[sane-devel] re epson perfection 1200 problems libusb kernel 2.6.1-rc1
Jim Quigley
jimquigley9@eircom.net
Sat, 17 Jan 2004 01:52:18 +0000
This is a multi-part message in MIME format.
--------------090808010205010105020404
Content-Type: text/plain; charset=us-ascii; format=flowed
Content-Transfer-Encoding: 7bit
Hi I have installed the kernel 2.6.1-rc1 over Suse 9 and have as far as
I know installed most usb drivers as modules except the scanner.o module
since it is obsolete and I wanted to use libusb. I have an epson
perfection 1200 photo scanner but I can not get it to work properly. It
initialises but then crashes and then scanimage -L does not recognise
it. Xsane also does the same. Below are some of the programs I use and
some config files including sane, xsane, fstab, dmesg etc. Appreciate
some help. Thanks
rpm -q sane
sane-1.0.10-243
rpm -q xsane
xsane-0.91-135
rpm -q hotplug
hotplug-2002_08_26-85
cat /etc/fstab
/dev/hdc1 / ext2
defaults 1 1
/dev/hdc2 /home ext2
defaults 1 2
/dev/hdc3 swap swap
pri=42 0 0
devpts /dev/pts devpts
mode=0620,gid=5 0 0
proc /proc proc
defaults 0 0
none /proc/bus/usb usbfs defaults 0 0
/dev/cdrom /media/cdrom auto
ro,noauto,user,exec 0 0
/dev/dvd /media/dvd auto
ro,noauto,user,exec 0 0
/dev/fd0 /media/floppy auto
noauto,user,sync 0 0
/dev/sr0 /media/sr0 auto ro,noauto,user,exec 0 0
/dev/sda1 /media/sda1 auto sync,noauto,user,exec 0 0
cat /proc/bus/usb/devices
T: Bus=04 Lev=00 Prnt=00 Port=00 Cnt=00 Dev#= 1 Spd=12 MxCh= 2
B: Alloc= 0/900 us ( 0%), #Int= 0, #Iso= 0
D: Ver= 1.10 Cls=09(hub ) Sub=00 Prot=00 MxPS= 8 #Cfgs= 1
P: Vendor=0000 ProdID=0000 Rev= 2.06
S: Manufacturer=Linux 2.6.1-rc1 uhci_hcd
S: Product=UHCI Host Controller
S: SerialNumber=0000:00:10.2
C:* #Ifs= 1 Cfg#= 1 Atr=40 MxPwr= 0mA
I: If#= 0 Alt= 0 #EPs= 1 Cls=09(hub ) Sub=00 Prot=00 Driver=hub
E: Ad=81(I) Atr=03(Int.) MxPS= 2 Ivl=255ms
T: Bus=04 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#= 2 Spd=12 MxCh= 0
D: Ver= 1.00 Cls=07(print) Sub=01 Prot=02 MxPS=64 #Cfgs= 1
P: Vendor=04b8 ProdID=0001 Rev= 1.00
S: Manufacturer=EPSON
S: Product=USB Printer
C:* #Ifs= 1 Cfg#= 1 Atr=40 MxPwr= 2mA
I: If#= 0 Alt= 0 #EPs= 2 Cls=07(print) Sub=01 Prot=02 Driver=usblp
E: Ad=01(O) Atr=02(Bulk) MxPS= 64 Ivl=0ms
