[sane-devel] Installingproblem with parallellportscanner and Sane.

Sun, 27 Feb 2005 13:45:35 +0100

Ok, here is the output :

[root] # SANE_DEBUG_SANEI_PA4S2=128 scanimage -L
[sanei_debug] Setting debug level of sanei_pa4s2 to 128.
[sanei_pa4s2] sanei_pa4s2_devices: interface called for the first time
[sanei_pa4s2] sanei_pa4s2_devices: invoked
[sanei_pa4s2] pa4s2_init: static int first_time = 1
[sanei_pa4s2] pa4s2_init: called for the first time
[sanei_pa4s2] pa4s2_init: initializing libieee1284
[sanei_pa4s2] pa4s2_init: 1 ports reported by IEEE 1284 library
[sanei_pa4s2] pa4s2_init: port 0 is `parport0`
[sanei_pa4s2] pa4s2_init: allocating port list
[sanei_pa4s2] pa4s2_init: initialized successfully
[sanei_pa4s2] sanei_pa4s2_open: called for device 'parport0'
[sanei_pa4s2] sanei_pa4s2_open: trying to connect to port
[sanei_pa4s2] pa4s2_open: trying to attach dev `parport0`
[sanei_pa4s2] pa4s2_init: static int first_time = 0
[sanei_pa4s2] pa4s2_init: sanei already initalized
[sanei_pa4s2] pa4s2_open: looking up port in list
[sanei_pa4s2] pa4s2_open: port is in list at port[0]
[sanei_pa4s2] pa4s2_open: setting up port data
[sanei_pa4s2] pa4s2_open: name=parport0 in_use=SANE_TRUE
[sanei_pa4s2] pa4s2_open: enabled=SANE_FALSE mode=PA4S2_MODE_NIB
[sanei_pa4s2] pa4s2_open: opening device
[sanei_pa4s2] pa4s2_open: device `parport0` opened...
[sanei_pa4s2] pa4s2_open: returning SANE_STATUS_GOOD
[sanei_pa4s2] pa4s2_open: open dev `parport0` as fd 0
[sanei_pa4s2] sanei_pa4s2_open: connected to device using fd 0
[sanei_pa4s2] sanei_pa4s2_open: checking for scanner
[sanei_pa4s2] sanei_pa4s2_enable: called for fd 0 with value 1
[sanei_pa4s2] sanei_pa4s2_enable: enable port 'parport0'
[sanei_pa4s2] pa4s2_enable: prelock[] = {0x04, 0xdf, 0x0c}
[sanei_pa4s2] sanei_pa4s2_enable: returning SANE_STATUS_GOOD
[sanei_pa4s2] sanei_pa4s2_open: reading ASIC id
[sanei_pa4s2] sanei_pa4s2_readbegin: called for fd 0 and register 0
[sanei_pa4s2] sanei_pa4s2_readbegin: NIB readbegin
[sanei_pa4s2] pa4s2_readbegin_nib: selecting register 0 at 'parport0'
[sanei_pa4s2] sanei_pa4s2_readbegin: returning SANE_STATUS_GOOD
[sanei_pa4s2] sanei_pa4s2_readbyte: called with fd 0
[sanei_pa4s2] sanei_pa4s2_readbyte: we hope, the backend called
[sanei_pa4s2] sanei_pa4s2_readbyte: readbegin, so the port is ok...
[sanei_pa4s2] sanei_pa4s2_readbyte: this means, I did not check it - it's
[sanei_pa4s2] sanei_pa4s2_readbyte: not my fault, if your PC burns down.
[sanei_pa4s2] sanei_pa4s2_readbyte: read in NIB mode
[sanei_pa4s2] pa4s2_readbyte_nib: reading value 0xa8 from 'parport0'
[sanei_pa4s2] sanei_pa4s2_readbyte: read finished
[sanei_pa4s2] sanei_pa4s2_readbyte: got value 0xa8
[sanei_pa4s2] sanei_pa4s2_readbyte: returning SANE_STATUS_GOOD
[sanei_pa4s2] sanei_pa4s2_readend: called for fd 0
[sanei_pa4s2] sanei_pa4s2_readend: we hope, the backend called
[sanei_pa4s2] sanei_pa4s2_readend: readbegin, so the port is ok...
