[Pkg-utopia-maintainers] Bug#933216: network-manager: system refuse to work with Intel i210 interface, only work with i217-V. can only use 1 eth conn.

[Mélanie Legault]

Package: network-manager
Version: 1.14.6-2
Severity: important



-- System Information:
Debian Release: 10.0
  APT prefers stable
  APT policy: (500, 'stable')
Architecture: amd64 (x86_64)

Kernel: Linux 4.19.0-5-amd64 (SMP w/8 CPU cores)
Locale: LANG=en_CA.UTF-8, LC_CTYPE=en_CA.UTF-8 (charmap=UTF-8), LANGUAGE=en_CA:en (charmap=UTF-8)
Shell: /bin/sh linked to /usr/bin/dash
Init: systemd (via /run/systemd/system)
LSM: AppArmor: enabled

Versions of packages network-manager depends on:
ii  adduser                3.118
ii  dbus                   1.12.16-1
ii  init-system-helpers    1.56+nmu1
ii  libaudit1              1:2.8.4-3
ii  libbluetooth3          5.50-1
ii  libc6                  2.28-10
ii  libcurl3-gnutls        7.64.0-4
ii  libglib2.0-0           2.58.3-2
ii  libgnutls30            3.6.7-4
ii  libjansson4            2.12-1
ii  libmm-glib0            1.10.0-1
ii  libndp0                1.6-1+b1
ii  libnewt0.52            0.52.20-8
ii  libnm0                 1.14.6-2
ii  libpam-systemd         241-5
ii  libpolkit-agent-1-0    0.105-25
ii  libpolkit-gobject-1-0  0.105-25
ii  libpsl5                0.20.2-2
ii  libreadline7           7.0-5
ii  libselinux1            2.8-1+b1
ii  libsystemd0            241-5
ii  libteamdctl0           1.28-1
ii  libudev1               241-5
ii  libuuid1               2.33.1-0.1
ii  lsb-base               10.2019051400
ii  policykit-1            0.105-25
ii  udev                   241-5
ii  wpasupplicant          2:2.7+git20190128+0c1e29f-6

Versions of packages network-manager recommends:
ii  crda                         3.18-1
ii  dnsmasq-base [dnsmasq-base]  2.80-1
ii  iptables                     1.8.2-4
ii  isc-dhcp-client              4.4.1-2
ii  modemmanager                 1.10.0-1
ii  ppp                          2.4.7-2+4.1

Versions of packages network-manager suggests:
pn  libteam-utils  <none>

- i210 interface do not show up in network-manager gui
- trying to configure by hand with networking associate i210 config with
  i217-V physical port

lshw -class network
  *-network DISABLED        
       description: Ethernet interface
       product: Ethernet Connection I217-V
       vendor: Intel Corporation
       physical id: 19
       bus info: pci at 0000:00:19.0
       logical name: eno1
       version: 04
       serial: 94:de:80:6e:ce:05
       capacity: 1Gbit/s
       width: 32 bits
       clock: 33MHz
       capabilities: pm msi bus_master cap_list ethernet physical tp 10bt 10bt-fd 100bt 100bt-fd 1000bt-fd autonegotiation
       configuration: autonegotiation=on broadcast=yes driver=e1000e driverversion=3.2.6-k firmware=0.13-4 latency=0 link=no multicast=yes port=twisted pair
       resources: irq:29 memory:f0900000-f091ffff memory:f093d000-f093dfff ioport:f080(size=32)
  *-network
       description: Ethernet interface
       product: I210 Gigabit Network Connection
       vendor: Intel Corporation
       physical id: 0
       bus info: pci at 0000:02:00.0
       logical name: enp2s0
       version: 03
       serial: 94:de:80:6e:ce:15
       size: 1Gbit/s
       capacity: 1Gbit/s
       width: 32 bits
       clock: 33MHz
       capabilities: pm msi msix pciexpress bus_master cap_list rom ethernet physical tp 10bt 10bt-fd 100bt 100bt-fd 1000bt-fd autonegotiation
       configuration: autonegotiation=on broadcast=yes driver=igb driverversion=5.4.0-k duplex=full firmware=3.11, 0x80000469 ip=192.168.6.141 latency=0 link=yes multicast=yes port=twisted pair speed=1Gbit/s
       resources: irq:19 memory:f0500000-f05fffff ioport:e000(size=32) memory:f0600000-f0603fff memory:f0400000-f04fffff

-after restarting networking:
eno1: flags=4098<BROADCAST,MULTICAST>  mtu 1500
        ether 94:de:80:6e:ce:05  txqueuelen 1000  (Ethernet)
        RX packets 0  bytes 0 (0.0 B)
        RX errors 0  dropped 0  overruns 0  frame 0
        TX packets 0  bytes 0 (0.0 B)
        TX errors 0  dropped 0 overruns 0  carrier 0  collisions 0
        device interrupt 20  memory 0xf0900000-f0920000  

enp2s0: flags=4163<UP,BROADCAST,RUNNING,MULTICAST>  mtu 1500
        inet 192.168.6.141  netmask 255.255.255.0  broadcast 192.168.6.255
        inet6 fe80::96de:80ff:fe6e:ce15  prefixlen 64  scopeid 0x20<link>
        inet6 fd36:af4:e180:0:96de:80ff:fe6e:ce15  prefixlen 64  scopeid 0x0<global>
        ether 94:de:80:6e:ce:15  txqueuelen 1000  (Ethernet)
        RX packets 3212  bytes 2575581 (2.4 MiB)
        RX errors 0  dropped 0  overruns 0  frame 0
        TX packets 2675  bytes 331996 (324.2 KiB)
        TX errors 0  dropped 0 overruns 0  carrier 0  collisions 0
        device memory 0xf0500000-f05fffff  

lo: flags=73<UP,LOOPBACK,RUNNING>  mtu 65536
        inet 127.0.0.1  netmask 255.0.0.0
        inet6 ::1  prefixlen 128  scopeid 0x10<host>
        loop  txqueuelen 1000  (Local Loopback)
        RX packets 311  bytes 28247 (27.5 KiB)
        RX errors 0  dropped 0  overruns 0  frame 0
        TX packets 311  bytes 28247 (27.5 KiB)
        TX errors 0  dropped 0 overruns 0  carrier 0  collisions 0

- but traffic is not going on enp2s0 physical interface but eno1 physical interface.

- even tried to connect both physical interface to the same subnet, and traffic was only going thru i217-V physical, refused to go thru i210 even if route existed for both. when disconnecting cable to i217-V, no connection at all.

-- no debconf information