E: Ad=82(I) Atr=02(Bulk) MxPS= 64 Ivl=0ms
T: Bus=03 Lev=00 Prnt=00 Port=00 Cnt=00 Dev#= 1 Spd=12 MxCh= 2
B: Alloc= 0/900 us ( 0%), #Int= 0, #Iso= 0
D: Ver= 1.10 Cls=09(hub ) Sub=00 Prot=00 MxPS= 8 #Cfgs= 1
P: Vendor=0000 ProdID=0000 Rev= 2.06
S: Manufacturer=Linux 2.6.1-rc1 uhci_hcd
S: Product=UHCI Host Controller
S: SerialNumber=0000:00:10.1
C:* #Ifs= 1 Cfg#= 1 Atr=40 MxPwr= 0mA
I: If#= 0 Alt= 0 #EPs= 1 Cls=09(hub ) Sub=00 Prot=00 Driver=hub
E: Ad=81(I) Atr=03(Int.) MxPS= 2 Ivl=255ms
T: Bus=03 Lev=01 Prnt=01 Port=01 Cnt=01 Dev#= 2 Spd=12 MxCh= 0
D: Ver= 1.00 Cls=ff(vend.) Sub=ff Prot=ff MxPS=64 #Cfgs= 1
P: Vendor=04b8 ProdID=0104 Rev= 1.03
S: Manufacturer=EPSON
S: Product=Perfection1200
C:* #Ifs= 1 Cfg#= 1 Atr=40 MxPwr= 2mA
I: If#= 0 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=(none)
E: Ad=81(I) Atr=02(Bulk) MxPS= 64 Ivl=0ms
E: Ad=02(O) Atr=02(Bulk) MxPS= 64 Ivl=0ms
T: Bus=02 Lev=00 Prnt=00 Port=00 Cnt=00 Dev#= 1 Spd=12 MxCh= 2
B: Alloc= 0/900 us ( 0%), #Int= 0, #Iso= 0
D: Ver= 1.10 Cls=09(hub ) Sub=00 Prot=00 MxPS= 8 #Cfgs= 1
P: Vendor=0000 ProdID=0000 Rev= 2.06
S: Manufacturer=Linux 2.6.1-rc1 uhci_hcd
S: Product=UHCI Host Controller
S: SerialNumber=0000:00:10.0
C:* #Ifs= 1 Cfg#= 1 Atr=40 MxPwr= 0mA
I: If#= 0 Alt= 0 #EPs= 1 Cls=09(hub ) Sub=00 Prot=00 Driver=hub
E: Ad=81(I) Atr=03(Int.) MxPS= 2 Ivl=255ms
T: Bus=01 Lev=00 Prnt=00 Port=00 Cnt=00 Dev#= 1 Spd=480 MxCh= 6
B: Alloc= 0/800 us ( 0%), #Int= 0, #Iso= 0
D: Ver= 2.00 Cls=09(hub ) Sub=00 Prot=01 MxPS= 8 #Cfgs= 1
P: Vendor=0000 ProdID=0000 Rev= 2.06
S: Manufacturer=Linux 2.6.1-rc1 ehci_hcd
S: Product=EHCI Host Controller
S: SerialNumber=0000:00:10.3
C:* #Ifs= 1 Cfg#= 1 Atr=40 MxPwr= 0mA
I: If#= 0 Alt= 0 #EPs= 1 Cls=09(hub ) Sub=00 Prot=00 Driver=hub
E: Ad=81(I) Atr=03(Int.) MxPS= 2 Ivl=256ms
T: Bus=01 Lev=01 Prnt=01 Port=01 Cnt=01 Dev#= 2 Spd=480 MxCh= 0
D: Ver= 2.00 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs= 1
P: Vendor=0d49 ProdID=3005 Rev= 1.00
S: Manufacturer=Maxtor
S: Product=3000LS v01.00.00
S: SerialNumber=DEF10647FBB9
C:* #Ifs= 1 Cfg#= 1 Atr=c0 MxPwr= 0mA
I: If#= 0 Alt= 0 #EPs= 2 Cls=08(stor.) Sub=06 Prot=50 Driver=usb-storage
E: Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=88(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
