[sane-devel] Blank Page with Cybercom 9352 parallel port

[Michael Gruner]

Hello,

trying to get my scanner working there is some trouble:
As mentioned in the topic I have a Cybercom 9352. But this is just like
the medion scanners a Mustek. Looking through the
windows\twain_32\install.log it was installed as a mustek 1200 cp. Ok,
so i decided to use the sane mustek_pp backend for it. Executing a
"scanimage -L" tells me the device is a MFS-600IIIP. Now I'm totaly
confused: what's right and what is wrong? Hopefully someone of you can
me how I can get that scanner working with sane. Here is the output of
an "scanimage -T"

[sanei_debug] Setting debug level of mustek_pp to 128.
[mustek_pp] init: SANE v1.0.8, backend v1.0.9-devel
[mustek_pp] I wouldn't let myself be root if I were you...
[mustek_pp] init: option io-mode 1
[mustek_pp] init: option io-mode 3
[mustek_pp] init: trying port `0x378'
[mustek_pp] attach: device 0x378 attached
[mustek_pp] attach: asic 0xa5, ccd 01
[mustek_pp] attach: use600 is `no'
[mustek_pp] init: device 0x378 is a 600 dpi scanner
[mustek_pp] init: option strip-height 16
[mustek_pp] init: setting strip-height to 16 for device 0x378
[mustek_pp] init: option buffer 122400
[mustek_pp] init: setting buffer to 122400 for device 0x378
[mustek_pp] open: device `0x378'
[mustek_pp] open: range (0.0,0.0)-(220.133316,296.333313)
[mustek_pp] mustek_pp(v1.0.9-devel): line 2703: debug exception
[mustek_pp] ASSERT((dev->asic_id == 0xA8) || ((dev->asic_id == 0xA5) &&
(dev->ccd_type == 0))) failed
[mustek_pp] expect disaster...
[mustek_pp] config_ccd: 600 dpi, mode 2, invert 0, size 10
[mustek_pp] set_dpi_value: value 0x21
[mustek_pp] set_line_adjust: value = 82 (0x0052)
[mustek_pp] set_line_adjust: ppl 10 (0), adjust 82, skip 0
[mustek_pp] motor_controll_1015: control code 0xd3
[mustek_pp] config_ccd: 600 dpi, mode 2, invert 0, size 10
[mustek_pp] set_dpi_value: value 0x21
[mustek_pp] set_line_adjust: value = 82 (0x0052)
[mustek_pp] set_line_adjust: ppl 10 (0), adjust 82, skip 0
[mustek_pp] open: success
[mustek_pp] control_option: option 0, action 0
[mustek_pp] control_option: option 0, action 0
[mustek_pp] get_option_descriptor: requested option 0 ((null))
[mustek_pp] get_option_descriptor: requested option 1 ((null))
[mustek_pp] get_option_descriptor: requested option 2 (mode)
[mustek_pp] get_option_descriptor: requested option 3 (resolution)
[mustek_pp] get_option_descriptor: requested option 4 (preview)
[mustek_pp] get_option_descriptor: requested option 5 (preview-in-gray)
[mustek_pp] get_option_descriptor: requested option 6 ((null))
[mustek_pp] get_option_descriptor: requested option 7 (tl-x)
[mustek_pp] get_option_descriptor: requested option 8 (tl-y)
[mustek_pp] get_option_descriptor: requested option 9 (br-x)
[mustek_pp] control_option: option 9, action 0
[mustek_pp] get_option_descriptor: requested option 10 (br-y)
[mustek_pp] control_option: option 10, action 0
[mustek_pp] get_option_descriptor: requested option 11 ((null))
[mustek_pp] get_option_descriptor: requested option 12 (custom-gamma)
[mustek_pp] get_option_descriptor: requested option 13 (gamma-table)
[mustek_pp] get_option_descriptor: requested option 14 (red-gamma-table)
[mustek_pp] get_option_descriptor: requested option 15
(green-gamma-table)
[mustek_pp] get_option_descriptor: requested option 16
(blue-gamma-table)
[mustek_pp] control_option: option 7, action 0
[mustek_pp] control_option: option 8, action 0
[mustek_pp] control_option: option 7, action 0
[mustek_pp] get_option_descriptor: requested option 9 (br-x)
