.cdrom.dvdplusrwdl = false (bool)
storage.cdrom.dvdr = true (bool)
storage.cdrom.dvdram = true (bool)
storage.cdrom.dvdrdl = true (bool)
storage.cdrom.dvdrw = true (bool)
storage.cdrom.hddvd = false (bool)
storage.cdrom.hddvdr = false (bool)
storage.cdrom.hddvdrw = false (bool)
storage.cdrom.mo = false (bool)
storage.cdrom.mrw = true (bool)
storage.cdrom.mrw_w = true (bool)
storage.cdrom.read_speed = 11080 (0x2b48) (int)
storage.cdrom.support_media_changed = true (bool)
storage.cdrom.support_multisession = true (bool)
storage.cdrom.write_speed = 5540 (0x15a4) (int)
storage.cdrom.write_speeds = {'5540', '4155'} (string list)
storage.drive_type = 'cdrom' (string)
storage.firmware_version = 'HD13' (string)
storage.hotpluggable = false (bool)
storage.lun = 0 (0x0) (int)
storage.media_check_enabled = true (bool)
storage.model = 'DVD+-RW DS-8A3S' (string)
storage.no_partitions_hint = true (bool)
storage.originating_device = '/org/freedesktop/Hal/devices/computer' (string)
storage.removable = true (bool)
storage.removable.media_available = true (bool)
storage.removable.media_size = 732909568 (0x2baf5000) (uint64)
storage.removable.support_async_notification = false (bool)
storage.requires_eject = true (bool)
storage.size = 0 (0x0) (uint64)
storage.vendor = 'PLDS' (string)
udi = '/org/freedesktop/Hal/devices/volume_label_Ubuntu_9_04_i386'
block.device = '/dev/sr0' (string)
block.is_volume = true (bool)
block.major = 11 (0xb) (int)
block.minor = 0 (0x0) (int)
block.storage_device = '/org/freedesktop/Hal/devices/storage_model_DVD__RW_DS_8A3S' (string)
info.capabilities = {'volume.disc', 'volume', 'block'} (string list)
info.category = 'volume' (string)
info.interfaces = {'org.freedesktop.Hal.Device.Volume'} (string list)
info.parent = '/org/freedesktop/Hal/devices/storage_model_DVD__RW_DS_8A3S' (string)
info.product = 'Ubuntu 9.04 i386' (string)
info.udi = '/org/freedesktop/Hal/devices/volume_label_Ubuntu_9_04_i386' (string)
linux.hotplug_type = 3 (0x3) (int)
linux.sysfs_path = '/sys/devices/pci0000:00/0000:00:1f.2/host1/target1:0:0/1:0:0:0/block/sr0/fakevolume' (string)
org.freedesktop.Hal.Device.Volume.method_argnames = {'mount_point fstype extra_options', 'extra_options', 'extra_options'} (string list)
org.freedesktop.Hal.Device.Volume.method_execpaths = {'hal-storage-mount', 'hal-storage-unmount', 'hal-storage-eject'} (string list)
org.freedesktop.Hal.Device.Volume.method_names = {'Mount', 'Unmount', 'Eject'} (string list)
org.freedesktop.Hal.Device.Volume.method_signatures = {'ssas', 'as', 'as'} (string list)
volume.block_size = 2048 (0x800) (int)
volume.disc.capacity = 4706074624 (0x118810000) (uint64)
volume.disc.has_audio = false (bool)
volume.disc.has_data = true (bool)
volume.disc.is_appendable = false (bool)
volume.disc.is_blank = false (bool)
volume.disc.is_blurayvideo = false (bool)
volume.disc.is_rewritable = true (bool)
volume.disc.is_svcd = false (bool)
volume.disc.is_vcd = false (bool)
volume.disc.is_videodvd = false (bool)
volume.disc.type = 'dvd_rw' (string)
volume.fstype = 'iso9660' (string)
volume.fsusage = 'filesystem' (string)
volume.fsversion = '' (string)
volume.ignore = false (bool)
volume.is_disc = true (bool)
volume.is_mounted = true (bool)
volume.is_mounted_read_only = true (bool)
volume.is_partition = false (bool)
volume.label = 'Ubuntu 9.04 i386' (string)
volume.linux.is_device_mapper = false (bool)
volume.mount.valid_options = {'ro', 'sync', 'dirsync', 'noatime', 'nodiratime', 'noexec', 'quiet', 'remount', 'exec', 'utf8', 'uid=', 'mode=', 'iocharset='} (string list)
volume.mount_point = '/cdrom' (string)
volume.num_blocks = 1431464 (0x15d7a8) (uint64)
volume.size = 732909568 (0x2baf5000) (uint64)
volume.unmount.valid_options = {'lazy'} (string list)
volume.uuid = '' (string)
udi = '/org/freedesktop/Hal/devices/pci_8086_2929_scsi_host_0_scsi_device_lun0_scsi_generic'
access_control.file = '/dev/sg1' (string)
access_control.type = 'cdrom' (string)
info.callouts.add = {'hal-acl-tool --add-device'} (string list)
info.callouts.remove = {'hal-acl-tool --remove-device'} (string list)
info.capabilities = {'scsi_generic', 'access_control'} (string list)
info.category = 'scsi_generic' (string)
info.parent = '/org/freedesktop/Hal/devices/pci_8086_2929_scsi_host_0_scsi_device_lun0' (string)
info.product = 'SCSI Generic Interface' (string)
info.subsystem = 'scsi_generic' (string)
info.udi = '/org/freedesktop/Hal/devices/pci_8086_2929_scsi_host_0_scsi_device_lun0_scsi_generic' (string)
linux.device_file = '/dev/sg1' (string)
linux.hotplug_type = 2 (0x2) (int)
linux.subsystem = 'scsi_generic' (string)
linux.sysfs_path = '/sys/devices/pci0000:00/0000:00:1f.2/host1/target1:0:0/1:0:0:0/scsi_generic/sg1' (string)
scsi_generic.device = '/dev/sg1' (string)
udi = '/org/freedesktop/Hal/devices/pci_8086_2929_scsi_host'
info.capabilities = {'scsi_host'} (string list)
info.category = 'scsi_host' (string)
info.parent = '/org/freedesktop/Hal/devices/pci_8086_2929' (string)
info.product = 'SCSI Host Adapter' (string)
info.subsystem = 'scsi_host' (string)
info.udi = '/org/freedesktop/Hal/devices/pci_8086_2929_scsi_host' (string)
linux.hotplug_type = 2 (0x2) (int)
linux.subsystem = 'scsi_host' (string)
linux.sysfs_path = '/sys/devices/pci0000:00/0000:00:1f.2/host0' (string)
scsi_host.host = 0 (0x0) (int)
udi = '/org/freedesktop/Hal/devices/pci_8086_2929_scsi_host_scsi_host'
info.capabilities = {'scsi_host'} (string list)
info.category = 'scsi_host' (string)
info.parent = '/org/freedesktop/Hal/devices/pci_8086_2929_scsi_host' (string)
info.product = 'SCSI Host Adapter' (string)
info.subsystem = 'scsi_host' (string)
info.udi = '/org/freedesktop/Hal/devices/pci_8086_2929_scsi_host_scsi_host' (string)
linux.hotplug_type = 2 (0x2) (int)
linux.subsystem = 'scsi_host' (string)
linux.sysfs_path = '/sys/devices/pci0000:00/0000:00:1f.2/host0/scsi_host/host0' (string)
scsi_host.host = 0 (0x0) (int)
udi = '/org/freedesktop/Hal/devices/pci_8086_2929_scsi_host_scsi_device_lun0'
info.linux.driver = 'sd' (string)
info.parent = '/org/freedesktop/Hal/devices/pci_8086_2929_scsi_host' (string)
info.product = 'SCSI Device' (string)
info.subsystem = 'scsi' (string)
info.udi = '/org/freedesktop/Hal/devices/pci_8086_2929_scsi_host_scsi_device_lun0' (string)
linux.hotplug_type = 2 (0x2) (int)
linux.subsystem = 'scsi' (string)
linux.sysfs_path = '/sys/devices/pci0000:00/0000:00:1f.2/host0/target0:0:0/0:0:0:0' (string)
scsi.bus = 0 (0x0) (int)
scsi.host = 0 (0x0) (int)
scsi.lun = 0 (0x0) (int)
scsi.model = 'WDC WD1600BEVT-7' (string)
scsi.target = 0 (0x0) (int)
scsi.type = 'disk' (string)
scsi.vendor = 'ATA' (string)
udi = '/org/freedesktop/Hal/devices/storage_serial_SATA_WDC_WD1600BEVT__WD_WX20E59Y7313'
block.device = '/dev/sda' (string)
block.is_volume = false (bool)
block.major = 8 (0x8) (int)
block.minor = 0 (0x0) (int)
block.storage_device = '/org/freedesktop/Hal/devices/storage_serial_SATA_WDC_WD1600BEVT__WD_WX20E59Y7313' (string)
info.capabilities = {'storage', 'block'} (string list)
info.category = 'storage' (string)
info.parent = '/org/freedesktop/Hal/devices/pci_8086_2929_scsi_host_scsi_device_lun0' (string)
info.product = 'WDC WD1600BEVT-7' (string)
info.udi = '/org/freedesktop/Hal/devices/storage_serial_SATA_WDC_WD1600BEVT__WD_WX20E59Y7313' (string)
info.vendor = 'ATA' (string)
linux.hotplug_type = 3 (0x3) (int)
linux.sysfs_path = '/sys/devices/pci0000:00/0000:00:1f.2/host0/target0:0:0/0:0:0:0/block/sda' (string)
storage.automount_enabled_hint = false (bool)
storage.bus = 'pci' (string)
storage.drive_type = 'disk' (string)
storage.firmware_version = '11.0' (string)
storage.hotpluggable = false (bool)
storage.lun = 0 (0x0) (int)
storage.media_check_enabled = false (bool)
storage.model = 'WDC WD1600BEVT-7' (string)
storage.no_partitions_hint = false (bool)
storage.originating_device = '/org/freedesktop/Hal/devices/computer' (string)
storage.partitioning_scheme = 'mbr' (string)
storage.removable = false (bool)
storage.removable.media_available = true (bool)
storage.removable.media_size = 160041885696 (0x25433d6000) (uint64)
storage.requires_eject = false (bool)
storage.serial = 'SATA_WDC_WD1600BEVT-_WD-WX20E59Y7313' (string)
storage.size = 160041885696 (0x25433d6000) (uint64)
storage.vendor = 'ATA' (string)
udi = '/org/freedesktop/Hal/devices/volume_uuid_b25673dd_6844_4fc6_8c4d_90f5d52e0b9d'
block.device = '/dev/sda3' (string)
block.is_volume = true (bool)
block.major = 8 (0x8) (int)
block.minor = 3 (0x3) (int)
block.storage_device = '/org/freedesktop/Hal/devices/storage_serial_SATA_WDC_WD1600BEVT__WD_WX20E59Y7313' (string)
info.capabilities = {'volume', 'block'} (string list)
info.category = 'volume' (string)
info.interfaces = {'org.freedesktop.Hal.Device.Volume'} (string list)
info.parent = '/org/freedesktop/Hal/devices/storage_serial_SATA_WDC_WD1600BEVT__WD_WX20E59Y7313' (string)
info.product = 'Volume (ext3)' (string)
info.udi = '/org/freedesktop/Hal/devices/volume_uuid_b25673dd_6844_4fc6_8c4d_90f5d52e0b9d' (string)
linux.hotplug_type = 3 (0x3) (int)
linux.sysfs_path = '/sys/devices/pci0000:00/0000:00:1f.2/host0/target0:0:0/0:0:0:0/block/sda/sda3' (string)
org.freedesktop.Hal.Device.Volume.method_argnames = {'mount_point fstype extra_options', 'extra_options', 'extra_options'} (string list)
org.freedesktop.Hal.Device.Volume.method_execpaths = {'hal-storage-mount', 'hal-storage-unmount', 'hal-storage-eject'} (string list)
org.freedesktop.Hal.Device.Volume.method_names = {'Mount', 'Unmount', 'Eject'} (string list)
org.freedesktop.Hal.Device.Volume.method_signatures = {'ssas', 'as', 'as'} (string list)
volume.block_size = 512 (0x200) (int)
volume.fstype = 'ext3' (string)
volume.fsusage = 'filesystem' (string)
volume.fsversion = '1.0' (string)
volume.ignore = false (bool)
volume.is_disc = false (bool)
volume.is_mounted = true (bool)
volume.is_mounted_read_only = false (bool)
