[sane-devel] UMAX Astra 610S (better specs)
redhat at emphanet.com
redhat at emphanet.com
Thu Nov 15 08:27:52 GMT 2001
Hi again.
ok.. my last posting about the 610S was long and .. well.. tiresome.. here's
the details to end that.
I'm running RH 7.2, Kernel 2.4.9-13, using a BusLogic SCSI host BT-930 (SCSI-2
50HD).
The chain on this bus is as follows:
HP-9600E BURNER -> Castlewood ORB (removable 2.2GB disk drive) -> UMAX Astra
610S scanner.
>From Host card: 50HD -> BURNER -> 50HD -> ORB -> 50HD/25DB -> SCANNER.
SCSI card module BusLogic.o
Sane-Backend 1.0.6
Xsane frontend 0.80
Problems are:
Can't scan over 105 dpi in Color mode, but can scan 300 dpi in LineArt.
If attempting to scan over 105 dpi in color mode, it starts the scan and returns
with apx 1" or less of a graphic. When in color mode, 105 dpi or less, the scan
completes the whole scan. Check this out. If I use the PREVIEW part of Xsane
and crop a section of the scan, the scanner moves to the start of that cropped
area, begins to scan and returns with that 1" or less blip of an image. I get
no errors, that I know of. Correct me if I'm wrong, but I think it's only
scanning one line and aborts, or gets a complete signal. I don't know. Here is
some information:
/proc/scsi/scsi ------------------------------------------------------
Attached devices:
Host: scsi0 Channel: 00 Id: 01 Lun: 00
Vendor: UMAX Model: Astra 610S Rev: V1.3
Type: Scanner ANSI SCSI revision: 02
Host: scsi0 Channel: 00 Id: 04 Lun: 00
Vendor: HP Model: CD-Writer+ 9600 Rev: 1.0a
Type: CD-ROM ANSI SCSI revision: 04
Host: scsi0 Channel: 00 Id: 06 Lun: 00
Vendor: CWS ORB2 Model: -SE U ID 6 Rev: D20
Type: Direct-Access ANSI SCSI revision: 02
----------------------------------------------------------------------
cat /proc/scsi/sg/* --------------------------------------------------
0
dev_max(currently)=9 max_active_device=3 (origin 1)
scsi_dma_free_sectors=112 sg_pool_secs_aval=320 def_reserved_size=32768
32768
host
chan
id
lun
type
opens
qdepth
busy
online
0
0
1
0
6
0
3
0
1
0
0
4
0
5
0
3
0
1
0
0
6
0
0
0
3
0
1
UMAX Astra 610S V1.3
HP CD-Writer+ 9600 1.0a
CWS ORB2 -SE U ID 6 D20
uid
busy
cpl
scatg
isa
emul
54272
0
3
128
0
0
0
0
12
64
0
1
BusLogic BT-930
iSCSI (2.0.1.8)
30120
Version: 3.1.20 (20010814)
----------------------------------------------------------------------------
cat /proc/scsi/BusLogic/0 --------------------------------------------------
***** BusLogic SCSI Driver Version 2.1.15 of 17 August 1998 *****
Copyright 1995-1998 by Leonard N. Zubkoff <lnz at dandelion.com>
Configuring BusLogic Model BT-930 PCI Ultra SCSI Host Adapter
Firmware Version: 5.02, I/O Address: 0xD400, IRQ Channel: 9/Level
PCI Bus: 0, Device: 9, Address: 0xDB000000, Host Adapter SCSI ID: 7
Parity Checking: Disabled, Extended Translation: Enabled
Synchronous Negotiation: FFFFFSF#, Wide Negotiation: Disabled
Disconnect/Reconnect: Enabled, Tagged Queuing: Enabled
Driver Queue Depth: 255, Scatter/Gather Limit: 128 segments
Tagged Queue Depth: Automatic, Untagged Queue Depth: 3
Error Recovery Strategy: Default, SCSI Bus Reset: Enabled
SCSI Bus Termination: Enabled, SCAM: Disabled
