[sane-devel] Mustek 1200UB: Strange Scanner problems...
mdew
mdew at orcon.net.nz
Fri Apr 26 03:16:11 BST 2002
Anyone encountered something like this? (during a "preview") Ive had
problems scanning...and some rather loud noises coming from the
device,..yet in windows no sounds come from the scanner during a scan,
so it cant be a hardware fault.
Scanner: Mustek 1200UB (USB) Kernel Detected etc...
Sane: 1.0.7
Xsane: 0.86
Mustek Sane Backend: 1.0-14 (tried normal sane-backend too)
http://mdew.orcon.net.nz/debug-log.tar.gz
[mustek_usb] usb_low_read_reg: Reg: 0x1f, Value: 0x62
[mustek_usb] usb_low_get_home_sensor: exit
[mustek_usb] usb_low_get_home_sensor: start
[mustek_usb] usb_low_read_reg: Reg: 0x1f, Value: 0x62
[mustek_usb] usb_low_get_home_sensor: exit
[mustek_usb] usb_low_get_home_sensor: start
[mustek_usb] usb_low_read_reg: Reg: 0x1f, Value: 0x62
[mustek_usb] usb_low_get_home_sensor: exit
[mustek_usb] usb_low_get_home_sensor: start
[mustek_usb] usb_low_read_reg: Reg: 0x1f, Value: 0x62
[mustek_usb] usb_low_get_home_sensor: exit
[mustek_usb] usb_low_get_home_sensor: start
[mustek_usb] usb_low_read_reg: Reg: 0x1f, Value: 0x62
[mustek_usb] usb_low_get_home_sensor: exit
[mustek_usb] usb_low_get_home_sensor: start
[mustek_usb] usb_low_read_reg: Reg: 0x1f, Value: 0x62
[mustek_usb] usb_low_get_home_sensor: exit
[mustek_usb] usb_low_get_home_sensor: start
[mustek_usb] usb_low_read_reg: Reg: 0x1f, Value: 0x60
[mustek_usb] usb_low_get_home_sensor: exit
[mustek_usb] usb_low_get_home_sensor: start
[mustek_usb] usb_low_read_reg: Reg: 0x1f, Value: 0x60
[mustek_usb] usb_low_get_home_sensor: exit
[mustek_usb] usb_low_get_home_sensor: start
[mustek_usb] usb_low_read_reg: Reg: 0x1f, Value: 0x60
[mustek_usb] usb_low_get_home_sensor: exit
[mustek_usb] usb_low_get_home_sensor: start
[mustek_usb] usb_low_read_reg: Reg: 0x1f, Value: 0x60
[mustek_usb] usb_low_get_home_sensor: exit
[mustek_usb] usb_low_get_home_sensor: start
[mustek_usb] usb_low_read_reg: Reg: 0x1f, Value: 0x60
[mustek_usb] usb_low_get_home_sensor: exit
[mustek_usb] usb_low_get_home_sensor: start
[mustek_usb] usb_low_read_reg: Reg: 0x1f, Value: 0x60
[mustek_usb] usb_low_get_home_sensor: exit
[mustek_usb] usb_low_get_home_sensor: start
[mustek_usb] usb_low_read_reg: Reg: 0x1f, Value: 0x60
[mustek_usb] usb_low_get_home_sensor: exit
[mustek_usb] usb_low_get_home_sensor: start
[mustek_usb] usb_low_read_reg: Reg: 0x1f, Value: 0x60
[mustek_usb] usb_low_get_home_sensor: exit
[mustek_usb] usb_low_get_home_sensor: start
[mustek_usb] usb_low_read_reg: Reg: 0x1f, Value: 0x62
[mustek_usb] usb_low_get_home_sensor: exit
[mustek_usb] usb_low_get_home_sensor: start
[mustek_usb] usb_low_read_reg: Reg: 0x1f, Value: 0x62
[mustek_usb] usb_low_get_home_sensor: exit
[mustek_usb] usb_low_get_home_sensor: start
[mustek_usb] usb_low_read_reg: Reg: 0x1f, Value: 0x62