volume.is_partition = true (bool)
volume.label = '' (string)
volume.linux.is_device_mapper = false (bool)
volume.mount.valid_options = {'ro', 'sync', 'dirsync', 'noatime', 'nodiratime', 'noexec', 'quiet', 'remount', 'exec', 'acl', 'user_xattr', 'data='} (string list)
volume.mount_point = '/mnt' (string)
volume.num_blocks = 304688790 (0x12292e96) (uint64)
volume.partition.media_size = 160041885696 (0x25433d6000) (uint64)
volume.partition.number = 3 (0x3) (int)
volume.partition.start = 4038612480 (0xf0b85600) (uint64)
volume.size = 156000660480 (0x24525d2c00) (uint64)
volume.unmount.valid_options = {'lazy'} (string list)
volume.uuid = 'b25673dd-6844-4fc6-8c4d-90f5d52e0b9d' (string)
udi = '/org/freedesktop/Hal/devices/volume_part2_size_3997486080'
block.device = '/dev/sda2' (string)
block.is_volume = true (bool)
block.major = 8 (0x8) (int)
block.minor = 2 (0x2) (int)
block.storage_device = '/org/freedesktop/Hal/devices/storage_serial_SATA_WDC_WD1600BEVT__WD_WX20E59Y7313' (string)
info.capabilities = {'volume', 'block'} (string list)
info.category = 'volume' (string)
info.parent = '/org/freedesktop/Hal/devices/storage_serial_SATA_WDC_WD1600BEVT__WD_WX20E59Y7313' (string)
info.product = 'Volume (swap)' (string)
info.udi = '/org/freedesktop/Hal/devices/volume_part2_size_3997486080' (string)
linux.hotplug_type = 3 (0x3) (int)
linux.sysfs_path = '/sys/devices/pci0000:00/0000:00:1f.2/host0/target0:0:0/0:0:0:0/block/sda/sda2' (string)
volume.block_size = 512 (0x200) (int)
volume.fstype = 'swap' (string)
volume.fsusage = 'other' (string)
volume.fsversion = '2' (string)
volume.is_disc = false (bool)
volume.is_mounted = false (bool)
volume.is_mounted_read_only = false (bool)
volume.is_partition = true (bool)
volume.label = '' (string)
volume.linux.is_device_mapper = false (bool)
volume.mount_point = '' (string)
volume.num_blocks = 7807590 (0x772266) (uint64)
volume.partition.media_size = 160041885696 (0x25433d6000) (uint64)
volume.partition.number = 2 (0x2) (int)
volume.partition.start = 41126400 (0x2738a00) (uint64)
volume.size = 3997486080 (0xee44cc00) (uint64)
volume.uuid = '' (string)
udi = '/org/freedesktop/Hal/devices/volume_uuid_3030_3030'
block.device = '/dev/sda1' (string)
block.is_volume = true (bool)
block.major = 8 (0x8) (int)
block.minor = 1 (0x1) (int)
block.storage_device = '/org/freedesktop/Hal/devices/storage_serial_SATA_WDC_WD1600BEVT__WD_WX20E59Y7313' (string)
info.capabilities = {'volume', 'block'} (string list)
info.category = 'volume' (string)
info.interfaces = {'org.freedesktop.Hal.Device.Volume'} (string list)
info.parent = '/org/freedesktop/Hal/devices/storage_serial_SATA_WDC_WD1600BEVT__WD_WX20E59Y7313' (string)
info.product = 'DellUtility' (string)
info.udi = '/org/freedesktop/Hal/devices/volume_uuid_3030_3030' (string)
linux.hotplug_type = 3 (0x3) (int)
linux.sysfs_path = '/sys/devices/pci0000:00/0000:00:1f.2/host0/target0:0:0/0:0:0:0/block/sda/sda1' (string)
org.freedesktop.Hal.Device.Volume.method_argnames = {'mount_point fstype extra_options', 'extra_options', 'extra_options'} (string list)
org.freedesktop.Hal.Device.Volume.method_execpaths = {'hal-storage-mount', 'hal-storage-unmount', 'hal-storage-eject'} (string list)
org.freedesktop.Hal.Device.Volume.method_names = {'Mount', 'Unmount', 'Eject'} (string list)
org.freedesktop.Hal.Device.Volume.method_signatures = {'ssas', 'as', 'as'} (string list)
volume.block_size = 512 (0x200) (int)
volume.fstype = 'vfat' (string)
volume.fsusage = 'filesystem' (string)
volume.fsversion = 'FAT16' (string)
volume.ignore = true (bool)
volume.is_disc = false (bool)
volume.is_mounted = false (bool)
volume.is_mounted_read_only = false (bool)
volume.is_partition = true (bool)
volume.label = 'DellUtility' (string)
volume.linux.is_device_mapper = false (bool)
volume.mount.valid_options = {'ro', 'sync', 'dirsync', 'noatime', 'nodiratime', 'noexec', 'quiet', 'remount', 'exec', 'utf8', 'shortname=', 'codepage=', 'iocharset=', 'umask=', 'dmask=', 'fmask=', 'uid=', 'flush'} (string list)
volume.mount_point = '' (string)
volume.num_blocks = 80262 (0x13986) (uint64)
volume.partition.media_size = 160041885696 (0x25433d6000) (uint64)
volume.partition.number = 1 (0x1) (int)
volume.partition.start = 32256 (0x7e00) (uint64)
volume.size = 41094144 (0x2730c00) (uint64)
volume.unmount.valid_options = {'lazy'} (string list)
volume.uuid = '3030-3030' (string)
udi = '/org/freedesktop/Hal/devices/pci_8086_2929_scsi_host_scsi_device_lun0_scsi_generic'
info.capabilities = {'scsi_generic'} (string list)
info.category = 'scsi_generic' (string)
info.parent = '/org/freedesktop/Hal/devices/pci_8086_2929_scsi_host_scsi_device_lun0' (string)
info.product = 'SCSI Generic Interface' (string)
info.subsystem = 'scsi_generic' (string)
info.udi = '/org/freedesktop/Hal/devices/pci_8086_2929_scsi_host_scsi_device_lun0_scsi_generic' (string)
linux.device_file = '/dev/sg0' (string)
linux.hotplug_type = 2 (0x2) (int)
linux.subsystem = 'scsi_generic' (string)
linux.sysfs_path = '/sys/devices/pci0000:00/0000:00:1f.2/host0/target0:0:0/0:0:0:0/scsi_generic/sg0' (string)
scsi_generic.device = '/dev/sg0' (string)
udi = '/org/freedesktop/Hal/devices/pci_8086_2919'
info.parent = '/org/freedesktop/Hal/devices/computer' (string)
info.product = 'ICH9M LPC Interface Controller' (string)
info.subsystem = 'pci' (string)
info.udi = '/org/freedesktop/Hal/devices/pci_8086_2919' (string)
info.vendor = 'Intel Corporation' (string)
linux.hotplug_type = 2 (0x2) (int)
linux.subsystem = 'pci' (string)
linux.sysfs_path = '/sys/devices/pci0000:00/0000:00:1f.0' (string)
pci.device_class = 6 (0x6) (int)
pci.device_protocol = 0 (0x0) (int)
pci.device_subclass = 1 (0x1) (int)
pci.linux.sysfs_path = '/sys/devices/pci0000:00/0000:00:1f.0' (string)
pci.product = 'ICH9M LPC Interface Controller' (string)
pci.product_id = 10521 (0x2919) (int)
pci.subsys_product_id = 700 (0x2bc) (int)
pci.subsys_vendor = 'Dell' (string)
pci.subsys_vendor_id = 4136 (0x1028) (int)
pci.vendor = 'Intel Corporation' (string)
pci.vendor_id = 32902 (0x8086) (int)
udi = '/org/freedesktop/Hal/devices/pci_8086_2448'
info.parent = '/org/freedesktop/Hal/devices/computer' (string)
info.product = '82801 Mobile PCI Bridge' (string)
info.subsystem = 'pci' (string)
info.udi = '/org/freedesktop/Hal/devices/pci_8086_2448' (string)
info.vendor = 'Intel Corporation' (string)
linux.hotplug_type = 2 (0x2) (int)
linux.subsystem = 'pci' (string)
linux.sysfs_path = '/sys/devices/pci0000:00/0000:00:1e.0' (string)
pci.device_class = 6 (0x6) (int)
pci.device_protocol = 1 (0x1) (int)
pci.device_subclass = 4 (0x4) (int)
pci.linux.sysfs_path = '/sys/devices/pci0000:00/0000:00:1e.0' (string)
pci.product = '82801 Mobile PCI Bridge' (string)
pci.product_id = 9288 (0x2448) (int)
pci.subsys_product_id = 0 (0x0) (int)
pci.subsys_vendor_id = 0 (0x0) (int)
pci.vendor = 'Intel Corporation' (string)
pci.vendor_id = 32902 (0x8086) (int)
udi = '/org/freedesktop/Hal/devices/pci_8086_293a'
info.linux.driver = 'ehci_hcd' (string)
info.parent = '/org/freedesktop/Hal/devices/computer' (string)
info.product = '82801I (ICH9 Family) USB2 EHCI Controller #1' (string)
info.subsystem = 'pci' (string)
info.udi = '/org/freedesktop/Hal/devices/pci_8086_293a' (string)
info.vendor = 'Intel Corporation' (string)
linux.hotplug_type = 2 (0x2) (int)
linux.subsystem = 'pci' (string)
linux.sysfs_path = '/sys/devices/pci0000:00/0000:00:1d.7' (string)
pci.device_class = 12 (0xc) (int)
pci.device_protocol = 32 (0x20) (int)
pci.device_subclass = 3 (0x3) (int)
pci.linux.sysfs_path = '/sys/devices/pci0000:00/0000:00:1d.7' (string)
pci.product = '82801I (ICH9 Family) USB2 EHCI Controller #1' (string)
pci.product_id = 10554 (0x293a) (int)
pci.subsys_product_id = 700 (0x2bc) (int)
pci.subsys_vendor = 'Dell' (string)
pci.subsys_vendor_id = 4136 (0x1028) (int)
pci.vendor = 'Intel Corporation' (string)
pci.vendor_id = 32902 (0x8086) (int)
udi = '/org/freedesktop/Hal/devices/usb_device_1d6b_2_0000_00_1d_7'
info.linux.driver = 'usb' (string)
info.parent = '/org/freedesktop/Hal/devices/pci_8086_293a' (string)
info.product = '2.0 root hub' (string)
info.subsystem = 'usb_device' (string)
info.udi = '/org/freedesktop/Hal/devices/usb_device_1d6b_2_0000_00_1d_7' (string)
info.vendor = 'Linux Foundation' (string)
linux.device_file = '/dev/bus/usb/002/001' (string)
linux.hotplug_type = 2 (0x2) (int)
linux.subsystem = 'usb' (string)
linux.sysfs_path = '/sys/devices/pci0000:00/0000:00:1d.7/usb2' (string)
usb_device.bus_number = 2 (0x2) (int)
usb_device.can_wake_up = true (bool)
usb_device.configuration_value = 1 (0x1) (int)
usb_device.device_class = 9 (0x9) (int)
usb_device.device_protocol = 0 (0x0) (int)
usb_device.device_revision_bcd = 518 (0x206) (int)
usb_device.device_subclass = 0 (0x0) (int)
usb_device.is_self_powered = true (bool)
usb_device.linux.device_number = 1 (0x1) (int)
usb_device.linux.sysfs_path = '/sys/devices/pci0000:00/0000:00:1d.7/usb2' (string)
usb_device.max_power = 0 (0x0) (int)
usb_device.num_configurations = 1 (0x1) (int)
usb_device.num_interfaces = 1 (0x1) (int)
usb_device.num_ports = 6 (0x6) (int)
usb_device.product = '2.0 root hub' (string)
usb_device.product_id = 2 (0x2) (int)
usb_device.serial = '0000:00:1d.7' (string)
usb_device.speed = 480.0 (480) (double)
usb_device.vendor = 'Linux Foundation' (string)
usb_device.vendor_id = 7531 (0x1d6b) (int)
usb_device.version = 2.0 (2) (double)
udi = '/org/freedesktop/Hal/devices/usb_device_1d6b_2_0000_00_1d_7_if0'
info.linux.driver = 'hub' (string)
info.parent = '/org/freedesktop/Hal/devices/usb_device_1d6b_2_0000_00_1d_7' (string)
info.product = 'USB Hub Interface' (string)
info.subsystem = 'usb' (string)
info.udi = '/org/freedesktop/Hal/devices/usb_device_1d6b_2_0000_00_1d_7_if0' (string)
linux.hotplug_type = 2 (0x2) (int)
linux.subsystem = 'usb' (string)
