[sane-devel] saned issues for remote scanner access

[Jim George]

Hi,

>
> I don't know. Can you post the complete log including the sane_init
> messages from the gt68xx backend? Maybe even some more debugging:
>
> SANE_DEBUG_DLL=255 SANE_DEBUG_GT68XX=255 saned -d128
>
Please find attached.

Hope this helps,

Jim


-------------- next part --------------
SANE_DEBUG_SANEI_PA4S2=255 saned -d128
[saned] main: starting debug mode (level 128)
[saned] main: trying to get port for service `sane' (getaddrinfo)
[saned] main: [0] socket () using IPv6
[saned] main: [0] setsockopt ()
[saned] main: [0] bind () to port 6566
[saned] main: [0] listen ()
[saned] main: [1] socket () using IPv4
[saned] main: [1] setsockopt ()
[saned] main: [1] bind () to port 6566
[saned] main: [1] bind failed: Address already in use
[saned] main: waiting for control connection
[saned] saned (AF-indep+IPv6) from sane-backends 1.0.13 ready
[saned] check_host: detected an IPv4-mapped address
[saned] check_host: access by remote host: ::ffff:192.168.0.16
[saned] check_host: remote host is not IN_LOOPBACK nor IN6_LOOPBACK
[saned] check_host: local hostname: tassi
[saned] check_host: local hostname(s) (from DNS): tassi.local
[saned] check_host: local hostname(s) (from DNS): tassi.local
[saned] check_host: local hostname(s) (from DNS): tassi.local
[saned] check_host: remote host doesn't have same addr as local
[saned] check_host: opening config file: /etc/hosts.equiv
[saned] check_host: config file line: `#'
[saned] check_host: config file line: `# hosts.equiv   This file describes the names of the hosts which are'
[saned] check_host: config file line: `#		to be considered "equivalent", i.e. which are to be'
[saned] check_host: config file line: `#		trusted enough for allowing rsh(1) commands.'
[saned] check_host: config file line: `#'
[saned] check_host: config file line: `# hostname'
[saned] check_host: config file line: `'
[saned] check_host: opening config file: saned.conf
[saned] check_host: config file line: `#'
[saned] check_host: config file line: `# saned.conf'
[saned] check_host: config file line: `#'
[saned] check_host: config file line: `# The contents of the saned.conf  file  is  a  list  of  host  names,  IP'
[saned] check_host: config file line: `# addresses or IP subnets (CIDR notation) that are permitted to use local'
[saned] check_host: config file line: `# SANE devices. IPv6 addresses must be enclosed in brackets,  and  should'
[saned] check_host: config file line: `# always  be specified in their compressed form.'
[saned] check_host: config file line: `#'
[saned] check_host: config file line: `# The hostname matching is not case-sensitive.'
[saned] check_host: config file line: `#'
[saned] check_host: config file line: `#scan-client.somedomain.firm'
[saned] check_host: config file line: `#192.168.0.1'
[saned] check_host: config file line: `192.168.0.1/29'
[saned] check_host: subnet with base IP = 192.168.0.1, CIDR netmask = 29
[saned] check_host: config file line: `+'
[saned] check_host: access granted from any host (`+')
[saned] init: access granted
[saned] init: access granted to jgeorge@::ffff:192.168.0.16
[saned] process_request: waiting for request
[saned] process_request: got request 1
[saned] process_request: waiting for request
[saned] process_request: got request 2
[saned] process_request: (open) strlen(resource) == 0
[saned] process_request: access to resource `gt68xx' granted
[saned] process_request: waiting for request
[saned] process_request: got request 8
[saned] decode_handle: cancel: error while decoding handle argument (h=0, Success)
Segmentation fault
tassi:~ #