[sane-devel] Epson Perfection 2400 on RH 9

[sane@vikas.mailshell.com]

>From Henning Meier-Geinitz <henning@meier-geinitz.de> on 10 Dec 2003:

> Please show us the output of 
> SANE_DEBUG_EPSON=255 scanimage -L
> 
> If there is no output but the "no device found" messages, have a look
> at the archive of sane-devel. I've written about a similar case some
> minutes ago.


[vikas@upstairs sane-backends-1.0.13]$ SANE_DEBUG_EPSON=255 scanimage -L

No scanners were identified. If you were expecting something different,
check that the scanner is plugged in, turned on and detected by the
sane-find-scanner tool (if appropriate). Please read the documentation
which came with this software (README, FAQ, manpages).

[vikas@upstairs sane-backends-1.0.13]$ sane-find-scanner

  # No SCSI scanners found. If you expected something different, make sure that
  # you have loaded a SCSI driver for your SCSI adapter.

found USB scanner (vendor=0x04b8, product=0x011b) at /dev/usb/scanner0
found USB scanner (vendor=0x04b8, product=0x011b) at libusb:001:002
  # Your USB scanner was (probably) detected. It may or may not be supported by
  # SANE. Try scanimage -L and read the backend's manpage.

  # Scanners connected to the parallel port or other proprietary ports can't be
  # detected by this program.

  # You may want to run this program as root to find all devices. Once you
  # found the scanner devices, be sure to adjust access permissions as
  # necessary.

ls -l /dev/usb/scanner0

[vikas@upstairs sane-backends-1.0.13]$ ls -l /dev/usb/scanner0
crw-rw-rw-    1 root     root     180,  48 Jan 30  2003 /dev/usb/scanner0

As root, /sbin/lsusb gives me

Bus 001 Device 002: ID 04b8:011b Seiko Epson Corp.
Device Descriptor:
  bLength                18
  bDescriptorType         1
  bcdUSB               2.00
  bDeviceClass          255 Vendor Specific Class
  bDeviceSubClass       255 Vendor Specific Subclass
  bDeviceProtocol       255 Vendor Specific Protocol
  bMaxPacketSize0        64
  idVendor           0x04b8 Seiko Epson Corp.
  idProduct          0x011b
  bcdDevice            1.00
  iManufacturer           1 EPSON
  iProduct                2 EPSON Scanner
  iSerial                 0
  bNumConfigurations      1

cat /proc/bus/usb/devices gives me

T:  Bus=01 Lev=01 Prnt=01 Port=01 Cnt=01 Dev#=  2 Spd=480 MxCh= 0
D:  Ver= 2.00 Cls=ff(vend.) Sub=ff Prot=ff MxPS=64 #Cfgs=  1
P:  Vendor=04b8 ProdID=011b Rev= 1.00
S:  Manufacturer=EPSON
S:  Product=EPSON Scanner
C:* #Ifs= 1 Cfg#= 1 Atr=c0 MxPwr=  2mA
I:  If#= 0 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=usbscanner
E:  Ad=81(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms



I searched the archives, didnt find anything relevant. Please repost? Thanks

_______________________________________________________
The FREE service that prevents junk email http://www.mailshell.com