linux.sysfs_path = '/sys/devices/pci0000:00/0000:00:1d.7/usb2/2-0:1.0' (string)
usb.bus_number = 2 (0x2) (int)
usb.can_wake_up = true (bool)
usb.configuration_value = 1 (0x1) (int)
usb.device_class = 9 (0x9) (int)
usb.device_protocol = 0 (0x0) (int)
usb.device_revision_bcd = 518 (0x206) (int)
usb.device_subclass = 0 (0x0) (int)
usb.interface.class = 9 (0x9) (int)
usb.interface.number = 0 (0x0) (int)
usb.interface.protocol = 0 (0x0) (int)
usb.interface.subclass = 0 (0x0) (int)
usb.is_self_powered = true (bool)
usb.linux.device_number = 1 (0x1) (int)
usb.linux.sysfs_path = '/sys/devices/pci0000:00/0000:00:1d.7/usb2/2-0:1.0' (string)
usb.max_power = 0 (0x0) (int)
usb.num_configurations = 1 (0x1) (int)
usb.num_interfaces = 1 (0x1) (int)
usb.num_ports = 6 (0x6) (int)
usb.product = 'USB Hub Interface' (string)
usb.product_id = 2 (0x2) (int)
usb.serial = '0000:00:1d.7' (string)
usb.speed = 480.0 (480) (double)
usb.vendor = 'Linux Foundation' (string)
usb.vendor_id = 7531 (0x1d6b) (int)
usb.version = 2.0 (2) (double)
udi = '/org/freedesktop/Hal/devices/pci_8086_2936'
info.linux.driver = 'uhci_hcd' (string)
info.parent = '/org/freedesktop/Hal/devices/computer' (string)
info.product = '82801I (ICH9 Family) USB UHCI Controller #3' (string)
info.subsystem = 'pci' (string)
info.udi = '/org/freedesktop/Hal/devices/pci_8086_2936' (string)
info.vendor = 'Intel Corporation' (string)
linux.hotplug_type = 2 (0x2) (int)
linux.subsystem = 'pci' (string)
linux.sysfs_path = '/sys/devices/pci0000:00/0000:00:1d.2' (string)
pci.device_class = 12 (0xc) (int)
pci.device_protocol = 0 (0x0) (int)
pci.device_subclass = 3 (0x3) (int)
pci.linux.sysfs_path = '/sys/devices/pci0000:00/0000:00:1d.2' (string)
pci.product = '82801I (ICH9 Family) USB UHCI Controller #3' (string)
pci.product_id = 10550 (0x2936) (int)
pci.subsys_product_id = 700 (0x2bc) (int)
pci.subsys_vendor = 'Dell' (string)
pci.subsys_vendor_id = 4136 (0x1028) (int)
pci.vendor = 'Intel Corporation' (string)
pci.vendor_id = 32902 (0x8086) (int)
udi = '/org/freedesktop/Hal/devices/usb_device_1d6b_1_0000_00_1d_2'
info.linux.driver = 'usb' (string)
info.parent = '/org/freedesktop/Hal/devices/pci_8086_2936' (string)
info.product = '1.1 root hub' (string)
info.subsystem = 'usb_device' (string)
info.udi = '/org/freedesktop/Hal/devices/usb_device_1d6b_1_0000_00_1d_2' (string)
info.vendor = 'Linux Foundation' (string)
linux.device_file = '/dev/bus/usb/008/001' (string)
linux.hotplug_type = 2 (0x2) (int)
linux.subsystem = 'usb' (string)
linux.sysfs_path = '/sys/devices/pci0000:00/0000:00:1d.2/usb8' (string)
usb_device.bus_number = 8 (0x8) (int)
usb_device.can_wake_up = true (bool)
usb_device.configuration_value = 1 (0x1) (int)
usb_device.device_class = 9 (0x9) (int)
usb_device.device_protocol = 0 (0x0) (int)
usb_device.device_revision_bcd = 518 (0x206) (int)
usb_device.device_subclass = 0 (0x0) (int)
usb_device.is_self_powered = true (bool)
usb_device.linux.device_number = 1 (0x1) (int)
usb_device.linux.sysfs_path = '/sys/devices/pci0000:00/0000:00:1d.2/usb8' (string)
usb_device.max_power = 0 (0x0) (int)
usb_device.num_configurations = 1 (0x1) (int)
usb_device.num_interfaces = 1 (0x1) (int)
usb_device.num_ports = 2 (0x2) (int)
usb_device.product = '1.1 root hub' (string)
usb_device.product_id = 1 (0x1) (int)
usb_device.serial = '0000:00:1d.2' (string)
usb_device.speed = 12.0 (12) (double)
usb_device.vendor = 'Linux Foundation' (string)
usb_device.vendor_id = 7531 (0x1d6b) (int)
usb_device.version = 1.1 (1.1) (double)
udi = '/org/freedesktop/Hal/devices/usb_device_1d6b_1_0000_00_1d_2_if0'
info.linux.driver = 'hub' (string)
info.parent = '/org/freedesktop/Hal/devices/usb_device_1d6b_1_0000_00_1d_2' (string)
info.product = 'USB Hub Interface' (string)
info.subsystem = 'usb' (string)
info.udi = '/org/freedesktop/Hal/devices/usb_device_1d6b_1_0000_00_1d_2_if0' (string)
linux.hotplug_type = 2 (0x2) (int)
linux.subsystem = 'usb' (string)
linux.sysfs_path = '/sys/devices/pci0000:00/0000:00:1d.2/usb8/8-0:1.0' (string)
usb.bus_number = 8 (0x8) (int)
usb.can_wake_up = true (bool)
usb.configuration_value = 1 (0x1) (int)
usb.device_class = 9 (0x9) (int)
usb.device_protocol = 0 (0x0) (int)
usb.device_revision_bcd = 518 (0x206) (int)
usb.device_subclass = 0 (0x0) (int)
usb.interface.class = 9 (0x9) (int)
usb.interface.number = 0 (0x0) (int)
usb.interface.protocol = 0 (0x0) (int)
usb.interface.subclass = 0 (0x0) (int)
usb.is_self_powered = true (bool)
usb.linux.device_number = 1 (0x1) (int)
usb.linux.sysfs_path = '/sys/devices/pci0000:00/0000:00:1d.2/usb8/8-0:1.0' (string)
usb.max_power = 0 (0x0) (int)
usb.num_configurations = 1 (0x1) (int)
usb.num_interfaces = 1 (0x1) (int)
usb.num_ports = 2 (0x2) (int)
usb.product = 'USB Hub Interface' (string)
usb.product_id = 1 (0x1) (int)
usb.serial = '0000:00:1d.2' (string)
usb.speed = 12.0 (12) (double)
usb.vendor = 'Linux Foundation' (string)
usb.vendor_id = 7531 (0x1d6b) (int)
usb.version = 1.1 (1.1) (double)
udi = '/org/freedesktop/Hal/devices/pci_8086_2935'
info.linux.driver = 'uhci_hcd' (string)
info.parent = '/org/freedesktop/Hal/devices/computer' (string)
info.product = '82801I (ICH9 Family) USB UHCI Controller #2' (string)
info.subsystem = 'pci' (string)
info.udi = '/org/freedesktop/Hal/devices/pci_8086_2935' (string)
info.vendor = 'Intel Corporation' (string)
linux.hotplug_type = 2 (0x2) (int)
linux.subsystem = 'pci' (string)
linux.sysfs_path = '/sys/devices/pci0000:00/0000:00:1d.1' (string)
pci.device_class = 12 (0xc) (int)
pci.device_protocol = 0 (0x0) (int)
pci.device_subclass = 3 (0x3) (int)
pci.linux.sysfs_path = '/sys/devices/pci0000:00/0000:00:1d.1' (string)
pci.product = '82801I (ICH9 Family) USB UHCI Controller #2' (string)
pci.product_id = 10549 (0x2935) (int)
pci.subsys_product_id = 700 (0x2bc) (int)
pci.subsys_vendor = 'Dell' (string)
pci.subsys_vendor_id = 4136 (0x1028) (int)
pci.vendor = 'Intel Corporation' (string)
pci.vendor_id = 32902 (0x8086) (int)
udi = '/org/freedesktop/Hal/devices/usb_device_1d6b_1_0000_00_1d_1'
info.linux.driver = 'usb' (string)
info.parent = '/org/freedesktop/Hal/devices/pci_8086_2935' (string)
info.product = '1.1 root hub' (string)
info.subsystem = 'usb_device' (string)
info.udi = '/org/freedesktop/Hal/devices/usb_device_1d6b_1_0000_00_1d_1' (string)
info.vendor = 'Linux Foundation' (string)
linux.device_file = '/dev/bus/usb/007/001' (string)
linux.hotplug_type = 2 (0x2) (int)
linux.subsystem = 'usb' (string)
linux.sysfs_path = '/sys/devices/pci0000:00/0000:00:1d.1/usb7' (string)
usb_device.bus_number = 7 (0x7) (int)
usb_device.can_wake_up = true (bool)
usb_device.configuration_value = 1 (0x1) (int)
usb_device.device_class = 9 (0x9) (int)
usb_device.device_protocol = 0 (0x0) (int)
usb_device.device_revision_bcd = 518 (0x206) (int)
usb_device.device_subclass = 0 (0x0) (int)
usb_device.is_self_powered = true (bool)
usb_device.linux.device_number = 1 (0x1) (int)
usb_device.linux.sysfs_path = '/sys/devices/pci0000:00/0000:00:1d.1/usb7' (string)
usb_device.max_power = 0 (0x0) (int)
usb_device.num_configurations = 1 (0x1) (int)
usb_device.num_interfaces = 1 (0x1) (int)
usb_device.num_ports = 2 (0x2) (int)
usb_device.product = '1.1 root hub' (string)
usb_device.product_id = 1 (0x1) (int)
usb_device.serial = '0000:00:1d.1' (string)
usb_device.speed = 12.0 (12) (double)
usb_device.vendor = 'Linux Foundation' (string)
usb_device.vendor_id = 7531 (0x1d6b) (int)
usb_device.version = 1.1 (1.1) (double)
udi = '/org/freedesktop/Hal/devices/usb_device_1d6b_1_0000_00_1d_1_if0'
info.linux.driver = 'hub' (string)
info.parent = '/org/freedesktop/Hal/devices/usb_device_1d6b_1_0000_00_1d_1' (string)
info.product = 'USB Hub Interface' (string)
info.subsystem = 'usb' (string)
info.udi = '/org/freedesktop/Hal/devices/usb_device_1d6b_1_0000_00_1d_1_if0' (string)
linux.hotplug_type = 2 (0x2) (int)
linux.subsystem = 'usb' (string)
linux.sysfs_path = '/sys/devices/pci0000:00/0000:00:1d.1/usb7/7-0:1.0' (string)
usb.bus_number = 7 (0x7) (int)
usb.can_wake_up = true (bool)
usb.configuration_value = 1 (0x1) (int)
usb.device_class = 9 (0x9) (int)
usb.device_protocol = 0 (0x0) (int)
usb.device_revision_bcd = 518 (0x206) (int)
usb.device_subclass = 0 (0x0) (int)
usb.interface.class = 9 (0x9) (int)
usb.interface.number = 0 (0x0) (int)
usb.interface.protocol = 0 (0x0) (int)
usb.interface.subclass = 0 (0x0) (int)
usb.is_self_powered = true (bool)
usb.linux.device_number = 1 (0x1) (int)
usb.linux.sysfs_path = '/sys/devices/pci0000:00/0000:00:1d.1/usb7/7-0:1.0' (string)
usb.max_power = 0 (0x0) (int)
usb.num_configurations = 1 (0x1) (int)
usb.num_interfaces = 1 (0x1) (int)
usb.num_ports = 2 (0x2) (int)
usb.product = 'USB Hub Interface' (string)
usb.product_id = 1 (0x1) (int)
usb.serial = '0000:00:1d.1' (string)
usb.speed = 12.0 (12) (double)
usb.vendor = 'Linux Foundation' (string)
usb.vendor_id = 7531 (0x1d6b) (int)
usb.version = 1.1 (1.1) (double)
udi = '/org/freedesktop/Hal/devices/pci_8086_2934'
info.linux.driver = 'uhci_hcd' (string)
info.parent = '/org/freedesktop/Hal/devices/computer' (string)
info.product = '82801I (ICH9 Family) USB UHCI Controller #1' (string)
info.subsystem = 'pci' (string)
info.udi = '/org/freedesktop/Hal/devices/pci_8086_2934' (string)
info.vendor = 'Intel Corporation' (string)
linux.hotplug_type = 2 (0x2) (int)
linux.subsystem = 'pci' (string)
linux.sysfs_path = '/sys/devices/pci0000:00/0000:00:1d.0' (string)
pci.device_class = 12 (0xc) (int)
pci.device_protocol = 0 (0x0) (int)
pci.device_subclass = 3 (0x3) (int)
pci.linux.sysfs_path = '/sys/devices/pci0000:00/0000:00:1d.0' (string)
pci.product = '82801I (ICH9 Family) USB UHCI Controller #1' (string)
pci.product_id = 10548 (0x2934) (int)
pci.subsys_product_id = 700 (0x2bc) (int)
pci.subsys_vendor = 'Dell' (string)
pci.subsys_vendor_id = 4136 (0x1028) (int)
pci.vendor = 'Intel Corporation' (string)