sane-find-scanner
# No SCSI scanners found. If you expected something different, make
sure that
# you have loaded a SCSI driver for your SCSI adapter.
found USB scanner (vendor=0x04b8, product=0x0104) at libusb:003:002
# Your USB scanner was (probably) detected. It may or may not be
supported by
# SANE. Try scanimage -L and read the backend's manpage.
# Scanners connected to the parallel port or other proprietary ports
can't be
# detected by this program.
# You may want to run this program as root to find all devices. Once you
# found the scanner devices, be sure to adjust access permissions as
# necessary.
scanimage -L
device `epson:libusb:003:002' is a Epson Perfection1200 flatbed scanner
LmCogs
--------------090808010205010105020404
Content-Type: text/html; charset=us-ascii
Content-Transfer-Encoding: 7bit
<!DOCTYPE html PUBLIC "-//W3C//DTD HTML 4.01 Transitional//EN">
<html>
<head>
<meta content="text/html;charset=ISO-8859-1" http-equiv="Content-Type">
<title></title>
</head>
<body>
<meta content="text/html;charset=ISO-8859-1" http-equiv="Content-Type">
<title></title>
Hi I have installed the kernel 2.6.1-rc1 over Suse 9 and have as far as
I know installed most usb drivers as modules except the scanner.o
module since it is obsolete and I wanted to use libusb. I have an
epson perfection 1200 photo scanner but I can not get it to work
properly. It initialises but then crashes and then scanimage -L does
not recognise it. Xsane also does the same. Below are some of the
programs I use and some config files including sane, xsane, fstab,
dmesg etc. Appreciate some help. Thanks<br>
<br>
<br>
rpm -q sane<br>
sane-1.0.10-243<br>
<br>
rpm -q xsane<br>
xsane-0.91-135<br>
<br>
rpm -q hotplug<br>
hotplug-2002_08_26-85<br>
<br>
cat /etc/fstab<br>
/dev/hdc1 / ext2
defaults 1 1<br>
/dev/hdc2 /home ext2
defaults 1 2<br>
/dev/hdc3 swap swap
pri=42 0 0<br>
devpts /dev/pts devpts
mode=0620,gid=5 0 0<br>
proc /proc proc
defaults 0 0<br>
<br>
none /proc/bus/usb usbfs defaults
0 0<br>
/dev/cdrom /media/cdrom auto
ro,noauto,user,exec 0 0<br>
/dev/dvd /media/dvd auto
ro,noauto,user,exec 0 0<br>
/dev/fd0 /media/floppy auto
noauto,user,sync 0 0<br>
/dev/sr0 /media/sr0 auto ro,noauto,user,exec 0 0<br>
/dev/sda1 /media/sda1 auto sync,noauto,user,exec 0 0<br>
<br>
cat /proc/bus/usb/devices<br>
<br>
T: Bus=04 Lev=00 Prnt=00 Port=00 Cnt=00 Dev#= 1 Spd=12 MxCh= 2<br>
B: Alloc= 0/900 us ( 0%), #Int= 0, #Iso= 0<br>
D: Ver= 1.10 Cls=09(hub ) Sub=00 Prot=00 MxPS= 8 #Cfgs= 1<br>
P: Vendor=0000 ProdID=0000 Rev= 2.06<br>
S: Manufacturer=Linux 2.6.1-rc1 uhci_hcd<br>
S: Product=UHCI Host Controller<br>
S: SerialNumber=0000:00:10.2<br>
C:* #Ifs= 1 Cfg#= 1 Atr=40 MxPwr= 0mA<br>
I: If#= 0 Alt= 0 #EPs= 1 Cls=09(hub ) Sub=00 Prot=00 Driver=hub<br>
E: Ad=81(I) Atr=03(Int.) MxPS= 2 Ivl=255ms<br>
<br>
T: Bus=04 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#= 2 Spd=12 MxCh= 0<br>
D: Ver= 1.00 Cls=07(print) Sub=01 Prot=02 MxPS=64 #Cfgs= 1<br>
P: Vendor=04b8 ProdID=0001 Rev= 1.00<br>
S: Manufacturer=EPSON<br>
S: Product=USB Printer<br>
C:* #Ifs= 1 Cfg#= 1 Atr=40 MxPwr= 2mA<br>
I: If#= 0 Alt= 0 #EPs= 2 Cls=07(print) Sub=01 Prot=02 Driver=usblp<br>
E: Ad=01(O) Atr=02(Bulk) MxPS= 64 Ivl=0ms<br>
E: Ad=82(I) Atr=02(Bulk) MxPS= 64 Ivl=0ms<br>
<br>
