[sane-devel] Help with canon FS2710 on Mac OSX Tiger/G4

[Kirk Becnel]

I think there is some sort of initialization ritual that must be done prior to use. 

Here is the output you requested:

john-does-power-mac-g4:/usr/local/bin becnel$ SANE_DEBUG_CANON=255 ./scanimage -L
[sanei_debug] Setting debug level of canon to 255.
[canon] >> sane_init
[canon] sane_init: sane-backends 1.0.21cvs
[canon] >> attach_one
[canon] >> attach
[canon] attach: opening <01851f000000001736ab60d8>
[canon] attach: sending (standard) INQUIRY
[canon] >> inquiry
[canon] << inquiry
[canon] attach: sending TEST_UNIT_READY
[canon] >> test_unit_ready
[canon] << test_unit_ready
[canon] attach: test unit ready failed (Error during device I/O)
[canon] << attach_one
[canon] << sane_init
[canon] >> sane_get_devices
[canon] << sane_get_devices

No scanners were identified. If you were expecting something different,
check that the scanner is plugged in, turned on and detected by the
sane-find-scanner tool (if appropriate). Please read the documentation
which came with this software (README, FAQ, manpages).
[canon] >> sane_exit
[canon] << sane_exit
john-does-power-mac-g4:/usr/local/bin becnel$ 


----- Original Message ----
From: m. allan noah <kitno455 at gmail.com>
To: Kirk Becnel <kirkbecnel at yahoo.com>
Cc: sane-devel at lists.alioth.debian.org
Sent: Thu, May 6, 2010 12:22:19 PM
Subject: Re: [sane-devel] Help with canon FS2710 on Mac OSX Tiger/G4

Does image capture have the device open somehow?

what is the output of this command:

SANE_DEBUG_CANON=255 scanimage -L

allan

On Thu, May 6, 2010 at 11:54 AM, Kirk Becnel <kirkbecnel at yahoo.com> wrote:
> I cannot get sane to work, except once, then when I used image capture, it stopped working and did not work again.
>
> It is found
> john-does-power-mac-g4:/usr/local/bin becnel$ ./sane-find-scanner -q
> found SCSI scanner "CANON IX-27025E 1.13" at <01851f000000001736ab60d8>
>
> But when I run scanimage:
>
> john-does-power-mac-g4:/usr/local/bin becnel$ ./scanimage -T
> scanimage: no SANE devices found
>
> Here is my config for it:
> john-does-power-mac-g4:/usr/local/etc/sane.d becnel$ cat canon.conf
> #canon.conf
> scsi CANON * Scanner
> #/dev/sg0
>
>
> john-does-power-mac-g4:/usr/local/bin becnel$ ./scanimage -L
>
> No scanners were identified. If you were expecting something different,
> check that the scanner is plugged in, turned on and detected by the
> sane-find-scanner tool (if appropriate). Please read the documentation
> which came with this software (README, FAQ, manpages).
> john-does-power-mac-g4:/usr/local/bin becnel$ ./scanimage -v
> scanimage: no SANE devices found
> john-does-power-mac-g4:/usr/local/bin becnel$
>
> I was able to get scans to work with vuescan and silverfast, but for what I am doing would rather use sane.
>
>
>
>
>
>
> --
> sane-devel mailing list: sane-devel at lists.alioth.debian.org
> http://lists.alioth.debian.org/mailman/listinfo/sane-devel
> Unsubscribe: Send mail with subject "unsubscribe your_password"
>             to sane-devel-request at lists.alioth.debian.org
>



-- 
"The truth is an offense, but not a sin"