pci.vendor_id = 32902 (0x8086) (int)
udi = '/org/freedesktop/Hal/devices/usb_device_1d6b_1_0000_00_1d_0'
info.linux.driver = 'usb' (string)
info.parent = '/org/freedesktop/Hal/devices/pci_8086_2934' (string)
info.product = '1.1 root hub' (string)
info.subsystem = 'usb_device' (string)
info.udi = '/org/freedesktop/Hal/devices/usb_device_1d6b_1_0000_00_1d_0' (string)
info.vendor = 'Linux Foundation' (string)
linux.device_file = '/dev/bus/usb/006/001' (string)
linux.hotplug_type = 2 (0x2) (int)
linux.subsystem = 'usb' (string)
linux.sysfs_path = '/sys/devices/pci0000:00/0000:00:1d.0/usb6' (string)
usb_device.bus_number = 6 (0x6) (int)
usb_device.can_wake_up = true (bool)
usb_device.configuration_value = 1 (0x1) (int)
usb_device.device_class = 9 (0x9) (int)
usb_device.device_protocol = 0 (0x0) (int)
usb_device.device_revision_bcd = 518 (0x206) (int)
usb_device.device_subclass = 0 (0x0) (int)
usb_device.is_self_powered = true (bool)
usb_device.linux.device_number = 1 (0x1) (int)
usb_device.linux.sysfs_path = '/sys/devices/pci0000:00/0000:00:1d.0/usb6' (string)
usb_device.max_power = 0 (0x0) (int)
usb_device.num_configurations = 1 (0x1) (int)
usb_device.num_interfaces = 1 (0x1) (int)
usb_device.num_ports = 2 (0x2) (int)
usb_device.product = '1.1 root hub' (string)
usb_device.product_id = 1 (0x1) (int)
usb_device.serial = '0000:00:1d.0' (string)
usb_device.speed = 12.0 (12) (double)
usb_device.vendor = 'Linux Foundation' (string)
usb_device.vendor_id = 7531 (0x1d6b) (int)
usb_device.version = 1.1 (1.1) (double)
udi = '/org/freedesktop/Hal/devices/usb_device_1d6b_1_0000_00_1d_0_if0'
info.linux.driver = 'hub' (string)
info.parent = '/org/freedesktop/Hal/devices/usb_device_1d6b_1_0000_00_1d_0' (string)
info.product = 'USB Hub Interface' (string)
info.subsystem = 'usb' (string)
info.udi = '/org/freedesktop/Hal/devices/usb_device_1d6b_1_0000_00_1d_0_if0' (string)
linux.hotplug_type = 2 (0x2) (int)
linux.subsystem = 'usb' (string)
linux.sysfs_path = '/sys/devices/pci0000:00/0000:00:1d.0/usb6/6-0:1.0' (string)
usb.bus_number = 6 (0x6) (int)
usb.can_wake_up = true (bool)
usb.configuration_value = 1 (0x1) (int)
usb.device_class = 9 (0x9) (int)
usb.device_protocol = 0 (0x0) (int)
usb.device_revision_bcd = 518 (0x206) (int)
usb.device_subclass = 0 (0x0) (int)
usb.interface.class = 9 (0x9) (int)
usb.interface.number = 0 (0x0) (int)
usb.interface.protocol = 0 (0x0) (int)
usb.interface.subclass = 0 (0x0) (int)
usb.is_self_powered = true (bool)
usb.linux.device_number = 1 (0x1) (int)
usb.linux.sysfs_path = '/sys/devices/pci0000:00/0000:00:1d.0/usb6/6-0:1.0' (string)
usb.max_power = 0 (0x0) (int)
usb.num_configurations = 1 (0x1) (int)
usb.num_interfaces = 1 (0x1) (int)
usb.num_ports = 2 (0x2) (int)
usb.product = 'USB Hub Interface' (string)
usb.product_id = 1 (0x1) (int)
usb.serial = '0000:00:1d.0' (string)
usb.speed = 12.0 (12) (double)
usb.vendor = 'Linux Foundation' (string)
usb.vendor_id = 7531 (0x1d6b) (int)
usb.version = 1.1 (1.1) (double)
udi = '/org/freedesktop/Hal/devices/pci_8086_294a'
info.linux.driver = 'pcieport-driver' (string)
info.parent = '/org/freedesktop/Hal/devices/computer' (string)
info.product = '82801I (ICH9 Family) PCI Express Port 6' (string)
info.subsystem = 'pci' (string)
info.udi = '/org/freedesktop/Hal/devices/pci_8086_294a' (string)
info.vendor = 'Intel Corporation' (string)
linux.hotplug_type = 2 (0x2) (int)
linux.subsystem = 'pci' (string)
linux.sysfs_path = '/sys/devices/pci0000:00/0000:00:1c.5' (string)
pci.device_class = 6 (0x6) (int)
pci.device_protocol = 0 (0x0) (int)
pci.device_subclass = 4 (0x4) (int)
pci.linux.sysfs_path = '/sys/devices/pci0000:00/0000:00:1c.5' (string)
pci.product = '82801I (ICH9 Family) PCI Express Port 6' (string)
pci.product_id = 10570 (0x294a) (int)
pci.subsys_product_id = 0 (0x0) (int)
pci.subsys_vendor_id = 0 (0x0) (int)
pci.vendor = 'Intel Corporation' (string)
pci.vendor_id = 32902 (0x8086) (int)
udi = '/org/freedesktop/Hal/devices/pci_8086_2948'
info.linux.driver = 'pcieport-driver' (string)
info.parent = '/org/freedesktop/Hal/devices/computer' (string)
info.product = '82801I (ICH9 Family) PCI Express Port 5' (string)
info.subsystem = 'pci' (string)
info.udi = '/org/freedesktop/Hal/devices/pci_8086_2948' (string)
info.vendor = 'Intel Corporation' (string)
linux.hotplug_type = 2 (0x2) (int)
linux.subsystem = 'pci' (string)
linux.sysfs_path = '/sys/devices/pci0000:00/0000:00:1c.4' (string)
pci.device_class = 6 (0x6) (int)
pci.device_protocol = 0 (0x0) (int)
pci.device_subclass = 4 (0x4) (int)
pci.linux.sysfs_path = '/sys/devices/pci0000:00/0000:00:1c.4' (string)
pci.product = '82801I (ICH9 Family) PCI Express Port 5' (string)
pci.product_id = 10568 (0x2948) (int)
pci.subsys_product_id = 0 (0x0) (int)
pci.subsys_vendor_id = 0 (0x0) (int)
pci.vendor = 'Intel Corporation' (string)
pci.vendor_id = 32902 (0x8086) (int)
udi = '/org/freedesktop/Hal/devices/pci_1217_8130'
info.parent = '/org/freedesktop/Hal/devices/pci_8086_2948' (string)
info.product = 'Unknown (0x8130)' (string)
info.subsystem = 'pci' (string)
info.udi = '/org/freedesktop/Hal/devices/pci_1217_8130' (string)
info.vendor = 'O2 Micro, Inc.' (string)
linux.hotplug_type = 2 (0x2) (int)
linux.subsystem = 'pci' (string)
linux.sysfs_path = '/sys/devices/pci0000:00/0000:00:1c.4/0000:1a:00.2' (string)
pci.device_class = 1 (0x1) (int)
pci.device_protocol = 0 (0x0) (int)
pci.device_subclass = 128 (0x80) (int)
pci.linux.sysfs_path = '/sys/devices/pci0000:00/0000:00:1c.4/0000:1a:00.2' (string)
pci.product_id = 33072 (0x8130) (int)
pci.subsys_product_id = 700 (0x2bc) (int)
pci.subsys_vendor = 'Dell' (string)
pci.subsys_vendor_id = 4136 (0x1028) (int)
pci.vendor = 'O2 Micro, Inc.' (string)
pci.vendor_id = 4631 (0x1217) (int)
udi = '/org/freedesktop/Hal/devices/pci_1217_8120'
info.linux.driver = 'sdhci-pci' (string)
info.parent = '/org/freedesktop/Hal/devices/pci_8086_2948' (string)
info.product = 'Unknown (0x8120)' (string)
info.subsystem = 'pci' (string)
info.udi = '/org/freedesktop/Hal/devices/pci_1217_8120' (string)
info.vendor = 'O2 Micro, Inc.' (string)
linux.hotplug_type = 2 (0x2) (int)
linux.subsystem = 'pci' (string)
linux.sysfs_path = '/sys/devices/pci0000:00/0000:00:1c.4/0000:1a:00.1' (string)
pci.device_class = 8 (0x8) (int)
pci.device_protocol = 0 (0x0) (int)
pci.device_subclass = 5 (0x5) (int)
pci.linux.sysfs_path = '/sys/devices/pci0000:00/0000:00:1c.4/0000:1a:00.1' (string)
pci.product_id = 33056 (0x8120) (int)
pci.subsys_product_id = 700 (0x2bc) (int)
pci.subsys_vendor = 'Dell' (string)
pci.subsys_vendor_id = 4136 (0x1028) (int)
pci.vendor = 'O2 Micro, Inc.' (string)
pci.vendor_id = 4631 (0x1217) (int)
udi = '/org/freedesktop/Hal/devices/pci_1217_8120_mmc_host'
info.capabilities = {'mmc_host'} (string list)
info.category = 'mmc_host' (string)
info.parent = '/org/freedesktop/Hal/devices/pci_1217_8120' (string)
info.product = 'MMC/SD Host Adapter' (string)
info.subsystem = 'mmc_host' (string)
info.udi = '/org/freedesktop/Hal/devices/pci_1217_8120_mmc_host' (string)
linux.hotplug_type = 2 (0x2) (int)
linux.subsystem = 'mmc_host' (string)
linux.sysfs_path = '/sys/devices/pci0000:00/0000:00:1c.4/0000:1a:00.1/mmc_host/mmc0' (string)
mmc_host.host = 0 (0x0) (int)
udi = '/org/freedesktop/Hal/devices/pci_1217_10f7'
info.linux.driver = 'ohci1394' (string)
info.parent = '/org/freedesktop/Hal/devices/pci_8086_2948' (string)
info.product = 'Unknown (0x10f7)' (string)
info.subsystem = 'pci' (string)
info.udi = '/org/freedesktop/Hal/devices/pci_1217_10f7' (string)
info.vendor = 'O2 Micro, Inc.' (string)
linux.hotplug_type = 2 (0x2) (int)
linux.subsystem = 'pci' (string)
linux.sysfs_path = '/sys/devices/pci0000:00/0000:00:1c.4/0000:1a:00.0' (string)
pci.device_class = 12 (0xc) (int)
pci.device_protocol = 16 (0x10) (int)
pci.device_subclass = 0 (0x0) (int)
pci.linux.sysfs_path = '/sys/devices/pci0000:00/0000:00:1c.4/0000:1a:00.0' (string)
pci.product_id = 4343 (0x10f7) (int)
pci.subsys_product_id = 700 (0x2bc) (int)
pci.subsys_vendor = 'Dell' (string)
pci.subsys_vendor_id = 4136 (0x1028) (int)
pci.vendor = 'O2 Micro, Inc.' (string)
pci.vendor_id = 4631 (0x1217) (int)
udi = '/org/freedesktop/Hal/devices/pci_8086_2946'
info.linux.driver = 'pcieport-driver' (string)
info.parent = '/org/freedesktop/Hal/devices/computer' (string)
info.product = '82801I (ICH9 Family) PCI Express Port 4' (string)
info.subsystem = 'pci' (string)
info.udi = '/org/freedesktop/Hal/devices/pci_8086_2946' (string)
info.vendor = 'Intel Corporation' (string)
linux.hotplug_type = 2 (0x2) (int)
linux.subsystem = 'pci' (string)
linux.sysfs_path = '/sys/devices/pci0000:00/0000:00:1c.3' (string)
pci.device_class = 6 (0x6) (int)
pci.device_protocol = 0 (0x0) (int)
pci.device_subclass = 4 (0x4) (int)
pci.linux.sysfs_path = '/sys/devices/pci0000:00/0000:00:1c.3' (string)
pci.product = '82801I (ICH9 Family) PCI Express Port 4' (string)
pci.product_id = 10566 (0x2946) (int)
pci.subsys_product_id = 0 (0x0) (int)
pci.subsys_vendor_id = 0 (0x0) (int)
pci.vendor = 'Intel Corporation' (string)
pci.vendor_id = 32902 (0x8086) (int)
udi = '/org/freedesktop/Hal/devices/pci_8086_2944'
info.linux.driver = 'pcieport-driver' (string)
info.parent = '/org/freedesktop/Hal/devices/computer' (string)
info.product = '82801I (ICH9 Family) PCI Express Port 3' (string)
info.subsystem = 'pci' (string)
info.udi = '/org/freedesktop/Hal/devices/pci_8086_2944' (string)
info.vendor = 'Intel Corporation' (string)
linux.hotplug_type = 2 (0x2) (int)
linux.subsystem = 'pci' (string)
linux.sysfs_path = '/sys/devices/pci0000:00/0000:00:1c.2' (string)
pci.device_class = 6 (0x6) (int)
pci.device_protocol = 0 (0x0) (int)
pci.device_subclass = 4 (0x4) (int)
pci.linux.sysfs_path = '/sys/devices/pci0000:00/0000:00:1c.2' (string)
pci.product = '82801I (ICH9 Family) PCI Express Port 3' (string)
pci.product_id = 10564 (0x2944) (int)