T: Bus=03 Lev=00 Prnt=00 Port=00 Cnt=00 Dev#= 1 Spd=12 MxCh= 2<br>
B: Alloc= 0/900 us ( 0%), #Int= 0, #Iso= 0<br>
D: Ver= 1.10 Cls=09(hub ) Sub=00 Prot=00 MxPS= 8 #Cfgs= 1<br>
P: Vendor=0000 ProdID=0000 Rev= 2.06<br>
S: Manufacturer=Linux 2.6.1-rc1 uhci_hcd<br>
S: Product=UHCI Host Controller<br>
S: SerialNumber=0000:00:10.1<br>
C:* #Ifs= 1 Cfg#= 1 Atr=40 MxPwr= 0mA<br>
I: If#= 0 Alt= 0 #EPs= 1 Cls=09(hub ) Sub=00 Prot=00 Driver=hub<br>
E: Ad=81(I) Atr=03(Int.) MxPS= 2 Ivl=255ms<br>
<br>
T: Bus=03 Lev=01 Prnt=01 Port=01 Cnt=01 Dev#= 2 Spd=12 MxCh= 0<br>
D: Ver= 1.00 Cls=ff(vend.) Sub=ff Prot=ff MxPS=64 #Cfgs= 1<br>
P: Vendor=04b8 ProdID=0104 Rev= 1.03<br>
S: Manufacturer=EPSON<br>
S: Product=Perfection1200<br>
C:* #Ifs= 1 Cfg#= 1 Atr=40 MxPwr= 2mA<br>
I: If#= 0 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=(none)<br>
E: Ad=81(I) Atr=02(Bulk) MxPS= 64 Ivl=0ms<br>
E: Ad=02(O) Atr=02(Bulk) MxPS= 64 Ivl=0ms<br>
<br>
T: Bus=02 Lev=00 Prnt=00 Port=00 Cnt=00 Dev#= 1 Spd=12 MxCh= 2<br>
B: Alloc= 0/900 us ( 0%), #Int= 0, #Iso= 0<br>
D: Ver= 1.10 Cls=09(hub ) Sub=00 Prot=00 MxPS= 8 #Cfgs= 1<br>
P: Vendor=0000 ProdID=0000 Rev= 2.06<br>
S: Manufacturer=Linux 2.6.1-rc1 uhci_hcd<br>
S: Product=UHCI Host Controller<br>
S: SerialNumber=0000:00:10.0<br>
C:* #Ifs= 1 Cfg#= 1 Atr=40 MxPwr= 0mA<br>
I: If#= 0 Alt= 0 #EPs= 1 Cls=09(hub ) Sub=00 Prot=00 Driver=hub<br>
E: Ad=81(I) Atr=03(Int.) MxPS= 2 Ivl=255ms<br>
<br>
T: Bus=01 Lev=00 Prnt=00 Port=00 Cnt=00 Dev#= 1 Spd=480 MxCh= 6<br>
B: Alloc= 0/800 us ( 0%), #Int= 0, #Iso= 0<br>
D: Ver= 2.00 Cls=09(hub ) Sub=00 Prot=01 MxPS= 8 #Cfgs= 1<br>
P: Vendor=0000 ProdID=0000 Rev= 2.06<br>
S: Manufacturer=Linux 2.6.1-rc1 ehci_hcd<br>
S: Product=EHCI Host Controller<br>
S: SerialNumber=0000:00:10.3<br>
C:* #Ifs= 1 Cfg#= 1 Atr=40 MxPwr= 0mA<br>
I: If#= 0 Alt= 0 #EPs= 1 Cls=09(hub ) Sub=00 Prot=00 Driver=hub<br>
E: Ad=81(I) Atr=03(Int.) MxPS= 2 Ivl=256ms<br>
<br>
T: Bus=01 Lev=01 Prnt=01 Port=01 Cnt=01 Dev#= 2 Spd=480 MxCh= 0<br>
D: Ver= 2.00 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs= 1<br>
P: Vendor=0d49 ProdID=3005 Rev= 1.00<br>
S: Manufacturer=Maxtor<br>
S: Product=3000LS v01.00.00<br>
S: SerialNumber=DEF10647FBB9<br>
C:* #Ifs= 1 Cfg#= 1 Atr=c0 MxPwr= 0mA<br>
I: If#= 0 Alt= 0 #EPs= 2 Cls=08(stor.) Sub=06 Prot=50
Driver=usb-storage<br>
E: Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms<br>
E: Ad=88(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms<br>
<br>
<br>
sane-find-scanner<br>
<br>
# No SCSI scanners found. If you expected something different, make
sure that<br>
# you have loaded a SCSI driver for your SCSI adapter.<br>
<br>
found USB scanner (vendor=0x04b8, product=0x0104) at libusb:003:002<br>
# Your USB scanner was (probably) detected. It may or may not be
supported by<br>
# SANE. Try scanimage -L and read the backend's manpage.<br>
<br>
# Scanners connected to the parallel port or other proprietary ports
can't be<br>
# detected by this program.<br>
<br>
# You may want to run this program as root to find all devices. Once
you<br>
# found the scanner devices, be sure to adjust access permissions as<br>
# necessary.<br>
<br>
<br>
scanimage -L<br>
device `epson:libusb:003:002' is a Epson Perfection1200 flatbed scanner<br>
<br>
LmCogs<br>
</body>
</html>
--------------090808010205010105020404--