[sane-devel] SANE HP 4P SCSI scanner error message

[Johan van den Berg]

Hi,

I'm geeting the following error message while trying
to get scanimage -L to work with my HP 4P SCSI scanner
on Linux using the supplied SCSI interface card:
scl_inq: malformed response: expected '257d', got
'257E'

Any ideas?

My setup and output is as follows:

root# sane-find-scanner
sane-find-scanner: found SCSI processor "HP C1130A
3540" at device/dev/scanner
sane-find-scanner: found SCSI processor "HP C1130A
3540" at device /dev/sg0
sane-find-scanner: found SCSI processor "HP C1130A
3540" at device /dev/sga

root# scanimage -L
[sanei_debug] Setting debug level of hp to 128.
[hp] sane_init called
[hp] sane_init will finish with Success
[hp] sane_get_devices called
[hp] hp_read_config: hp backend v0.95 starts reading
config file
[hp] hp_read_config: processing line <scsi HP * * * *
* *>
[hp] hp_read_config: processing line </dev/sg0>
[hp] hp_read_config: attach scsi HP * * * * * *
[hp] hp_get_dev: New device /dev/sg0, connect-scsi,
scsi-request=1
[hp] sanei_hp_device_new: /dev/sg0
[hp] scsi_inquire: sending INQUIRE
[hp] scsi_new: sending TEST_UNIT_READY
[hp] scsi_flush: writing 2 bytes:
[hp]  0x0000  1B 45                                   
        .E
[hp] scsi_flush: writing 7 bytes:
[hp]  0x0000  1B 2A 73 32 35 37 45                    
        .*s257E
[hp] scsi_read:  16 bytes:
[hp]  0x0000  1B 2A 73 32 35 37 45 00 48 50 20 20 20
20 20 20  .*s257E.HP
[hp] scl_inq: malformed response: expected '257d', got
'257E'
[hp] scl_errcheck: Can't read SCL error stack: Error
during device I/O
[hp] sanei_hp_device_new: SCL reset failed
[hp] scsi_close: closing fd 5
[hp] hp_read_config: processing line <option
connect-device>
[hp] hp_read_config: attach /dev/sg0
[hp] hp_get_dev: New device /dev/sg0, connect-device,
scsi-request=0
[hp] sanei_hp_device_new: /dev/sg0
[hp] scsi_flush: writing 2 bytes:
[hp]  0x0000  1B 45                                   
        .E
[hp] hp_nonscsi_device_new: SCL reset failed
[hp] scsi_close: closing fd 4
[hp] sane_get_devices will finish with Success

No scanners were identified. If you were expecting
something different,
check that the scanner is plugged in, turned on and
detected by the
sane-find-scanner tool (if appropriate). Please read
the documentation
which came with this software (README, FAQ, manpages).
[hp] sane_exit called
[hp] sane_exit will finish

root# cat /proc/scsi/scsi
Attached devices:
Host: scsi0 Channel: 00 Id: 01 Lun: 00
  Vendor: HP       Model: C1130A           Rev: 3540
  Type:   Processor                        ANSI SCSI
revision: 02

root# cat /proc/scsi/sym53c416/0
Symbios Logic 53c416 (rev. 0) at 0x220, irq 5, SCSI-ID
7, fast pio

I'm using a Mandrake 8.2 based system with 2.4.18-6mdk
kernel.

Thx
Johan


__________________________________________________
Do You Yahoo!?
HotJobs - Search Thousands of New Jobs
http://www.hotjobs.com