[mustek_usb] usb_low_get_home_sensor: exit
[mustek_usb] usb_low_get_home_sensor: start
[mustek_usb] usb_low_read_reg: Reg: 0x1f, Value: 0x62
[mustek_usb] usb_low_get_home_sensor: exit
[mustek_usb] usb_low_get_home_sensor: start
[mustek_usb] usb_low_read_reg: Reg: 0x1f, Value: 0x62
[mustek_usb] usb_low_get_home_sensor: exit
[mustek_usb] usb_low_get_home_sensor: start
[mustek_usb] usb_low_read_reg: Reg: 0x1f, Value: 0x62
[mustek_usb] usb_low_get_home_sensor: exit
[mustek_usb] usb_low_get_home_sensor: start
[mustek_usb] usb_low_read_reg: Reg: 0x1f, Value: 0x62
[mustek_usb] usb_low_get_home_sensor: exit
[mustek_usb] usb_low_get_home_sensor: start
[mustek_usb] usb_low_read_reg: Reg: 0x1f, Value: 0x62
[mustek_usb] usb_low_get_home_sensor: exit
[mustek_usb] usb_low_get_home_sensor: start
[mustek_usb] usb_low_read_reg: Reg: 0x1f, Value: 0x62
[mustek_usb] usb_low_get_home_sensor: exit
[mustek_usb] usb_low_get_home_sensor: start
[mustek_usb] usb_low_read_reg: Reg: 0x1f, Value: 0x62
[mustek_usb] usb_low_get_home_sensor: exit
[mustek_usb] usb_low_get_home_sensor: start
[mustek_usb] usb_low_read_reg: Reg: 0x1f, Value: 0x60
[mustek_usb] usb_low_get_home_sensor: exit
[mustek_usb] usb_low_get_home_sensor: start
[mustek_usb] usb_low_read_reg: Reg: 0x1f, Value: 0x60
[mustek_usb] usb_low_get_home_sensor: exit
[mustek_usb] usb_low_get_home_sensor: start
[mustek_usb] usb_low_read_reg: Reg: 0x1f, Value: 0x60
[mustek_usb] usb_low_get_home_sensor: exit
[mustek_usb] usb_low_get_home_sensor: start
[mustek_usb] usb_low_read_reg: Reg: 0x1f, Value: 0x60
[mustek_usb] usb_low_get_home_sensor: exit
(had to ctrl-C...)
modprobe scanner vendor=0x55f product=0x6
chmod 666 /dev/usb/scanner0
[11:26am 26-Apr-02]$ lsmod
Module Size Used by Tainted: P
agpgart 15520 3 (autoclean)
NVdriver 945504 10 (autoclean)
scanner 8416 0
ymfpci 40544 2
ac97_codec 9600 0 [ymfpci]
soundcore 3492 2 [ymfpci]
ntfs 50112 1 (autoclean)
uhci 23752 0 (unused)
mousedev 3808 1
hid 12864 0 (unused)
ide-cd 26848 0
loop 7888 0 (unused)
sg 24068 0
sr_mod 12824 0
ide-scsi 7488 0
cdrom 28672 0 [ide-cd sr_mod]
scsi_mod 51468 3 [sg sr_mod ide-scsi]
8139too 13504 1
Ive got a usb-mouse on the other port, with no problems...
pty: 256 Unix98 ptys configured
Uniform Multi-Platform E-IDE driver Revision: 6.31
ide: Assuming 33MHz system bus speed for PIO modes; override with
idebus=xx
PIIX4: IDE controller on PCI bus 00 dev 39
PIIX4: chipset revision 1
PIIX4: not 100% native mode: will probe irqs later
ide0: BM-DMA at 0xf000-0xf007, BIOS settings: hda:DMA, hdb:DMA
ide1: BM-DMA at 0xf008-0xf00f, BIOS settings: hdc:DMA, hdd:DMA
PDC20262: IDE controller on PCI bus 00 dev 70
PCI: Found IRQ 9 for device 00:0e.0
PDC20262: chipset revision 1
PDC20262: not 100% native mode: will probe irqs later
PDC20262: ROM enabled at 0xe7000000
PDC20262: (U)DMA Burst Bit ENABLED Primary PCI Mode Secondary PCI Mode.
