[sane-devel] HP ScanJet 6100C Configuration

[Frank Roberts - SOTL]

Thanks Peter

Software mission accomplished - Please see the attached file.

For scsi cards I will have to check on that. 
All I can say is that it did work with this scanner in this computer at one 
time. 

The other computer  is a dual boot with almost identical problems. On that 
computer the scanner does work under windows but does not work under linux 
showing almost the same set of problems. No data from the dual boot has been 
posted as I did not want to confuse the issue.

Both computers are loaded with pure RH 7.3 straight out of the box.

Thanks
Frank 

On Monday 05 August 2002 14:27, Peter Kirchgessner wrote:
> Hi Frank,
>
> lets start a new test with debugging information. Do
>
> export SANE_DEBUG_HP=17
> xscanimage hp > hp.lis 2>&1
> gzip hp.lis
>
> And please send back the file hp.lis.gz.
> BTW. What SCSI-card are you using with the scanner ?
>
> --Peter
>
> Frank Roberts - SOTL wrote:
> > Thanks again for the help Peter.
> > I did the following:
> > 1. Restored sane.d to its original configuration.
> > 2. In hp.conf changed /dev/scanner to /dev/sg0
> > 3. Confirmed that hp is active in dll.conf.
> > 4. Tested system - no change.
> > 5. As root did: chmood 666 /dev/sg0
> > 6. Tested system - no change.
> >
> > Thanks
> > Frank
> >
> > On Monday 05 August 2002 01:14, Peter Kirchgessner wrote:
> >>Don't remove the files. You need at least dll.conf too. And check that
> >>it has the line with hp activated.
> >>
> >>--Peter
> >>
> >>Frank Roberts - SOTL wrote:
> >>>Thanks for the help Peter.
> >>>
> >>>I did the following:
> >>>1. Changed /dev/scanner to /dev/sg0
> >>>2. Made directory sane.d-bak
> >>>3. Removed all configuration files from sane.d except hp.conf
> >>>4. As root did chmood 666 /dev/sg0
> >>>
> >>>I received exactly the same results - no change.
> >>>
> >>>Thanks
> >>>Frank
> >>>
> >>>On Sunday 04 August 2002 04:06, Peter Kirchgessner wrote:
> >>>>Hi Frank,
> >>>>
> >>>>try the hp.conf with
> >>>>scsi HP
> >>>>/dev/sg0
> >>>>
> >>>>If this does not work, you may have a second hp.conf at
> >>>>/etc/sane.d/hp.conf. Try that one with the same content.
> >>>>If it still does not work, do as root a
> >>>>
> >>>>chmod 666 /dev/sg0
> >>>>and try it again.
> >>>>
> >>>>Sincerely
> >>>>Peter
> >>>>
> >>>>Frank Roberts - SOTL wrote:
> >>>>>Hi All:
> >>>>>
> >>>>>I hope You people will have time to help a relative novice with
> >>>>>configuration of an HP 6100 C which is to be used intermidently on 2
> >>>>>different RH 7.3 systems.
> >>>>>
> >>>>>
> >>>>>As stated previously the scanner is an HP 6100C if I issue the
> >>>>> command: The scanner is connected by 40 pin scsi.
> >>>>>Several commands were issues with the following results:
> >>>>>
> >>>>>$ scanimage --list devices
> >>>>>sg0     HP C2520A 36644
> >>>>>sg1     Mitsumi    CD-R
> >>>>>sg2     Soney      CD-RW
> >>>>>
> >>>>>
> >>>>>$ cat /proc/scsi/scsa
> >>>>>Attached devices:
> >>>>>Host: scsi0 Channel: 00 Id: 04 Lun: 00 Vendor: HP Model: C2520A Rev:
> >>>>>3644 Type: Processor ANSI SCSI revision: 02
> >>>>>Host: scsi1 Channel: 00 Id: 00 Lun: 00 Vendor: MITSUMI Model: CD-ROM
> >>>>>FX4830T!B Rev: R02C Type: CD-ROM ANSI SCSI revision: 02
> >>>>>Host: scsi1 Channel: 00 Id: 01 Lun: 00 Vendor: SONY Model: CD-RW
> >>>>>CRX175E2 Rev: S002 Type: CD-ROM ANSI SCSI revision: 02
> >>>>>
> >>>>>
> >>>>>$ export   SANE_DEBUGG_HP=17
> >>>>>$ scanimage -L
> >>>>>[scanei_debug] Setting debug level of hp to 17
> >>>>>[hp] sane_init called[hp]
> >>>>>[hp] sane_init will finish with Success
> >>>>>[hp] sane_get_devices called
> >>>>>[hp] hp_read_config: hp backend v0.95 start reading conf file
> >>>>>[hp] hp_read_config: processing line <scsi HP>
> >>>>>[hp] hp_read_config: processing line </dev/scaner>
> >>>>>[hp] hp_read_config: attach scsi HP
> >>>>>[hp] hp_read_config: attach /dev/scanner
> >>>>>[hp] hp_get_dev: New device /dev/scanner, connect-scsi, scsi-request=1
> >>>>>[hp] sanei_hp_device_new: /dev/scanner
> >>>>>[hp] scsi_newopen failed (Invalid argument)
> >>>>>[hp] /dev/scanner: Can't open scsi device
> >>>>>[hp] sane_get_devices will finish with Success
> >>>>>[hp] sane_exit called
> >>>>>[hp] sane_exit will finish
> >>>>>
> >>>>>
> >>>>>The sane configuration file /etc/sane.d/ho.conf is as follows:
> >>>>>scsi HP
> >>>>>/dev/scannet
> >>>>>
> >>>>>I would appreciate any advice you people may be able to offer.
> >>>>>
> >>>>>Thanks
> >>>>>Frank
> >>>>>
> >>>>>Thanks
-------------- next part --------------
A non-text attachment was scrubbed...
Name: hp.lis.gz
Type: application/x-gzip
Size: 27 bytes
Desc: not available
URL: <http://alioth-lists.debian.net/pipermail/sane-devel/attachments/20020805/ca10d75d/attachment.bin>