pci.subsys_product_id = 0 (0x0) (int)
pci.subsys_vendor_id = 0 (0x0) (int)
pci.vendor = 'Intel Corporation' (string)
pci.vendor_id = 32902 (0x8086) (int)
udi = '/org/freedesktop/Hal/devices/pci_8086_4232'
info.linux.driver = 'iwlagn' (string)
info.parent = '/org/freedesktop/Hal/devices/pci_8086_2944' (string)
info.product = 'Wireless WiFi Link 5100' (string)
info.subsystem = 'pci' (string)
info.udi = '/org/freedesktop/Hal/devices/pci_8086_4232' (string)
info.vendor = 'Intel Corporation' (string)
linux.hotplug_type = 2 (0x2) (int)
linux.subsystem = 'pci' (string)
linux.sysfs_path = '/sys/devices/pci0000:00/0000:00:1c.2/0000:0e:00.0' (string)
pci.device_class = 2 (0x2) (int)
pci.device_protocol = 0 (0x0) (int)
pci.device_subclass = 128 (0x80) (int)
pci.linux.sysfs_path = '/sys/devices/pci0000:00/0000:00:1c.2/0000:0e:00.0' (string)
pci.product = 'Wireless WiFi Link 5100' (string)
pci.product_id = 16946 (0x4232) (int)
pci.subsys_product_id = 4897 (0x1321) (int)
pci.subsys_vendor = 'Intel Corporation' (string)
pci.subsys_vendor_id = 32902 (0x8086) (int)
pci.vendor = 'Intel Corporation' (string)
pci.vendor_id = 32902 (0x8086) (int)
udi = '/org/freedesktop/Hal/devices/leds_iwl_phy0_2'
info.capabilities = {'leds'} (string list)
info.category = 'leds' (string)
info.parent = '/org/freedesktop/Hal/devices/pci_8086_4232' (string)
info.subsystem = 'leds' (string)
info.udi = '/org/freedesktop/Hal/devices/leds_iwl_phy0_2' (string)
leds.colour = 'TX' (string)
leds.device_name = 'iwl-phy0' (string)
linux.hotplug_type = 2 (0x2) (int)
linux.subsystem = 'leds' (string)
linux.sysfs_path = '/sys/devices/pci0000:00/0000:00:1c.2/0000:0e:00.0/leds/iwl-phy0:TX' (string)
udi = '/org/freedesktop/Hal/devices/leds_iwl_phy0_1'
info.capabilities = {'leds'} (string list)
info.category = 'leds' (string)
info.parent = '/org/freedesktop/Hal/devices/pci_8086_4232' (string)
info.subsystem = 'leds' (string)
info.udi = '/org/freedesktop/Hal/devices/leds_iwl_phy0_1' (string)
leds.colour = 'assoc' (string)
leds.device_name = 'iwl-phy0' (string)
linux.hotplug_type = 2 (0x2) (int)
linux.subsystem = 'leds' (string)
linux.sysfs_path = '/sys/devices/pci0000:00/0000:00:1c.2/0000:0e:00.0/leds/iwl-phy0:assoc' (string)
udi = '/org/freedesktop/Hal/devices/leds_iwl_phy0_0'
info.capabilities = {'leds'} (string list)
info.category = 'leds' (string)
info.parent = '/org/freedesktop/Hal/devices/pci_8086_4232' (string)
info.subsystem = 'leds' (string)
info.udi = '/org/freedesktop/Hal/devices/leds_iwl_phy0_0' (string)
leds.colour = 'RX' (string)
leds.device_name = 'iwl-phy0' (string)
linux.hotplug_type = 2 (0x2) (int)
linux.subsystem = 'leds' (string)
linux.sysfs_path = '/sys/devices/pci0000:00/0000:00:1c.2/0000:0e:00.0/leds/iwl-phy0:RX' (string)
udi = '/org/freedesktop/Hal/devices/leds_iwl_phy0'
info.capabilities = {'leds'} (string list)
info.category = 'leds' (string)
info.parent = '/org/freedesktop/Hal/devices/pci_8086_4232' (string)
info.subsystem = 'leds' (string)
info.udi = '/org/freedesktop/Hal/devices/leds_iwl_phy0' (string)
leds.colour = 'radio' (string)
leds.device_name = 'iwl-phy0' (string)
linux.hotplug_type = 2 (0x2) (int)
linux.subsystem = 'leds' (string)
linux.sysfs_path = '/sys/devices/pci0000:00/0000:00:1c.2/0000:0e:00.0/leds/iwl-phy0:radio' (string)
udi = '/org/freedesktop/Hal/devices/pci_8086_4232_rfkill_5100AGN_wlan'
info.addons.singleton = {'hald-addon-rfkill-killswitch'} (string list)
info.capabilities = {'killswitch'} (string list)
info.category = 'killswitch' (string)
info.interfaces = {'org.freedesktop.Hal.Device.KillSwitch'} (string list)
info.parent = '/org/freedesktop/Hal/devices/pci_8086_4232' (string)
info.product = '5100AGN wlan Killswitch' (string)
info.subsystem = 'rfkill' (string)
info.udi = '/org/freedesktop/Hal/devices/pci_8086_4232_rfkill_5100AGN_wlan' (string)
info.vendor = 'Intel Corporation' (string)
killswitch.access_method = 'rfkill' (string)
killswitch.name = '5100AGN' (string)
killswitch.state = 1 (0x1) (int)
killswitch.type = 'wlan' (string)
linux.hotplug_type = 2 (0x2) (int)
linux.subsystem = 'rfkill' (string)
linux.sysfs_path = '/sys/devices/pci0000:00/0000:00:1c.2/0000:0e:00.0/rfkill/rfkill0' (string)
udi = '/org/freedesktop/Hal/devices/net_00_22_fb_ab_b8_54_0'
info.capabilities = {'net', 'net.80211control'} (string list)
info.category = 'net.80211control' (string)
info.parent = '/org/freedesktop/Hal/devices/pci_8086_4232' (string)
info.product = 'Networking Wireless Control Interface' (string)
info.subsystem = 'net' (string)
info.udi = '/org/freedesktop/Hal/devices/net_00_22_fb_ab_b8_54_0' (string)
linux.hotplug_type = 2 (0x2) (int)
linux.subsystem = 'net' (string)
linux.sysfs_path = '/sys/devices/pci0000:00/0000:00:1c.2/0000:0e:00.0/net/wmaster0' (string)
net.address = '00:22:fb:ab:b8:54' (string)
net.arp_proto_hw_id = 801 (0x321) (int)
net.interface = 'wmaster0' (string)
net.linux.ifindex = 3 (0x3) (int)
net.originating_device = '/org/freedesktop/Hal/devices/pci_8086_4232' (string)
udi = '/org/freedesktop/Hal/devices/net_00_22_fb_ab_b8_54'
info.capabilities = {'net', 'net.80211'} (string list)
info.category = 'net.80211' (string)
info.parent = '/org/freedesktop/Hal/devices/pci_8086_4232' (string)
info.product = 'WLAN Interface' (string)
info.subsystem = 'net' (string)
info.udi = '/org/freedesktop/Hal/devices/net_00_22_fb_ab_b8_54' (string)
linux.hotplug_type = 2 (0x2) (int)
linux.subsystem = 'net' (string)
linux.sysfs_path = '/sys/devices/pci0000:00/0000:00:1c.2/0000:0e:00.0/net/wlan0' (string)
net.80211.mac_address = 150251223124 (0x22fbabb854) (uint64)
net.address = '00:22:fb:ab:b8:54' (string)
net.arp_proto_hw_id = 1 (0x1) (int)
net.interface = 'wlan0' (string)
net.linux.ifindex = 4 (0x4) (int)
net.originating_device = '/org/freedesktop/Hal/devices/pci_8086_4232' (string)
udi = '/org/freedesktop/Hal/devices/pci_8086_2942'
info.linux.driver = 'pcieport-driver' (string)
info.parent = '/org/freedesktop/Hal/devices/computer' (string)
info.product = '82801I (ICH9 Family) PCI Express Port 2' (string)
info.subsystem = 'pci' (string)
info.udi = '/org/freedesktop/Hal/devices/pci_8086_2942' (string)
info.vendor = 'Intel Corporation' (string)
linux.hotplug_type = 2 (0x2) (int)
linux.subsystem = 'pci' (string)
linux.sysfs_path = '/sys/devices/pci0000:00/0000:00:1c.1' (string)
pci.device_class = 6 (0x6) (int)
pci.device_protocol = 0 (0x0) (int)
pci.device_subclass = 4 (0x4) (int)
pci.linux.sysfs_path = '/sys/devices/pci0000:00/0000:00:1c.1' (string)
pci.product = '82801I (ICH9 Family) PCI Express Port 2' (string)
pci.product_id = 10562 (0x2942) (int)
pci.subsys_product_id = 0 (0x0) (int)
pci.subsys_vendor_id = 0 (0x0) (int)
pci.vendor = 'Intel Corporation' (string)
pci.vendor_id = 32902 (0x8086) (int)
udi = '/org/freedesktop/Hal/devices/pci_10ec_8168'
info.linux.driver = 'r8169' (string)
info.parent = '/org/freedesktop/Hal/devices/pci_8086_2942' (string)
info.product = 'RTL8111/8168B PCI Express Gigabit Ethernet controller' (string)
info.subsystem = 'pci' (string)
info.udi = '/org/freedesktop/Hal/devices/pci_10ec_8168' (string)
info.vendor = 'Realtek Semiconductor Co., Ltd.' (string)
linux.hotplug_type = 2 (0x2) (int)
linux.subsystem = 'pci' (string)
linux.sysfs_path = '/sys/devices/pci0000:00/0000:00:1c.1/0000:08:00.0' (string)
pci.device_class = 2 (0x2) (int)
pci.device_protocol = 0 (0x0) (int)
pci.device_subclass = 0 (0x0) (int)
pci.linux.sysfs_path = '/sys/devices/pci0000:00/0000:00:1c.1/0000:08:00.0' (string)
pci.product = 'RTL8111/8168B PCI Express Gigabit Ethernet controller' (string)
pci.product_id = 33128 (0x8168) (int)
pci.subsys_product_id = 700 (0x2bc) (int)
pci.subsys_vendor = 'Dell' (string)
pci.subsys_vendor_id = 4136 (0x1028) (int)
pci.vendor = 'Realtek Semiconductor Co., Ltd.' (string)
pci.vendor_id = 4332 (0x10ec) (int)
udi = '/org/freedesktop/Hal/devices/net_00_24_e8_c2_9e_5b'
info.capabilities = {'net', 'net.80203', 'wake_on_lan'} (string list)
info.category = 'net.80203' (string)
info.interfaces = {'org.freedesktop.Hal.Device.WakeOnLan'} (string list)
info.parent = '/org/freedesktop/Hal/devices/pci_10ec_8168' (string)
info.product = 'Networking Interface' (string)
info.subsystem = 'net' (string)
info.udi = '/org/freedesktop/Hal/devices/net_00_24_e8_c2_9e_5b' (string)
linux.hotplug_type = 2 (0x2) (int)
linux.subsystem = 'net' (string)
linux.sysfs_path = '/sys/devices/pci0000:00/0000:00:1c.1/0000:08:00.0/net/eth0' (string)
net.80203.mac_address = 158523891291 (0x24e8c29e5b) (uint64)
net.address = '00:24:e8:c2:9e:5b' (string)
net.arp_proto_hw_id = 1 (0x1) (int)
net.interface = 'eth0' (string)
net.linux.ifindex = 2 (0x2) (int)
net.originating_device = '/org/freedesktop/Hal/devices/pci_10ec_8168' (string)
org.freedesktop.Hal.Device.WakeOnLan.method_argnames = {'', '', 'enable'} (string list)
org.freedesktop.Hal.Device.WakeOnLan.method_execpaths = {'hal-system-wol-supported', 'hal-system-wol-enabled', 'hal-system-wol-enable'} (string list)
org.freedesktop.Hal.Device.WakeOnLan.method_names = {'GetSupported', 'GetEnabled', 'SetEnabled'} (string list)
org.freedesktop.Hal.Device.WakeOnLan.method_signatures = {'', '', 'b'} (string list)
udi = '/org/freedesktop/Hal/devices/pci_8086_2940'
info.linux.driver = 'pcieport-driver' (string)
info.parent = '/org/freedesktop/Hal/devices/computer' (string)
info.product = '82801I (ICH9 Family) PCI Express Port 1' (string)
info.subsystem = 'pci' (string)
info.udi = '/org/freedesktop/Hal/devices/pci_8086_2940' (string)
info.vendor = 'Intel Corporation' (string)
linux.hotplug_type = 2 (0x2) (int)
linux.subsystem = 'pci' (string)
linux.sysfs_path = '/sys/devices/pci0000:00/0000:00:1c.0' (string)
pci.device_class = 6 (0x6) (int)
pci.device_protocol = 0 (0x0) (int)
pci.device_subclass = 4 (0x4) (int)
pci.linux.sysfs_path = '/sys/devices/pci0000:00/0000:00:1c.0' (string)
pci.product = '82801I (ICH9 Family) PCI Express Port 1' (string)