[sanei_pa4s2] sanei_pa4s2_readend: this means, I did not check it - it's
[sanei_pa4s2] sanei_pa4s2_readend: not my fault, if your PC burns down.
[sanei_pa4s2] sanei_pa4s2_readend: NIB mode readend
[sanei_pa4s2] pa4s2_readend_nib: end of reading sequence for fd 0
[sanei_pa4s2] sanei_pa4s2_readend: returning SANE_STATUS_GOOD
[sanei_pa4s2] sanei_pa4s2_open: detected ASIC id 1013
[sanei_pa4s2] sanei_pa4s2_enable: called for fd 0 with value 0
[sanei_pa4s2] sanei_pa4s2_enable: disable port 'parport0'
[sanei_pa4s2] pa4s2_disable: state restored
[sanei_pa4s2] sanei_pa4s2_enable: returning SANE_STATUS_GOOD
[sanei_pa4s2] sanei_pa4s2_open: trying better modes
[sanei_pa4s2] sanei_pa4s2_open: trying mode 0
[sanei_pa4s2] sanei_pa4s2_enable: called for fd 0 with value 1
[sanei_pa4s2] sanei_pa4s2_enable: enable port 'parport0'
[sanei_pa4s2] pa4s2_enable: prelock[] = {0x04, 0xdf, 0x0c}
[sanei_pa4s2] sanei_pa4s2_enable: returning SANE_STATUS_GOOD
[sanei_pa4s2] sanei_pa4s2_readbegin: called for fd 0 and register 0
[sanei_pa4s2] sanei_pa4s2_readbegin: NIB readbegin
[sanei_pa4s2] pa4s2_readbegin_nib: selecting register 0 at 'parport0'
[sanei_pa4s2] sanei_pa4s2_readbegin: returning SANE_STATUS_GOOD
[sanei_pa4s2] sanei_pa4s2_readbyte: called with fd 0
[sanei_pa4s2] sanei_pa4s2_readbyte: we hope, the backend called
[sanei_pa4s2] sanei_pa4s2_readbyte: readbegin, so the port is ok...
[sanei_pa4s2] sanei_pa4s2_readbyte: this means, I did not check it - it's
[sanei_pa4s2] sanei_pa4s2_readbyte: not my fault, if your PC burns down.
[sanei_pa4s2] sanei_pa4s2_readbyte: read in NIB mode
[sanei_pa4s2] pa4s2_readbyte_nib: reading value 0xa8 from 'parport0'
[sanei_pa4s2] sanei_pa4s2_readbyte: read finished
[sanei_pa4s2] sanei_pa4s2_readbyte: got value 0xa8
[sanei_pa4s2] sanei_pa4s2_readbyte: returning SANE_STATUS_GOOD
[sanei_pa4s2] sanei_pa4s2_readend: called for fd 0
[sanei_pa4s2] sanei_pa4s2_readend: we hope, the backend called
[sanei_pa4s2] sanei_pa4s2_readend: readbegin, so the port is ok...
[sanei_pa4s2] sanei_pa4s2_readend: this means, I did not check it - it's
[sanei_pa4s2] sanei_pa4s2_readend: not my fault, if your PC burns down.
