[sane-devel] options for epson perfection V100 PHOTO?

[David Roundy]

On Thu, Jan 11, 2007 at 01:13:22PM +0100, Alessandro Zummo wrote:
> David Roundy <droundy at darcs.net> wrote:
> > Sad to say, I've made the mistake of purchasing an epson perfection V100
> > photo scanner, and am now wondering what I can do with this thing.  I see
> > now that it's not supported, although there's a proprietary iscan thing
> > that works with it, but it doesn't seem to be available for x86-64.
> 
>  Hello David,

Hello!

>   we should first understand if this scanner uses the 
>  EPSON ESC/I protocol. You might want to enable debugging
>  (man sane-epson) and report the results of scanimage -L .

I'm attaching the output.  I went with full debugging, since you didn't
specify, and I'm not sure what you'd need.  Thanks for your help!
-- 
David Roundy
Department of Physics
Oregon State University
-------------- next part --------------
[sanei_debug] Setting debug level of epson to 128.
[epson] sane_init: sane-backends 1.0.18
[epson] sane_init, ># epson.conf<
[epson] sane_init, >#<
[epson] sane_init, ># here are some examples for how to configure the EPSON backend<
[epson] sane_init, >#<
[epson] sane_init, ># SCSI scanner:<
[epson] sane_init, >scsi EPSON<
[epson] sane_init, ># for the GT-6500:<
[epson] sane_init, >scsi "EPSON SC"<
[epson] sane_init, >#<
[epson] sane_init, ># Parallel port scanner:<
[epson] sane_init, >#pio 0x278<
[epson] sane_init, >#pio 0x378<
[epson] sane_init, >#pio 0x3BC<
[epson] sane_init, >#<
[epson] sane_init, ># USB scanner:<
[epson] sane_init, ># There are two different methods of configuring a USB scanner: libusb and the kernel module<
[epson] sane_init, ># For any system with libusb support (which is pretty much any recent Linux distribution) the<
[epson] sane_init, ># following line is sufficient. This however assumes that the connected scanner (or to be more<
[epson] sane_init, ># accurate, it's device ID) is known to the backend.<
[epson] sane_init, >usb 0x4b8 0x12d<
[epson] attach_one_usb(libusb:003:033)
[epson] SANE Epson Backend v0.2.46 - 2006-06-11
[epson] attach(libusb:003:033, 3)
[epson] attach: opening libusb:003:033
[epson] Found valid EPSON scanner: 0x4b8/0x12d (vendorID/productID)
[epson] reset()
[epson] send buf, size = 2
[epson] buf[0] 1b .
[epson] buf[1] 40 @
[epson] w_cmd_count = 1
[epson] r_cmd_count = 0
[epson] w_cmd_count = 1
[epson] r_cmd_count = 1
[epson] receive buf, expected = 1, got = 1
[epson] buf[0] 15 .
[epson] get_identity_information()
[epson] send buf, size = 2
[epson] buf[0] 1b .
[epson] buf[1] 49 I
[epson] w_cmd_count = 2
[epson] r_cmd_count = 1
[epson] w_cmd_count = 2
[epson] r_cmd_count = 2
[epson] receive buf, expected = 4, got = 1
[epson] buf[0] 15 .
[epson] code   15
[epson] type      0x00
[epson] level     0x00
[epson] no option equipment installed
[epson] Unknown type   or level  , using B3
[epson] fbf tlx 0.000000 tly 0.000000 brx -32768.000000 bry -32768.000000 [mm]
[epson] send buf, size = 2
[epson] buf[0] 1b .
[epson] buf[1] 44 D
[epson] w_cmd_count = 3
[epson] r_cmd_count = 2
[epson] w_cmd_count = 3
[epson] r_cmd_count = 3
[epson] receive buf, expected = 1, got = 1
[epson] buf[0] 15 .
[epson] send buf, size = 2
[epson] buf[0] 1b .
[epson] buf[1] 44 D
[epson] w_cmd_count = 4
[epson] r_cmd_count = 3
[epson] w_cmd_count = 4
[epson] r_cmd_count = 4
[epson] receive buf, expected = 1, got = 1
[epson] buf[0] 15 .
[epson] send buf, size = 2
[epson] buf[0] 1b .
[epson] buf[1] 44 D
[epson] w_cmd_count = 5
[epson] r_cmd_count = 4
[epson] w_cmd_count = 5
[epson] r_cmd_count = 5
[epson] receive buf, expected = 1, got = 1
[epson] buf[0] 15 .
[epson] Max. supported color depth = 8
[epson] request_focus_position()
[epson] Disabling 'Set Focus' support
[epson] send buf, size = 2
[epson] buf[0] 1b .
[epson] buf[1] 66 f
[epson] w_cmd_count = 6
[epson] r_cmd_count = 5
[epson] w_cmd_count = 6
[epson] r_cmd_count = 6
[epson] receive buf, expected = 4, got = 1
[epson] buf[0] 15 .
[epson] code   15
[epson] scanner model: 
[epson] close_scanner(fd = 0)
[epson] w_cmd_count = 6
[epson] r_cmd_count = 6
[epson] w_cmd_count = 6
[epson] r_cmd_count = 6
[epson] sane_init, ># For libusb support for unknown scanners use the following command<
[epson] sane_init, ># usb <product ID> <device ID><
[epson] sane_init, ># e.g.:<
[epson] sane_init, ># usb 0x4b8 0x110<
[epson] sane_init, ># And for the scanner module, use the following configuration:<
[epson] sane_init, >#usb /dev/usbscanner0<
[epson] sane_init, >#usb /dev/usb/scanner0<
[epson] sane_get_devices()
device `epson:libusb:003:033' is a Epson  flatbed scanner