[mustek_pp] control_option: option 9, action 1
[mustek_pp] control_option: option 8, action 0
[mustek_pp] get_option_descriptor: requested option 10 (br-y)
[mustek_pp] control_option: option 10, action 1
[mustek_pp] get_parameters: mode `Color'
[mustek_pp] get_parameters: 600 dpi
[mustek_pp] get_parameters: resolution 600 dpi -> hardware 600 dpi
[mustek_pp] get_parameters: 5200x7000 pixels
[mustek_pp] start: maybe waiting for lamp...
[mustek_pp] config_ccd: 600 dpi, mode 2, invert 0, size 5200
[mustek_pp] set_dpi_value: value 0x21
[mustek_pp] set_line_adjust: value = 41602 (0xa282)
[mustek_pp] set_line_adjust: ppl 5200 (5200), adjust 41602, skip 0
[mustek_pp] motor_controll_1015: control code 0xd3
[mustek_pp] config_ccd: 600 dpi, mode 2, invert 0, size 5200
[mustek_pp] set_dpi_value: value 0x21
[mustek_pp] set_line_adjust: value = 41602 (0xa282)
[mustek_pp] set_line_adjust: ppl 5200 (5200), adjust 41602, skip 0
[mustek_pp] start: executing calibration
[mustek_pp] calibrate entered (asic = 0xa5)
[mustek_pp] calibrate_device_101x: use600 = yes
[mustek_pp] config_ccd: 600 dpi, mode 2, invert 0, size 10
[mustek_pp] set_dpi_value: value 0x21
[mustek_pp] set_line_adjust: value = 82 (0x0052)
[mustek_pp] set_line_adjust: ppl 10 (5200), adjust 82, skip 0
[mustek_pp] config_ccd: 300 dpi, mode 2, invert 0, size 150
[mustek_pp] set_dpi_value: value 0x51
[mustek_pp] set_line_adjust: value = 1202 (0x04b2)
[mustek_pp] set_line_adjust: ppl 150 (5200), adjust 1202, skip 0
[mustek_pp] motor_controll_1015: control code 0x43
[mustek_pp] motor_controll_1015: control code 0x43
[mustek_pp] motor_controll_1015: control code 0x43
[mustek_pp] motor_controll_1015: control code 0x43
[mustek_pp] config_ccd: 600 dpi, mode 1, invert 0, size 5200
[mustek_pp] set_dpi_value: value 0x21
[mustek_pp] set_line_adjust: value = 5202 (0x1452)
[mustek_pp] set_line_adjust: ppl 5200 (5200), adjust 5202, skip 0
[mustek_pp] motor_controll_1015: control code 0x43 <--this message is
repeated some times...(about 30 repeats)
[mustek_pp] config_ccd: 600 dpi, mode 2, invert 0, size 5200
[mustek_pp] set_dpi_value: value 0x21
[mustek_pp] set_line_adjust: value = 41602 (0xa282)
[mustek_pp] set_line_adjust: ppl 5200 (5200), adjust 41602, skip 4
[mustek_pp] motor_controll_1015: control code 0x43<--this message is
repeated some times...(about 30 repeats)
[mustek_pp] config_ccd: 600 dpi, mode 2, invert 0, size 5200
[mustek_pp] set_dpi_value: value 0x21
[mustek_pp] set_line_adjust: value = 41602 (0xa282)
[mustek_pp] set_line_adjust: ppl 5200 (5200), adjust 41602, skip 4
[mustek_pp] calibrate: ref_black 0, blackpos 106
[mustek_pp] move_motor: 128 steps (forward)
[mustek_pp] motor_controll_1015: control code 0x63 <--this message is
repeated some times...(about 30 repeats)
[mustek_pp] start: device ready for scanning
[mustek_pp] get_parameters: can't set parameters while scanning
[mustek_pp] mustek_pp(v1.0.9-devel): line 3914: debug exception
scanimage: scanning image of size 5200x7000 pixels at 24 bits/pixel
scanimage: acquiring RGB frame, 8 bits/sample
scanimage: reading one scanline, 15600 bytes...	[mustek_pp] read:
scanning next 7 lines
[mustek_pp] motor_controll_1015: control code 0x43<--this message is
repeated some times...(about 10 repeats)
[mustek_pp] read: delivering 15600 bytes
PASS
scanimage: reading one byte...		[mustek_pp] read: delivering 1 bytes
PASS
scanimage: stepped read, 2 bytes... 	[mustek_pp] read: delivering 2
bytes
PASS
scanimage: stepped read, 4 bytes... 	[mustek_pp] read: delivering 4