pci.product_id = 10560 (0x2940) (int)
pci.subsys_product_id = 0 (0x0) (int)
pci.subsys_vendor_id = 0 (0x0) (int)
pci.vendor = 'Intel Corporation' (string)
pci.vendor_id = 32902 (0x8086) (int)
udi = '/org/freedesktop/Hal/devices/pci_8086_293e'
info.linux.driver = 'HDA Intel' (string)
info.parent = '/org/freedesktop/Hal/devices/computer' (string)
info.product = '82801I (ICH9 Family) HD Audio Controller' (string)
info.subsystem = 'pci' (string)
info.udi = '/org/freedesktop/Hal/devices/pci_8086_293e' (string)
info.vendor = 'Intel Corporation' (string)
linux.hotplug_type = 2 (0x2) (int)
linux.subsystem = 'pci' (string)
linux.sysfs_path = '/sys/devices/pci0000:00/0000:00:1b.0' (string)
pci.device_class = 4 (0x4) (int)
pci.device_protocol = 0 (0x0) (int)
pci.device_subclass = 3 (0x3) (int)
pci.linux.sysfs_path = '/sys/devices/pci0000:00/0000:00:1b.0' (string)
pci.product = '82801I (ICH9 Family) HD Audio Controller' (string)
pci.product_id = 10558 (0x293e) (int)
pci.subsys_product_id = 700 (0x2bc) (int)
pci.subsys_vendor = 'Dell' (string)
pci.subsys_vendor_id = 4136 (0x1028) (int)
pci.vendor = 'Intel Corporation' (string)
pci.vendor_id = 32902 (0x8086) (int)
udi = '/org/freedesktop/Hal/devices/pci_8086_293e_sound_card_0'
info.capabilities = {'sound'} (string list)
info.category = 'sound' (string)
info.parent = '/org/freedesktop/Hal/devices/pci_8086_293e' (string)
info.product = 'HDA Intel Sound Card' (string)
info.subsystem = 'sound' (string)
info.udi = '/org/freedesktop/Hal/devices/pci_8086_293e_sound_card_0' (string)
linux.hotplug_type = 2 (0x2) (int)
linux.subsystem = 'sound' (string)
linux.sysfs_path = '/sys/devices/pci0000:00/0000:00:1b.0/sound/card0' (string)
sound.card = 0 (0x0) (int)
sound.card_id = 'HDA Intel' (string)
sound.originating_device = '/org/freedesktop/Hal/devices/pci_8086_293e' (string)
udi = '/org/freedesktop/Hal/devices/pci_8086_293e_sound_card_0_alsa_playback_0'
access_control.file = '/dev/snd/pcmC0D0p' (string)
access_control.type = 'sound' (string)
alsa.card = 0 (0x0) (int)
alsa.card_id = 'HDA Intel' (string)
alsa.device = 0 (0x0) (int)
alsa.device_file = '/dev/snd/pcmC0D0p' (string)
alsa.device_id = 'HDA Generic' (string)
alsa.originating_device = '/org/freedesktop/Hal/devices/pci_8086_293e_sound_card_0' (string)
alsa.pcm_class = 'generic' (string)
alsa.type = 'playback' (string)
info.callouts.add = {'hal-acl-tool --add-device'} (string list)
info.callouts.remove = {'hal-acl-tool --remove-device'} (string list)
info.capabilities = {'alsa', 'access_control'} (string list)
info.category = 'alsa' (string)
info.parent = '/org/freedesktop/Hal/devices/pci_8086_293e_sound_card_0' (string)
info.product = 'HDA Generic ALSA Playback Device' (string)
info.subsystem = 'sound' (string)
info.udi = '/org/freedesktop/Hal/devices/pci_8086_293e_sound_card_0_alsa_playback_0' (string)
linux.device_file = '/dev/snd/pcmC0D0p' (string)
linux.hotplug_type = 2 (0x2) (int)
linux.subsystem = 'sound' (string)
linux.sysfs_path = '/sys/devices/pci0000:00/0000:00:1b.0/sound/card0/pcmC0D0p' (string)
udi = '/org/freedesktop/Hal/devices/pci_8086_293e_sound_card_0_alsa_capture_0'
access_control.file = '/dev/snd/pcmC0D0c' (string)
access_control.type = 'sound' (string)
alsa.card = 0 (0x0) (int)
alsa.card_id = 'HDA Intel' (string)
alsa.device = 0 (0x0) (int)
alsa.device_file = '/dev/snd/pcmC0D0c' (string)
alsa.device_id = 'HDA Generic' (string)
alsa.originating_device = '/org/freedesktop/Hal/devices/pci_8086_293e_sound_card_0' (string)
alsa.pcm_class = 'generic' (string)
alsa.type = 'capture' (string)
info.callouts.add = {'hal-acl-tool --add-device'} (string list)
info.callouts.remove = {'hal-acl-tool --remove-device'} (string list)
info.capabilities = {'alsa', 'access_control'} (string list)
info.category = 'alsa' (string)
info.parent = '/org/freedesktop/Hal/devices/pci_8086_293e_sound_card_0' (string)
info.product = 'HDA Generic ALSA Capture Device' (string)
info.subsystem = 'sound' (string)
info.udi = '/org/freedesktop/Hal/devices/pci_8086_293e_sound_card_0_alsa_capture_0' (string)
linux.device_file = '/dev/snd/pcmC0D0c' (string)
linux.hotplug_type = 2 (0x2) (int)
linux.subsystem = 'sound' (string)
linux.sysfs_path = '/sys/devices/pci0000:00/0000:00:1b.0/sound/card0/pcmC0D0c' (string)
udi = '/org/freedesktop/Hal/devices/pci_8086_293e_sound_card_0_oss_mixer__1'
access_control.file = '/dev/mixer' (string)
access_control.type = 'sound' (string)
info.callouts.add = {'hal-acl-tool --add-device'} (string list)
info.callouts.remove = {'hal-acl-tool --remove-device'} (string list)
info.capabilities = {'oss', 'access_control'} (string list)
info.category = 'oss' (string)
info.parent = '/org/freedesktop/Hal/devices/pci_8086_293e_sound_card_0' (string)
info.product = 'HDA Generic OSS Control Device' (string)
info.subsystem = 'sound' (string)
info.udi = '/org/freedesktop/Hal/devices/pci_8086_293e_sound_card_0_oss_mixer__1' (string)
linux.device_file = '/dev/mixer' (string)
linux.hotplug_type = 2 (0x2) (int)
linux.subsystem = 'sound' (string)
linux.sysfs_path = '/sys/devices/pci0000:00/0000:00:1b.0/sound/card0/mixer' (string)
oss.card = 0 (0x0) (int)
oss.card_id = 'HDA Intel' (string)
oss.device_file = '/dev/mixer' (string)
oss.device_id = 'HDA Generic' (string)
oss.originating_device = '/org/freedesktop/Hal/devices/pci_8086_293e_sound_card_0' (string)
oss.type = 'mixer' (string)
udi = '/org/freedesktop/Hal/devices/pci_8086_293e_sound_card_0_oss_pcm_0_0'
access_control.file = '/dev/dsp' (string)
access_control.type = 'sound' (string)
info.callouts.add = {'hal-acl-tool --add-device'} (string list)
info.callouts.remove = {'hal-acl-tool --remove-device'} (string list)
info.capabilities = {'oss', 'access_control'} (string list)
info.category = 'oss' (string)
info.parent = '/org/freedesktop/Hal/devices/pci_8086_293e_sound_card_0' (string)
info.product = 'HDA Generic OSS PCM Device' (string)
info.subsystem = 'sound' (string)
info.udi = '/org/freedesktop/Hal/devices/pci_8086_293e_sound_card_0_oss_pcm_0_0' (string)
linux.device_file = '/dev/dsp' (string)
linux.hotplug_type = 2 (0x2) (int)
linux.subsystem = 'sound' (string)
linux.sysfs_path = '/sys/devices/pci0000:00/0000:00:1b.0/sound/card0/dsp' (string)
oss.card = 0 (0x0) (int)
oss.card_id = 'HDA Intel' (string)
oss.device = 0 (0x0) (int)
oss.device_file = '/dev/dsp' (string)
oss.device_id = 'HDA Generic' (string)
oss.originating_device = '/org/freedesktop/Hal/devices/pci_8086_293e_sound_card_0' (string)
oss.type = 'pcm' (string)
udi = '/org/freedesktop/Hal/devices/pci_8086_293e_sound_card_0_alsa_control__1'
access_control.file = '/dev/snd/controlC0' (string)
access_control.type = 'sound' (string)
alsa.card = 0 (0x0) (int)
alsa.card_id = 'HDA Intel' (string)
alsa.device_file = '/dev/snd/controlC0' (string)
alsa.originating_device = '/org/freedesktop/Hal/devices/pci_8086_293e_sound_card_0' (string)
alsa.type = 'control' (string)
info.callouts.add = {'hal-acl-tool --add-device'} (string list)
info.callouts.remove = {'hal-acl-tool --remove-device'} (string list)
info.capabilities = {'alsa', 'access_control'} (string list)
info.category = 'alsa' (string)
info.parent = '/org/freedesktop/Hal/devices/pci_8086_293e_sound_card_0' (string)
info.product = 'HDA Intel ALSA Control Device' (string)
info.subsystem = 'sound' (string)
info.udi = '/org/freedesktop/Hal/devices/pci_8086_293e_sound_card_0_alsa_control__1' (string)
linux.device_file = '/dev/snd/controlC0' (string)
linux.hotplug_type = 2 (0x2) (int)
linux.subsystem = 'sound' (string)
linux.sysfs_path = '/sys/devices/pci0000:00/0000:00:1b.0/sound/card0/controlC0' (string)
udi = '/org/freedesktop/Hal/devices/pci_8086_293e_sound_card_0_oss_pcm_0'
access_control.file = '/dev/audio' (string)
access_control.type = 'sound' (string)
info.callouts.add = {'hal-acl-tool --add-device'} (string list)
info.callouts.remove = {'hal-acl-tool --remove-device'} (string list)
info.capabilities = {'oss', 'access_control'} (string list)
info.category = 'oss' (string)
info.parent = '/org/freedesktop/Hal/devices/pci_8086_293e_sound_card_0' (string)
info.product = 'HDA Generic OSS PCM Device' (string)
info.subsystem = 'sound' (string)
info.udi = '/org/freedesktop/Hal/devices/pci_8086_293e_sound_card_0_oss_pcm_0' (string)
linux.device_file = '/dev/audio' (string)
linux.hotplug_type = 2 (0x2) (int)
linux.subsystem = 'sound' (string)
linux.sysfs_path = '/sys/devices/pci0000:00/0000:00:1b.0/sound/card0/audio' (string)
oss.card = 0 (0x0) (int)
oss.card_id = 'HDA Intel' (string)
oss.device = 0 (0x0) (int)
oss.device_file = '/dev/audio' (string)
oss.device_id = 'HDA Generic' (string)
oss.originating_device = '/org/freedesktop/Hal/devices/pci_8086_293e_sound_card_0' (string)
oss.type = 'pcm' (string)
udi = '/org/freedesktop/Hal/devices/pci_8086_293c'
info.linux.driver = 'ehci_hcd' (string)
info.parent = '/org/freedesktop/Hal/devices/computer' (string)
info.product = '82801I (ICH9 Family) USB2 EHCI Controller #2' (string)
info.subsystem = 'pci' (string)
info.udi = '/org/freedesktop/Hal/devices/pci_8086_293c' (string)
info.vendor = 'Intel Corporation' (string)
linux.hotplug_type = 2 (0x2) (int)
linux.subsystem = 'pci' (string)
linux.sysfs_path = '/sys/devices/pci0000:00/0000:00:1a.7' (string)
pci.device_class = 12 (0xc) (int)
pci.device_protocol = 32 (0x20) (int)
pci.device_subclass = 3 (0x3) (int)
pci.linux.sysfs_path = '/sys/devices/pci0000:00/0000:00:1a.7' (string)
pci.product = '82801I (ICH9 Family) USB2 EHCI Controller #2' (string)
pci.product_id = 10556 (0x293c) (int)
pci.subsys_product_id = 700 (0x2bc) (int)
pci.subsys_vendor = 'Dell' (string)
pci.subsys_vendor_id = 4136 (0x1028) (int)
pci.vendor = 'Intel Corporation' (string)
pci.vendor_id = 32902 (0x8086) (int)
udi = '/org/freedesktop/Hal/devices/usb_device_1d6b_2_0000_00_1a_7'
info.linux.driver = 'usb' (string)