*** BusLogic BT-930 Initialized Successfully ***
Target 1: Queue Depth 3, Asynchronous
Target 4: Queue Depth 3, Synchronous at 10.0 MB/sec, offset 15
Target 6: Queue Depth 3, Synchronous at 10.0 MB/sec, offset 15
Current Driver Queue Depth: 255
Currently Allocated CCBs: 28
DATA TRANSFER STATISTICS
Target
Tagged Queuing Queue Depth Active Attempted Completed
======
==============
=========== ====== ========= =========
1 Not Supported 3 0 1 1
4 Not Supported 3 0 1060 1060
6 Not Supported 3 0 6 6
Target Read Commands Write Commands Total Bytes Read Total Bytes Written
====== ============= ============== =================== ===================
1 0 0 0 0
4 0 0 0 0
6 1 0 1024 0
Target Command 0-1KB 1-2KB 2-4KB 4-8KB 8-16KB
====== ======= ========= ========= ========= ========= =========
1 Read 0 0 0 0 0
1 Write 0 0 0 0 0
4 Read 0 0 0 0 0
4 Write 0 0 0 0 0
6 Read 0 1 0 0 0
6 Write 0 0 0 0 0
Target Command 16-32KB 32-64KB 64-128KB 128-256KB 256KB+
====== ======= ========= ========= ========= ========= =========
1 Read 0 0 0 0 0
1 Write 0 0 0 0 0
4 Read 0 0 0 0 0
4 Write 0 0 0 0 0
6 Read 0 0 0 0 0
6 Write 0 0 0 0 0
ERROR RECOVERY STATISTICS
Command Aborts Bus Device Resets Host Adapter Resets
Target
Requested Completed Requested Completed Requested Completed
ID \\\\ Attempted //// \\\\ Attempted //// \\\\ Attempted ////
======
===== ===== ===== ===== ===== ===== ===== ===== =====
1 0 0 0 0 0 0 0 0 0
4 0 0 0 0 0 0 0 0 0
6 0 0 0 0 0 0 0 0 0
External Host Adapter Resets: 0
Host Adapter Internal Errors: 0
-----------------------------------------------------------------------------
cat /etc/sane.d/dll.conf ----------------------------------------------------
# enable the next line if you want to allow access through the network:
#net
#abaton
#agfafocus
#apple
#avision
#artec
#as6e
#bh
#canon
#coolscan
#dc25
#dc210
#dc240
#dmc
#epson
#hp
#m3096g
#microtek
#microtek2
#mustek
#mustek_pp
#nec
#pie
#pint
#plustek
#pnm
#qcam
#ricoh
#s9036
#sharp
#sm3600
#snapscan
#sp15c
#tamarackumax
#umax_pp
#v4l
-------------------------------------------------------------------------------
cat /etc/sane.d/umax.conf -----------------------------------------------------
#
# Options for the umax backend
#option scsi-maxqueue 2
#option scsi-buffer-size-min 65536
#option scsi-buffer-size-max 262144
#option scan-lines 100
#option preview-lines 20
#option handle-bad-sense-error 0
#option execute-request-sense 0
#option force-preview-bit-rgb 0
#option lamp-control-available 0
#
# linux device identification:
#scsi vendor model type bus channel id lun
scsi UMAX * Scanner
#scsi LinoHell JADE
#scsi LinoHell Office
#scsi LinoHell Office2
#scsi LinoHell SAPHIR2
#scsi HDM LS4H1S
#scsi Nikon AX-210
#scsi KYE ColorPage-HR5
#scsi EPSON Perfection600
#scsi ESCORT "Galleria 600S"
#
# device list for non-linux-systems:
#/dev/scanner
-----------------------------------------------------------------------------
This is about all I can gather for the moment. I suppose the most information
is in the BusLogic Configuration. It's on IRQ 9 which is being shared with USB
host.
I'm stumped for now. Until later..
Jordan Peterson
More information about the sane-devel
mailing list