ide2: BM-DMA at 0xc000-0xc007, BIOS settings: hde:DMA, hdf:pio
ide3: BM-DMA at 0xc008-0xc00f, BIOS settings: hdg:DMA, hdh:pio
hda: ASUS CRW-2410A, ATAPI CD/DVD-ROM drive
hdb: ASUS DVD-ROM E608, ATAPI CD/DVD-ROM drive
hde: ST330630A, ATA DISK drive
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
ide2 at 0xb000-0xb007,0xb402 on irq 9
blk: queue c032693c, I/O limit 4095Mb (mask 0xffffffff)
hde: 59777640 sectors (30606 MB) w/2048KiB Cache, CHS=59303/16/63,
UDMA(66)
Partition check:
hde: [PTBL] [3720/255/63] hde1 hde2 hde3 hde4 < hde5 >
Floppy drive(s): fd0 is 1.44M
FDC 0 is a post-1991 82077
Linux video capture interface: v1.00
usb.c: registered new driver usbdevfs
usb.c: registered new driver hub
NET4: Linux TCP/IP 1.0 for NET4.0
IP Protocols: ICMP, UDP, TCP, IGMP
IP: routing cache hash table of 4096 buckets, 32Kbytes
TCP: Hash tables configured (established 32768 bind 32768)
ip_tables: (C) 2000-2002 Netfilter core team
NET4: Unix domain sockets 1.0/SMP for Linux NET4.0.
XFS mounting filesystem ide2(33,2)
VFS: Mounted root (xfs filesystem) readonly.
Freeing unused kernel memory: 228k freed
Adding Swap: 305192k swap-space (priority -1)
8139too Fast Ethernet driver 0.9.24
PCI: Found IRQ 10 for device 00:0b.0
eth0: RealTek RTL8139 Fast Ethernet at 0xd8834000, 00:30:4f:0b:43:a8,
IRQ 10
eth0: Identified 8139 chip type 'RTL-8139C'
SCSI subsystem driver Revision: 1.00
scsi0 : SCSI host adapter emulation for IDE ATAPI devices
Vendor: ASUS Model: CRW-2410A Rev: 1.0
Type: CD-ROM ANSI SCSI revision: 02
Vendor: ASUS Model: DVD-ROM E608 Rev: 1.30
Type: CD-ROM ANSI SCSI revision: 02
Attached scsi CD-ROM sr0 at scsi0, channel 0, id 0, lun 0
Attached scsi CD-ROM sr1 at scsi0, channel 0, id 1, lun 0
sr0: scsi3-mmc drive: 40x/40x writer cd/rw xa/form2 cdda tray
Uniform CD-ROM driver Revision: 3.12
sr1: scsi3-mmc drive: 40x/40x cd/rw xa/form2 cdda tray
loop: loaded (max 8 devices)
usb.c: registered new driver hid
hid-core.c: v1.8.1 Andreas Gal, Vojtech Pavlik <vojtech at suse.cz>
hid-core.c: USB HID support drivers
mice: PS/2 mouse device common for all mice
uhci.c: USB Universal Host Controller Interface driver v1.1
uhci.c: USB UHCI at I/O 0xa000, IRQ 10
usb.c: new USB bus registered, assigned bus number 1
hub.c: USB hub found
hub.c: 2 ports detected
i2c-algo-bit.o: i2c bit algorithm module
bttv: driver version 0.7.91 loaded
bttv: using 2 buffers with 2080k (4160k total) for capture
bttv: Host bridge is Intel Corp. 440BX/ZX/DX - 82443BX/ZX/DX Host bridge
bttv: Host bridge needs ETBF enabled.
hub.c: USB new device connect on bus1/1, assigned device number 2
usb.c: USB device 2 (vend/prod 0x55f/0x6) is not claimed by any active
driver.
