[sane-devel] Resend: scanjet 5p, io-error

[SITKEI Attila]

greetings,

I've recently tried my HP ScanJet 5p scanner, that is attached to my PC
through an Initio-9100uw scsi interface. After recompiled 

uuu $ uname -a
FreeBSD uuu.pmi 4.6.2-RELEASE-p4 FreeBSD 4.6.2-RELEASE-p4 #3: Wed Nov 13
08:23:20 CET 2002     teflon at uuu.pmi:/usr/src/sys/compile/UUU  i386

kernel, my machine found:

uuu $ dmesg | grep Ini
iha0: <Initio INI-9XXXU/UW PCI SCSI adapter> port 0xac00-0xacff mem
0xdfeff000-0xdfefffff irq 10 at device 9.0 on pci2

and 

uuu $ dmesg | grep pass0
pass0 at iha0 bus 0 target 2 lun 0
pass0: <HP C5110A 3701> Fixed Processor SCSI-2 device 
pass0: 40.000MB/s transfers (20.000MHz, offset 15, 16bit)

so I though everything will work well, since my scanner is shown as
supported
model on 
http://www.mostang.com/sane/sane-mfgs.html#HEWLETT-PACKARD

I've installed sane-backends-1.0.8 from ports, did:


uuu $ sane-find-scanner 

found SCSI processor "HP C5110A 3701" at /dev/scanner
found SCSI processor "HP C5110A 3701" at /dev/pass0
[...]

uuu $ export SANE_DEBUG_HP=128; scanimage -L
[sanei_debug] Setting debug level of hp to 128.
[hp] sane_init called
[hp] sane_init will finish with Success
[hp] sane_get_devices called
[hp] hp_read_config: hp backend v0.96 starts reading config file
[hp] hp_read_config: processing line <scsi HP>
[hp] hp_read_config: processing line </dev/scanner>
[hp] hp_read_config: attach scsi HP
[hp] hp_get_dev: New device /dev/pass0, connect-scsi, scsi-request=1
[hp] sanei_hp_device_new: /dev/pass0
[hp] scsi_inquire: sending INQUIRE
[hp] scsi_new: sending TEST_UNIT_READY
[hp] scsi_flush: writing 2 bytes:
[hp]  0x0000  1B 45                                            .E
[hp] scsi_flush: writing 7 bytes:
[hp]  0x0000  1B 2A 73 32 35 37 45                             .*s257E
[hp] scl_inq: read failed (Error during device I/O)
[hp] scl_errcheck: Can't read SCL error stack: Error during device I/O
[hp] sanei_hp_device_new: SCL reset failed
[hp] scsi_close: closing fd 0
[hp] hp_read_config: processing line <option disable-scsi-request>
[hp] hp_read_config: processing line <# uncomment this if you're using a usb
scanner>
[hp] hp_read_config: processing line <# /dev/usb/scanner0>
[hp] hp_read_config: processing line <#   option connect-device>
[hp] hp_read_config: attach /dev/scanner
[hp] hp_get_dev: New device /dev/scanner, connect-scsi, scsi-request=0
[hp] sanei_hp_device_new: /dev/scanner
[hp] scsi_inquire: sending INQUIRE
[hp] scsi_new: sending TEST_UNIT_READY
[hp] scsi_flush: writing 2 bytes:
[hp]  0x0000  1B 45                                            .E
[hp] scsi_flush: writing 7 bytes:
[hp]  0x0000  1B 2A 73 32 35 37 45                             .*s257E
[hp] scl_inq: read failed (Error during device I/O)
[hp] scl_errcheck: Can't read SCL error stack: Error during device I/O
[hp] sanei_hp_device_new: SCL reset failed
[hp] scsi_close: closing fd 0
[hp] hp_read_config: reset to default config
[hp] sane_get_devices will finish with Success

No scanners were identified. If you were expecting something different,
check that the scanner is plugged in, turned on and detected by the
sane-find-scanner tool (if appropriate). Please read the documentation
which came with this software (README, FAQ, manpages).
[hp] sane_exit called
[hp] sane_exit will finish


at this point I can't resolve the problem. Has anybody idea about?
just for info: I've also tried the newer backend, similar results. the
scsi-card works with an external cd-writer unit.


Thanks in advance, regards 



-- tef