[sanei_pa4s2] sanei_pa4s2_readend: NIB mode readend
[sanei_pa4s2] pa4s2_readend_nib: end of reading sequence for fd 0
[sanei_pa4s2] sanei_pa4s2_readend: returning SANE_STATUS_GOOD
[sanei_pa4s2] sanei_pa4s2_enable: called for fd 0 with value 0
[sanei_pa4s2] sanei_pa4s2_enable: disable port 'parport0'
[sanei_pa4s2] pa4s2_disable: state restored
[sanei_pa4s2] sanei_pa4s2_enable: returning SANE_STATUS_GOOD
[sanei_pa4s2] sanei_pa4s2_open: mode works
[sanei_pa4s2] sanei_pa4s2_open: skipping mode UNI
[sanei_pa4s2] sanei_pa4s2_open: trying mode 2
[sanei_pa4s2] sanei_pa4s2_enable: called for fd 0 with value 1
[sanei_pa4s2] sanei_pa4s2_enable: enable port 'parport0'
[sanei_pa4s2] pa4s2_enable: prelock[] = {0x04, 0xdf, 0x0c}
[sanei_pa4s2] sanei_pa4s2_enable: returning SANE_STATUS_GOOD
[sanei_pa4s2] sanei_pa4s2_readbegin: called for fd 0 and register 0
[sanei_pa4s2] sanei_pa4s2_readbegin: EPP readbegin
[sanei_pa4s2] pa4s2_readbegin_epp: selecting register 0 at 'parport0'
[sanei_pa4s2] sanei_pa4s2_readbegin: returning SANE_STATUS_GOOD
[sanei_pa4s2] sanei_pa4s2_readbyte: called with fd 0
[sanei_pa4s2] sanei_pa4s2_readbyte: we hope, the backend called
[sanei_pa4s2] sanei_pa4s2_readbyte: readbegin, so the port is ok...
[sanei_pa4s2] sanei_pa4s2_readbyte: this means, I did not check it - it's
[sanei_pa4s2] sanei_pa4s2_readbyte: not my fault, if your PC burns down.
[sanei_pa4s2] sanei_pa4s2_readbyte: read in EPP mode
[sanei_pa4s2] pa4s2_readbyte_epp: reading value 0xa8 from 'parport0'
[sanei_pa4s2] sanei_pa4s2_readbyte: read finished
[sanei_pa4s2] sanei_pa4s2_readbyte: got value 0xa8
[sanei_pa4s2] sanei_pa4s2_readbyte: returning SANE_STATUS_GOOD
[sanei_pa4s2] sanei_pa4s2_readend: called for fd 0
[sanei_pa4s2] sanei_pa4s2_readend: we hope, the backend called
[sanei_pa4s2] sanei_pa4s2_readend: readbegin, so the port is ok...
[sanei_pa4s2] sanei_pa4s2_readend: this means, I did not check it - it's
[sanei_pa4s2] sanei_pa4s2_readend: not my fault, if your PC burns down.
[sanei_pa4s2] sanei_pa4s2_readend: EPP mode readend
[sanei_pa4s2] pa4s2_readend_epp: end of reading sequence
[sanei_pa4s2] sanei_pa4s2_readend: returning SANE_STATUS_GOOD
[sanei_pa4s2] sanei_pa4s2_enable: called for fd 0 with value 0
[sanei_pa4s2] sanei_pa4s2_enable: disable port 'parport0'
[sanei_pa4s2] pa4s2_disable: state restored
[sanei_pa4s2] sanei_pa4s2_enable: returning SANE_STATUS_GOOD
[sanei_pa4s2] sanei_pa4s2_open: mode works
[sanei_pa4s2] sanei_pa4s2_open: using mode 2
[sanei_pa4s2] sanei_pa4s2_open: returning SANE_STATUS_GOOD
[sanei_pa4s2] sanei_pa4s2_enable: called for fd 0 with value 1
[sanei_pa4s2] sanei_pa4s2_enable: enable port 'parport0'
[sanei_pa4s2] pa4s2_enable: prelock[] = {0xff, 0x8f, 0x0c}
[sanei_pa4s2] sanei_pa4s2_enable: returning SANE_STATUS_GOOD
[sanei_pa4s2] sanei_pa4s2_readbegin: called for fd 0 and register 0
[sanei_pa4s2] sanei_pa4s2_readbegin: EPP readbegin
[sanei_pa4s2] pa4s2_readbegin_epp: selecting register 0 at 'parport0'
[sanei_pa4s2] sanei_pa4s2_readbegin: returning SANE_STATUS_GOOD
[sanei_pa4s2] sanei_pa4s2_readbyte: called with fd 0
[sanei_pa4s2] sanei_pa4s2_readbyte: we hope, the backend called
[sanei_pa4s2] sanei_pa4s2_readbyte: readbegin, so the port is ok...