info.parent = '/org/freedesktop/Hal/devices/pci_8086_293c' (string)
info.product = '2.0 root hub' (string)
info.subsystem = 'usb_device' (string)
info.udi = '/org/freedesktop/Hal/devices/usb_device_1d6b_2_0000_00_1a_7' (string)
info.vendor = 'Linux Foundation' (string)
linux.device_file = '/dev/bus/usb/001/001' (string)
linux.hotplug_type = 2 (0x2) (int)
linux.subsystem = 'usb' (string)
linux.sysfs_path = '/sys/devices/pci0000:00/0000:00:1a.7/usb1' (string)
usb_device.bus_number = 1 (0x1) (int)
usb_device.can_wake_up = true (bool)
usb_device.configuration_value = 1 (0x1) (int)
usb_device.device_class = 9 (0x9) (int)
usb_device.device_protocol = 0 (0x0) (int)
usb_device.device_revision_bcd = 518 (0x206) (int)
usb_device.device_subclass = 0 (0x0) (int)
usb_device.is_self_powered = true (bool)
usb_device.linux.device_number = 1 (0x1) (int)
usb_device.linux.sysfs_path = '/sys/devices/pci0000:00/0000:00:1a.7/usb1' (string)
usb_device.max_power = 0 (0x0) (int)
usb_device.num_configurations = 1 (0x1) (int)
usb_device.num_interfaces = 1 (0x1) (int)
usb_device.num_ports = 6 (0x6) (int)
usb_device.product = '2.0 root hub' (string)
usb_device.product_id = 2 (0x2) (int)
usb_device.serial = '0000:00:1a.7' (string)
usb_device.speed = 480.0 (480) (double)
usb_device.vendor = 'Linux Foundation' (string)
usb_device.vendor_id = 7531 (0x1d6b) (int)
usb_device.version = 2.0 (2) (double)
udi = '/org/freedesktop/Hal/devices/usb_device_1d6b_2_0000_00_1a_7_if0'
info.linux.driver = 'hub' (string)
info.parent = '/org/freedesktop/Hal/devices/usb_device_1d6b_2_0000_00_1a_7' (string)
info.product = 'USB Hub Interface' (string)
info.subsystem = 'usb' (string)
info.udi = '/org/freedesktop/Hal/devices/usb_device_1d6b_2_0000_00_1a_7_if0' (string)
linux.hotplug_type = 2 (0x2) (int)
linux.subsystem = 'usb' (string)
linux.sysfs_path = '/sys/devices/pci0000:00/0000:00:1a.7/usb1/1-0:1.0' (string)
usb.bus_number = 1 (0x1) (int)
usb.can_wake_up = true (bool)
usb.configuration_value = 1 (0x1) (int)
usb.device_class = 9 (0x9) (int)
usb.device_protocol = 0 (0x0) (int)
usb.device_revision_bcd = 518 (0x206) (int)
usb.device_subclass = 0 (0x0) (int)
usb.interface.class = 9 (0x9) (int)
usb.interface.number = 0 (0x0) (int)
usb.interface.protocol = 0 (0x0) (int)
usb.interface.subclass = 0 (0x0) (int)
usb.is_self_powered = true (bool)
usb.linux.device_number = 1 (0x1) (int)
usb.linux.sysfs_path = '/sys/devices/pci0000:00/0000:00:1a.7/usb1/1-0:1.0' (string)
usb.max_power = 0 (0x0) (int)
usb.num_configurations = 1 (0x1) (int)
usb.num_interfaces = 1 (0x1) (int)
usb.num_ports = 6 (0x6) (int)
usb.product = 'USB Hub Interface' (string)
usb.product_id = 2 (0x2) (int)
usb.serial = '0000:00:1a.7' (string)
usb.speed = 480.0 (480) (double)
usb.vendor = 'Linux Foundation' (string)
usb.vendor_id = 7531 (0x1d6b) (int)
usb.version = 2.0 (2) (double)
udi = '/org/freedesktop/Hal/devices/pci_8086_2939'
info.linux.driver = 'uhci_hcd' (string)
info.parent = '/org/freedesktop/Hal/devices/computer' (string)
info.product = '82801I (ICH9 Family) USB UHCI Controller #6' (string)
info.subsystem = 'pci' (string)
info.udi = '/org/freedesktop/Hal/devices/pci_8086_2939' (string)
info.vendor = 'Intel Corporation' (string)
linux.hotplug_type = 2 (0x2) (int)
linux.subsystem = 'pci' (string)
linux.sysfs_path = '/sys/devices/pci0000:00/0000:00:1a.2' (string)
pci.device_class = 12 (0xc) (int)
pci.device_protocol = 0 (0x0) (int)
pci.device_subclass = 3 (0x3) (int)
pci.linux.sysfs_path = '/sys/devices/pci0000:00/0000:00:1a.2' (string)
pci.product = '82801I (ICH9 Family) USB UHCI Controller #6' (string)
pci.product_id = 10553 (0x2939) (int)
pci.subsys_product_id = 700 (0x2bc) (int)
pci.subsys_vendor = 'Dell' (string)
pci.subsys_vendor_id = 4136 (0x1028) (int)
pci.vendor = 'Intel Corporation' (string)
pci.vendor_id = 32902 (0x8086) (int)
udi = '/org/freedesktop/Hal/devices/usb_device_1d6b_1_0000_00_1a_2'
info.linux.driver = 'usb' (string)
info.parent = '/org/freedesktop/Hal/devices/pci_8086_2939' (string)
info.product = '1.1 root hub' (string)
info.subsystem = 'usb_device' (string)
info.udi = '/org/freedesktop/Hal/devices/usb_device_1d6b_1_0000_00_1a_2' (string)
info.vendor = 'Linux Foundation' (string)
linux.device_file = '/dev/bus/usb/005/001' (string)
linux.hotplug_type = 2 (0x2) (int)
linux.subsystem = 'usb' (string)
linux.sysfs_path = '/sys/devices/pci0000:00/0000:00:1a.2/usb5' (string)
usb_device.bus_number = 5 (0x5) (int)
usb_device.can_wake_up = true (bool)
usb_device.configuration_value = 1 (0x1) (int)
usb_device.device_class = 9 (0x9) (int)
usb_device.device_protocol = 0 (0x0) (int)
usb_device.device_revision_bcd = 518 (0x206) (int)
usb_device.device_subclass = 0 (0x0) (int)
usb_device.is_self_powered = true (bool)
usb_device.linux.device_number = 1 (0x1) (int)
usb_device.linux.sysfs_path = '/sys/devices/pci0000:00/0000:00:1a.2/usb5' (string)
usb_device.max_power = 0 (0x0) (int)
usb_device.num_configurations = 1 (0x1) (int)
usb_device.num_interfaces = 1 (0x1) (int)
usb_device.num_ports = 2 (0x2) (int)
usb_device.product = '1.1 root hub' (string)
usb_device.product_id = 1 (0x1) (int)
usb_device.serial = '0000:00:1a.2' (string)
usb_device.speed = 12.0 (12) (double)
usb_device.vendor = 'Linux Foundation' (string)
usb_device.vendor_id = 7531 (0x1d6b) (int)
usb_device.version = 1.1 (1.1) (double)
udi = '/org/freedesktop/Hal/devices/usb_device_1d6b_1_0000_00_1a_2_if0'
info.linux.driver = 'hub' (string)
info.parent = '/org/freedesktop/Hal/devices/usb_device_1d6b_1_0000_00_1a_2' (string)
info.product = 'USB Hub Interface' (string)
info.subsystem = 'usb' (string)
info.udi = '/org/freedesktop/Hal/devices/usb_device_1d6b_1_0000_00_1a_2_if0' (string)
linux.hotplug_type = 2 (0x2) (int)
linux.subsystem = 'usb' (string)
linux.sysfs_path = '/sys/devices/pci0000:00/0000:00:1a.2/usb5/5-0:1.0' (string)
usb.bus_number = 5 (0x5) (int)
usb.can_wake_up = true (bool)
usb.configuration_value = 1 (0x1) (int)
usb.device_class = 9 (0x9) (int)
usb.device_protocol = 0 (0x0) (int)
usb.device_revision_bcd = 518 (0x206) (int)
usb.device_subclass = 0 (0x0) (int)
usb.interface.class = 9 (0x9) (int)
usb.interface.number = 0 (0x0) (int)
usb.interface.protocol = 0 (0x0) (int)
usb.interface.subclass = 0 (0x0) (int)
usb.is_self_powered = true (bool)
usb.linux.device_number = 1 (0x1) (int)
usb.linux.sysfs_path = '/sys/devices/pci0000:00/0000:00:1a.2/usb5/5-0:1.0' (string)
usb.max_power = 0 (0x0) (int)
usb.num_configurations = 1 (0x1) (int)
usb.num_interfaces = 1 (0x1) (int)
usb.num_ports = 2 (0x2) (int)
usb.product = 'USB Hub Interface' (string)
usb.product_id = 1 (0x1) (int)
usb.serial = '0000:00:1a.2' (string)
usb.speed = 12.0 (12) (double)
usb.vendor = 'Linux Foundation' (string)
usb.vendor_id = 7531 (0x1d6b) (int)
usb.version = 1.1 (1.1) (double)
udi = '/org/freedesktop/Hal/devices/pci_8086_2938'
info.linux.driver = 'uhci_hcd' (string)
info.parent = '/org/freedesktop/Hal/devices/computer' (string)
info.product = '82801I (ICH9 Family) USB UHCI Controller #5' (string)
info.subsystem = 'pci' (string)
info.udi = '/org/freedesktop/Hal/devices/pci_8086_2938' (string)
info.vendor = 'Intel Corporation' (string)
linux.hotplug_type = 2 (0x2) (int)
linux.subsystem = 'pci' (string)
linux.sysfs_path = '/sys/devices/pci0000:00/0000:00:1a.1' (string)
pci.device_class = 12 (0xc) (int)
pci.device_protocol = 0 (0x0) (int)
pci.device_subclass = 3 (0x3) (int)
pci.linux.sysfs_path = '/sys/devices/pci0000:00/0000:00:1a.1' (string)
pci.product = '82801I (ICH9 Family) USB UHCI Controller #5' (string)
pci.product_id = 10552 (0x2938) (int)
pci.subsys_product_id = 700 (0x2bc) (int)
pci.subsys_vendor = 'Dell' (string)
pci.subsys_vendor_id = 4136 (0x1028) (int)
pci.vendor = 'Intel Corporation' (string)
pci.vendor_id = 32902 (0x8086) (int)
udi = '/org/freedesktop/Hal/devices/usb_device_1d6b_1_0000_00_1a_1'
info.linux.driver = 'usb' (string)
info.parent = '/org/freedesktop/Hal/devices/pci_8086_2938' (string)
info.product = '1.1 root hub' (string)
info.subsystem = 'usb_device' (string)
info.udi = '/org/freedesktop/Hal/devices/usb_device_1d6b_1_0000_00_1a_1' (string)
info.vendor = 'Linux Foundation' (string)
linux.device_file = '/dev/bus/usb/004/001' (string)
linux.hotplug_type = 2 (0x2) (int)
linux.subsystem = 'usb' (string)
linux.sysfs_path = '/sys/devices/pci0000:00/0000:00:1a.1/usb4' (string)
usb_device.bus_number = 4 (0x4) (int)
usb_device.can_wake_up = true (bool)
usb_device.configuration_value = 1 (0x1) (int)
usb_device.device_class = 9 (0x9) (int)
usb_device.device_protocol = 0 (0x0) (int)
usb_device.device_revision_bcd = 518 (0x206) (int)
usb_device.device_subclass = 0 (0x0) (int)
usb_device.is_self_powered = true (bool)
usb_device.linux.device_number = 1 (0x1) (int)
usb_device.linux.sysfs_path = '/sys/devices/pci0000:00/0000:00:1a.1/usb4' (string)
usb_device.max_power = 0 (0x0) (int)
usb_device.num_configurations = 1 (0x1) (int)
usb_device.num_interfaces = 1 (0x1) (int)
usb_device.num_ports = 2 (0x2) (int)
usb_device.product = '1.1 root hub' (string)
usb_device.product_id = 1 (0x1) (int)
usb_device.serial = '0000:00:1a.1' (string)
usb_device.speed = 12.0 (12) (double)
usb_device.vendor = 'Linux Foundation' (string)
usb_device.vendor_id = 7531 (0x1d6b) (int)
usb_device.version = 1.1 (1.1) (double)
udi = '/org/freedesktop/Hal/devices/usb_device_1d6b_1_0000_00_1a_1_if0'
info.linux.driver = 'hub' (string)
info.parent = '/org/freedesktop/Hal/devices/usb_device_1d6b_1_0000_00_1a_1' (string)
info.product = 'USB Hub Interface' (string)
info.subsystem = 'usb' (string)
info.udi = '/org/freedesktop/Hal/devices/usb_device_1d6b_1_0000_00_1a_1_if0' (string)
linux.hotplug_type = 2 (0x2) (int)
linux.subsystem = 'usb' (string)
linux.sysfs_path = '/sys/devices/pci0000:00/0000:00:1a.1/usb4/4-0:1.0' (string)
usb.bus_number = 4 (0x4) (int)
usb.can_wake_up = true (bool)
usb.configuration_value = 1 (0x1) (int)