bytes
PASS
scanimage: stepped read, 8 bytes... 	[mustek_pp] read: delivering 8
bytes
PASS
scanimage: stepped read, 16 bytes... 	[mustek_pp] read: delivering 16
bytes
PASS
scanimage: stepped read, 32 bytes... 	[mustek_pp] read: delivering 32
bytes
PASS
scanimage: stepped read, 64 bytes... 	[mustek_pp] read: delivering 64
bytes
PASS
scanimage: stepped read, 128 bytes... 	[mustek_pp] read: delivering 128
bytes
PASS
scanimage: stepped read, 256 bytes... 	[mustek_pp] read: delivering 256
bytes
PASS
scanimage: stepped read, 512 bytes... 	[mustek_pp] read: delivering 512
bytes
PASS
scanimage: stepped read, 1024 bytes... 	[mustek_pp] read: delivering
1024 bytes
PASS
scanimage: stepped read, 2048 bytes... 	[mustek_pp] read: delivering
2048 bytes
PASS
scanimage: stepped read, 4096 bytes... 	[mustek_pp] read: delivering
4096 bytes
PASS
scanimage: stepped read, 8192 bytes... 	[mustek_pp] read: delivering
8192 bytes
PASS
scanimage: stepped read, 16384 bytes... 	[mustek_pp] read: delivering
16384 bytes
PASS
scanimage: stepped read, 16383 bytes... 	[mustek_pp] read: delivering
16383 bytes
PASS
scanimage: stepped read, 8191 bytes... 	[mustek_pp] read: delivering
8191 bytes
PASS
scanimage: stepped read, 4095 bytes... 	[mustek_pp] read: delivering
4095 bytes
PASS
scanimage: stepped read, 2047 bytes... 	[mustek_pp] read: delivering
2047 bytes
PASS
scanimage: stepped read, 1023 bytes... 	[mustek_pp] read: delivering
1023 bytes
PASS
scanimage: stepped read, 511 bytes... 	[mustek_pp] read: delivering 511
bytes
PASS
scanimage: stepped read, 255 bytes... 	[mustek_pp] read: delivering 255
bytes
PASS
scanimage: stepped read, 127 bytes... 	[mustek_pp] read: delivering 127
bytes
PASS
scanimage: stepped read, 63 bytes... 	[mustek_pp] read: delivering 63
bytes
PASS
scanimage: stepped read, 31 bytes... 	[mustek_pp] read: delivering 31
bytes
PASS
scanimage: stepped read, 15 bytes... 	[mustek_pp] read: delivering 15
bytes
PASS
scanimage: stepped read, 7 bytes... 	[mustek_pp] read: delivering 7
bytes
PASS
scanimage: stepped read, 3 bytes... 	[mustek_pp] read: delivering 3
bytes
PASS
[mustek_pp] cancel: stopping current scan
[mustek_pp] config_ccd: 600 dpi, mode 2, invert 0, size 5200
[mustek_pp] set_dpi_value: value 0x21
[mustek_pp] set_line_adjust: value = 41602 (0xa282)
[mustek_pp] set_line_adjust: ppl 5200 (5200), adjust 41602, skip 0
[mustek_pp] motor_controll_1015: control code 0xd3
[mustek_pp] config_ccd: 600 dpi, mode 2, invert 0, size 5200
[mustek_pp] set_dpi_value: value 0x21
[mustek_pp] set_line_adjust: value = 41602 (0xa282)
[mustek_pp] set_line_adjust: ppl 5200 (5200), adjust 41602, skip 4
[mustek_pp] close: maybe waiting for lamp...
[mustek_pp] config_ccd: 600 dpi, mode 2, invert 0, size 5200
[mustek_pp] set_dpi_value: value 0x21
[mustek_pp] set_line_adjust: value = 41602 (0xa282)
[mustek_pp] set_line_adjust: ppl 5200 (5200), adjust 41602, skip 0
[mustek_pp] motor_controll_1015: control code 0xd3
[mustek_pp] config_ccd: 600 dpi, mode 2, invert 0, size 5200
[mustek_pp] set_dpi_value: value 0x21
[mustek_pp] set_line_adjust: value = 41602 (0xa282)
[mustek_pp] set_line_adjust: ppl 5200 (5200), adjust 41602, skip 4
[mustek_pp] close: device closed
[mustek_pp] exit: (...)

micha

-- 
Windmuehlenweg 22 07907 Schleiz
mobil: +491628955029
e-Mail: Michael.Gruner@fh-hof.de

__________________________________________________________________

Gesendet von Yahoo! Mail - http://mail.yahoo.de
Yahoo! präsentiert als offizieller Sponsor das Fußball-Highlight des
Jahres: - http://www.FIFAworldcup.com