[sane-devel] HP ScanJet 6100C Configuration

Peter Kirchgessner peter at kirchgessner.net
Sun Aug 4 09:06:07 BST 2002


Hi Frank,

try the hp.conf with

scsi HP
/dev/sg0

If this does not work, you may have a second hp.conf at 
/etc/sane.d/hp.conf. Try that one with the same content.
If it still does not work, do as root a

chmod 666 /dev/sg0

and try it again.

Sincerely

Peter

Frank Roberts - SOTL wrote:

> Hi All:
> 
> I hope You people will have time to help a relative novice with configuration 
> of an HP 6100 C which is to be used intermidently on 2 different RH 7.3 
> systems. 
> 
> 
> As stated previously the scanner is an HP 6100C if I issue the command:
> The scanner is connected by 40 pin scsi.
> Several commands were issues with the following results:
> 
> $ scanimage --list devices
> sg0     HP C2520A 36644
> sg1     Mitsumi    CD-R
> sg2     Soney      CD-RW
> 
> 
> $ cat /proc/scsi/scsa
> Attached devices: 
> Host: scsi0 Channel: 00 Id: 04 Lun: 00 Vendor: HP Model: C2520A Rev: 3644 
> Type: Processor ANSI SCSI revision: 02 
> Host: scsi1 Channel: 00 Id: 00 Lun: 00 Vendor: MITSUMI Model: CD-ROM FX4830T!B 
> Rev: R02C Type: CD-ROM ANSI SCSI revision: 02 
> Host: scsi1 Channel: 00 Id: 01 Lun: 00 Vendor: SONY Model: CD-RW CRX175E2 Rev: 
> S002 Type: CD-ROM ANSI SCSI revision: 02 
> 
> 
> $ export   SANE_DEBUGG_HP=17
> $ scanimage -L
> [scanei_debug] Setting debug level of hp to 17
> [hp] sane_init called[hp]
> [hp] sane_init will finish with Success
> [hp] sane_get_devices called
> [hp] hp_read_config: hp backend v0.95 start reading conf file
> [hp] hp_read_config: processing line <scsi HP>
> [hp] hp_read_config: processing line </dev/scaner>
> [hp] hp_read_config: attach scsi HP
> [hp] hp_read_config: attach /dev/scanner
> [hp] hp_get_dev: New device /dev/scanner, connect-scsi, scsi-request=1
> [hp] sanei_hp_device_new: /dev/scanner
> [hp] scsi_newopen failed (Invalid argument)
> [hp] /dev/scanner: Can't open scsi device
> [hp] sane_get_devices will finish with Success
> [hp] sane_exit called
> [hp] sane_exit will finish
> 
> 
> The sane configuration file /etc/sane.d/ho.conf is as follows:
> scsi HP
> /dev/scannet
> 
> I would appreciate any advice you people may be able to offer.
> 
> Thanks
> Frank 
> 
> Thanks
> 
> 
> 
> _______________________________________________
> Sane-devel mailing list
> Sane-devel at www.mostang.com
> http://www.mostang.com/mailman/listinfo/sane-devel
> 
> 


-- 
Peter Kirchgessner
http://www.kirchgessner.net
mailto:peter at kirchgessner.net




More information about the sane-devel mailing list