usb.device_class = 9 (0x9) (int)
usb.device_protocol = 0 (0x0) (int)
usb.device_revision_bcd = 518 (0x206) (int)
usb.device_subclass = 0 (0x0) (int)
usb.interface.class = 9 (0x9) (int)
usb.interface.number = 0 (0x0) (int)
usb.interface.protocol = 0 (0x0) (int)
usb.interface.subclass = 0 (0x0) (int)
usb.is_self_powered = true (bool)
usb.linux.device_number = 1 (0x1) (int)
usb.linux.sysfs_path = '/sys/devices/pci0000:00/0000:00:1a.1/usb4/4-0:1.0' (string)
usb.max_power = 0 (0x0) (int)
usb.num_configurations = 1 (0x1) (int)
usb.num_interfaces = 1 (0x1) (int)
usb.num_ports = 2 (0x2) (int)
usb.product = 'USB Hub Interface' (string)
usb.product_id = 1 (0x1) (int)
usb.serial = '0000:00:1a.1' (string)
usb.speed = 12.0 (12) (double)
usb.vendor = 'Linux Foundation' (string)
usb.vendor_id = 7531 (0x1d6b) (int)
usb.version = 1.1 (1.1) (double)
udi = '/org/freedesktop/Hal/devices/pci_8086_2937'
info.linux.driver = 'uhci_hcd' (string)
info.parent = '/org/freedesktop/Hal/devices/computer' (string)
info.product = '82801I (ICH9 Family) USB UHCI Controller #4' (string)
info.subsystem = 'pci' (string)
info.udi = '/org/freedesktop/Hal/devices/pci_8086_2937' (string)
info.vendor = 'Intel Corporation' (string)
linux.hotplug_type = 2 (0x2) (int)
linux.subsystem = 'pci' (string)
linux.sysfs_path = '/sys/devices/pci0000:00/0000:00:1a.0' (string)
pci.device_class = 12 (0xc) (int)
pci.device_protocol = 0 (0x0) (int)
pci.device_subclass = 3 (0x3) (int)
pci.linux.sysfs_path = '/sys/devices/pci0000:00/0000:00:1a.0' (string)
pci.product = '82801I (ICH9 Family) USB UHCI Controller #4' (string)
pci.product_id = 10551 (0x2937) (int)
pci.subsys_product_id = 700 (0x2bc) (int)
pci.subsys_vendor = 'Dell' (string)
pci.subsys_vendor_id = 4136 (0x1028) (int)
pci.vendor = 'Intel Corporation' (string)
pci.vendor_id = 32902 (0x8086) (int)
udi = '/org/freedesktop/Hal/devices/usb_device_1d6b_1_0000_00_1a_0'
info.linux.driver = 'usb' (string)
info.parent = '/org/freedesktop/Hal/devices/pci_8086_2937' (string)
info.product = '1.1 root hub' (string)
info.subsystem = 'usb_device' (string)
info.udi = '/org/freedesktop/Hal/devices/usb_device_1d6b_1_0000_00_1a_0' (string)
info.vendor = 'Linux Foundation' (string)
linux.device_file = '/dev/bus/usb/003/001' (string)
linux.hotplug_type = 2 (0x2) (int)
linux.subsystem = 'usb' (string)
linux.sysfs_path = '/sys/devices/pci0000:00/0000:00:1a.0/usb3' (string)
usb_device.bus_number = 3 (0x3) (int)
usb_device.can_wake_up = true (bool)
usb_device.configuration_value = 1 (0x1) (int)
usb_device.device_class = 9 (0x9) (int)
usb_device.device_protocol = 0 (0x0) (int)
usb_device.device_revision_bcd = 518 (0x206) (int)
usb_device.device_subclass = 0 (0x0) (int)
usb_device.is_self_powered = true (bool)
usb_device.linux.device_number = 1 (0x1) (int)
usb_device.linux.sysfs_path = '/sys/devices/pci0000:00/0000:00:1a.0/usb3' (string)
usb_device.max_power = 0 (0x0) (int)
usb_device.num_configurations = 1 (0x1) (int)
usb_device.num_interfaces = 1 (0x1) (int)
usb_device.num_ports = 2 (0x2) (int)
usb_device.product = '1.1 root hub' (string)
usb_device.product_id = 1 (0x1) (int)
usb_device.serial = '0000:00:1a.0' (string)
usb_device.speed = 12.0 (12) (double)
usb_device.vendor = 'Linux Foundation' (string)
usb_device.vendor_id = 7531 (0x1d6b) (int)
usb_device.version = 1.1 (1.1) (double)
udi = '/org/freedesktop/Hal/devices/usb_device_1d6b_1_0000_00_1a_0_if0'
info.linux.driver = 'hub' (string)
info.parent = '/org/freedesktop/Hal/devices/usb_device_1d6b_1_0000_00_1a_0' (string)
info.product = 'USB Hub Interface' (string)
info.subsystem = 'usb' (string)
info.udi = '/org/freedesktop/Hal/devices/usb_device_1d6b_1_0000_00_1a_0_if0' (string)
linux.hotplug_type = 2 (0x2) (int)
linux.subsystem = 'usb' (string)
linux.sysfs_path = '/sys/devices/pci0000:00/0000:00:1a.0/usb3/3-0:1.0' (string)
usb.bus_number = 3 (0x3) (int)
usb.can_wake_up = true (bool)
usb.configuration_value = 1 (0x1) (int)
usb.device_class = 9 (0x9) (int)
usb.device_protocol = 0 (0x0) (int)
usb.device_revision_bcd = 518 (0x206) (int)
usb.device_subclass = 0 (0x0) (int)
usb.interface.class = 9 (0x9) (int)
usb.interface.number = 0 (0x0) (int)
usb.interface.protocol = 0 (0x0) (int)
usb.interface.subclass = 0 (0x0) (int)
usb.is_self_powered = true (bool)
usb.linux.device_number = 1 (0x1) (int)
usb.linux.sysfs_path = '/sys/devices/pci0000:00/0000:00:1a.0/usb3/3-0:1.0' (string)
usb.max_power = 0 (0x0) (int)
usb.num_configurations = 1 (0x1) (int)
usb.num_interfaces = 1 (0x1) (int)
usb.num_ports = 2 (0x2) (int)
usb.product = 'USB Hub Interface' (string)
usb.product_id = 1 (0x1) (int)
usb.serial = '0000:00:1a.0' (string)
usb.speed = 12.0 (12) (double)
usb.vendor = 'Linux Foundation' (string)
usb.vendor_id = 7531 (0x1d6b) (int)
usb.version = 1.1 (1.1) (double)
udi = '/org/freedesktop/Hal/devices/pci_8086_2a43'
info.parent = '/org/freedesktop/Hal/devices/computer' (string)
info.product = 'Mobile 4 Series Chipset Integrated Graphics Controller' (string)
info.subsystem = 'pci' (string)
info.udi = '/org/freedesktop/Hal/devices/pci_8086_2a43' (string)
info.vendor = 'Intel Corporation' (string)
linux.hotplug_type = 2 (0x2) (int)
linux.subsystem = 'pci' (string)
linux.sysfs_path = '/sys/devices/pci0000:00/0000:00:02.1' (string)
pci.device_class = 3 (0x3) (int)
pci.device_protocol = 0 (0x0) (int)
pci.device_subclass = 128 (0x80) (int)
pci.linux.sysfs_path = '/sys/devices/pci0000:00/0000:00:02.1' (string)
pci.product = 'Mobile 4 Series Chipset Integrated Graphics Controller' (string)
pci.product_id = 10819 (0x2a43) (int)
pci.subsys_product_id = 700 (0x2bc) (int)
pci.subsys_vendor = 'Dell' (string)
pci.subsys_vendor_id = 4136 (0x1028) (int)
pci.vendor = 'Intel Corporation' (string)
pci.vendor_id = 32902 (0x8086) (int)
udi = '/org/freedesktop/Hal/devices/pci_8086_2a42'
info.parent = '/org/freedesktop/Hal/devices/computer' (string)
info.product = 'Mobile 4 Series Chipset Integrated Graphics Controller' (string)
info.subsystem = 'pci' (string)
info.udi = '/org/freedesktop/Hal/devices/pci_8086_2a42' (string)
info.vendor = 'Intel Corporation' (string)
linux.hotplug_type = 2 (0x2) (int)
linux.subsystem = 'pci' (string)
linux.sysfs_path = '/sys/devices/pci0000:00/0000:00:02.0' (string)
pci.device_class = 3 (0x3) (int)
pci.device_protocol = 0 (0x0) (int)
pci.device_subclass = 0 (0x0) (int)
pci.linux.sysfs_path = '/sys/devices/pci0000:00/0000:00:02.0' (string)
pci.product = 'Mobile 4 Series Chipset Integrated Graphics Controller' (string)
pci.product_id = 10818 (0x2a42) (int)
pci.subsys_product_id = 700 (0x2bc) (int)
pci.subsys_vendor = 'Dell' (string)
pci.subsys_vendor_id = 4136 (0x1028) (int)
pci.vendor = 'Intel Corporation' (string)
pci.vendor_id = 32902 (0x8086) (int)
udi = '/org/freedesktop/Hal/devices/pci_8086_2a42_drm_i915_card0'
access_control.file = '/dev/dri/card0' (string)
access_control.type = 'video' (string)
drm.dri_library = 'i915' (string)
info.callouts.add = {'hal-acl-tool --add-device'} (string list)
info.callouts.remove = {'hal-acl-tool --remove-device'} (string list)
info.capabilities = {'drm', 'access_control'} (string list)
info.category = 'drm' (string)
info.parent = '/org/freedesktop/Hal/devices/pci_8086_2a42' (string)
info.product = 'Direct Rendering Manager Device' (string)
info.subsystem = 'drm' (string)
info.udi = '/org/freedesktop/Hal/devices/pci_8086_2a42_drm_i915_card0' (string)
info.vendor = 'Intel Corporation' (string)
linux.device_file = '/dev/dri/card0' (string)
linux.hotplug_type = 2 (0x2) (int)
linux.subsystem = 'drm' (string)
linux.sysfs_path = '/sys/devices/pci0000:00/0000:00:02.0/drm/card0' (string)
udi = '/org/freedesktop/Hal/devices/pci_8086_2a40'
info.linux.driver = 'agpgart-intel' (string)
info.parent = '/org/freedesktop/Hal/devices/computer' (string)
info.product = 'Mobile 4 Series Chipset Memory Controller Hub' (string)
info.subsystem = 'pci' (string)
info.udi = '/org/freedesktop/Hal/devices/pci_8086_2a40' (string)
info.vendor = 'Intel Corporation' (string)
linux.hotplug_type = 2 (0x2) (int)
linux.subsystem = 'pci' (string)
linux.sysfs_path = '/sys/devices/pci0000:00/0000:00:00.0' (string)
pci.device_class = 6 (0x6) (int)
pci.device_protocol = 0 (0x0) (int)
pci.device_subclass = 0 (0x0) (int)
pci.linux.sysfs_path = '/sys/devices/pci0000:00/0000:00:00.0' (string)
pci.product = 'Mobile 4 Series Chipset Memory Controller Hub' (string)
pci.product_id = 10816 (0x2a40) (int)
pci.subsys_product_id = 700 (0x2bc) (int)
pci.subsys_vendor = 'Dell' (string)
pci.subsys_vendor_id = 4136 (0x1028) (int)
pci.vendor = 'Intel Corporation' (string)
pci.vendor_id = 32902 (0x8086) (int)
udi = '/org/freedesktop/Hal/devices/fuse'
access_control.file = '/dev/fuse' (string)
access_control.type = 'camera' (string)
info.callouts.add = {'hal-acl-tool --add-device'} (string list)
info.callouts.remove = {'hal-acl-tool --remove-device'} (string list)
info.capabilities = {'access_control'} (string list)
info.parent = '/org/freedesktop/Hal/devices/pci_8086_2a40' (string)
info.subsystem = 'unknown' (string)
info.udi = '/org/freedesktop/Hal/devices/fuse' (string)
Dumped 123 device(s) from the Global Device List.
------------------------------------------------
-------------- next part --------------
A non-text attachment was scrubbed...
Name: nm-ignore-killswitches.patch
Type: text/x-patch
Size: 1205 bytes
Desc: not available
URL: <http://lists.alioth.debian.org/pipermail/pkg-utopia-maintainers/attachments/20090830/0c27b9be/attachment-0001.bin>
-------------- next part --------------
A non-text attachment was scrubbed...
Name: not available
Type: application/pgp-signature
Size: 197 bytes
Desc: This is a digitally signed message part
URL: <http://lists.alioth.debian.org/pipermail/pkg-utopia-maintainers/attachments/20090830/0c27b9be/attachment-0001.pgp>
More information about the Pkg-utopia-maintainers
mailing list