NTFS driver v1.1.22 [Flags: R/W MODULE]
hub.c: USB new device connect on bus1/2, assigned device number 3
hub.c: USB hub found
hub.c: 4 ports detected
eth0: Setting half-duplex based on auto-negotiated partner ability 0000.
hub.c: USB new device connect on bus1/2/1, assigned device number 4
input0,hiddev0: USB HID v1.00 Mouse [A4Tech USB Optical Mouse] on
usb1:4.0
hdb: CHECK for good STATUS
hda: CHECK for good STATUS
PCI: Found IRQ 5 for device 00:09.0
ymfpci: YMF744 at 0xe8020000 IRQ 5
ac97_codec: AC97 Audio codec, id: 0x8384:0x7608 (SigmaTel STAC9708)
usb.c: registered new driver usbscanner
scanner.c: probe_scanner: User specified USB scanner -- Vendor:Product -
55f:6
scanner.c: 0.4.6:USB Scanner Driver
[02:10pm 26-Apr-02]$ cat /proc/bus/usb/devices
T: Bus=01 Lev=00 Prnt=00 Port=00 Cnt=00 Dev#= 1 Spd=12 MxCh= 2
B: Alloc=115/900 us (13%), #Int= 3, #Iso= 0
D: Ver= 1.00 Cls=09(hub ) Sub=00 Prot=00 MxPS= 8 #Cfgs= 1
P: Vendor=0000 ProdID=0000 Rev= 0.00
S: Product=USB UHCI Root Hub
S: SerialNumber=a000
C:* #Ifs= 1 Cfg#= 1 Atr=40 MxPwr= 0mA
I: If#= 0 Alt= 0 #EPs= 1 Cls=09(hub ) Sub=00 Prot=00 Driver=hub
E: Ad=81(I) Atr=03(Int.) MxPS= 8 Ivl=255ms
T: Bus=01 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#= 2 Spd=1.5 MxCh= 0
D: Ver= 2.00 Cls=00(>ifc ) Sub=00 Prot=00 MxPS= 8 #Cfgs= 1
P: Vendor=09da ProdID=0006 Rev= 1.00
S: Manufacturer=A4Tech
S: Product=USB Optical Mouse
C:* #Ifs= 1 Cfg#= 1 Atr=a0 MxPwr=100mA
I: If#= 0 Alt= 0 #EPs= 1 Cls=03(HID ) Sub=01 Prot=02 Driver=hid
E: Ad=81(I) Atr=03(Int.) MxPS= 4 Ivl=10ms
T: Bus=01 Lev=01 Prnt=01 Port=01 Cnt=02 Dev#= 3 Spd=12 MxCh= 4
D: Ver= 1.10 Cls=09(hub ) Sub=00 Prot=00 MxPS= 8 #Cfgs= 1
P: Vendor=0000 ProdID=0e01 Rev= 0.04
S: Product=USB HUB
C:* #Ifs= 1 Cfg#= 1 Atr=e0 MxPwr=100mA
I: If#= 0 Alt= 0 #EPs= 1 Cls=09(hub ) Sub=00 Prot=00 Driver=hub
E: Ad=81(I) Atr=03(Int.) MxPS= 1 Ivl=255ms
T: Bus=01 Lev=02 Prnt=03 Port=00 Cnt=01 Dev#= 4 Spd=12 MxCh= 0
D: Ver= 1.00 Cls=00(>ifc ) Sub=00 Prot=00 MxPS= 8 #Cfgs= 1
P: Vendor=055f ProdID=0006 Rev= 1.00
C:* #Ifs= 1 Cfg#= 1 Atr=80 MxPwr=496mA
I: If#= 0 Alt= 0 #EPs= 3 Cls=00(>ifc ) Sub=00 Prot=00 Driver=usbscanner
E: Ad=01(O) Atr=02(Bulk) MxPS= 2 Ivl=0ms
E: Ad=82(I) Atr=02(Bulk) MxPS= 64 Ivl=0ms
E: Ad=83(I) Atr=03(Int.) MxPS= 1 Ivl=1ms
[02:10pm 26-Apr-02]$ cat /proc/bus/usb/drivers
usbdevfs
hub
hid
48- 63: usbscanner
usb_mouse
--
ph33r!
Linux mdew 2.4.19-pre7-xfs-aa #4 Fri Apr 26 12:14:19 NZST 2002 i686
unknown
GPG Key: http://mdew.orcon.net.nz/gpg
More information about the sane-devel
mailing list