[sanei_pa4s2] sanei_pa4s2_readbyte: this means, I did not check it - it's
[sanei_pa4s2] sanei_pa4s2_readbyte: not my fault, if your PC burns down.
[sanei_pa4s2] sanei_pa4s2_readbyte: read in EPP mode
Here it freezes, nothing happens ......
Sincerely,
Philip Moller
Sweden.

Jochen Eisinger wrote:
> Hi,
> 
> could you please send the output of
> 
> SANE_DEBUG_SANEI_PA4S2=128 scanimage -L
> 
> kind regards
> -- jochen> 
> 
 > Philip Moller wrote:
> Hi !
> 
> I have major problem installing my parallellscanner with Sane.
> And I don't want to get a new scanner, because it isn't anything wrong with the old one.
> 
> I have downloaded the latest tarball "sane-backends-1.0.15.tar.gz" at ftp://ftp.sane-project.org/pub/sane/sane-backends-1.0.15/,
> decompressed the tarball (tar -xvzf sane-backends-1.0.15.tar.gz) and I compiled and installed (./configure, make, make install) sane-backends-1.0.15.
> 
> My parallelportscanner is old, but it works fine i Windows98 with
> TWAIN, so there is no problem with the scanner's functionality and the
> connection with the computer.
> My printer Canon S750, that is connected at the same parallelport as the
> scanner, is working fine in Linux.
> My printer S750 is connected to the scanner and the scanner is
> connected to the parallelport in the computer.
> The PRINTER works fine in Linux and in Windows98 the scanner+printer
> works fine too.
> The only problem is the scanner, that wont work at all for me in Linux ?
> 
> My computer data :
> i686 Pentium III (Coppermine), RAM 128MB, HDD 9GB.
> Linux version: Fedora Core 3 (2.6.10-1.766_FC3) (gcc version 3.4.2 20041017 (Red Hat 3.4.2-6.fc3))
> My scanner data :
> Mustek Plug&Scan 600 III EP Plus
> 300 DPI, CCD(101x/0x), EPP, ASICID:1013/1015, CCDTYPE: 00/01
> 
> I have printed out and read the documentation on http://penguin-breeder.org/sane/mustek_pp/
> and followed the instruction, step by step.
> 
> When I print "sane-find-scanner -p" in the console, I get this:
> 
> [root] # sane-find-scanner -p
> found possible Mustek parallel port scanner at "parport0"
> 
> So, "sane-find-scanner" detects my scanner...
> 
> But when I print "SANE_DEBUG_MUSTEK_PP=1 scanimage -L", I get this:
> 
> [root] # SANE_DEBUG_MUSTEK_PP=1 scanimage -L
> [sanei_debug] Setting debug level of mustek_pp to 1.
> 
> I am waiting !!!
> Here it freezes, nothing happends ....
> 
> I have enabled the mustek_pp backend in my dll.conf, with removal of the # sign in front of it.
> 
> I have also adjusted the mustek_pp.conf file to reflect my hardware setup (scanner mustek-ccd300 * ccd300).
> 
> So my config files are ok.
> 
> I don't have a second installation of sane (with its own config files), so that isn't the problem.
> 
> Please, I could use some expert advice...
> 
> What can I do, to get the scanner working with Sane ?
> 
> Is there some tweak I have to do, when I use Fedora 3 with sane-backends-1.0.15 ?
> 
> Sincerely,
> Philip Moller
> Sweden.