[sane-devel] LIDE 60. configure scanning prefs?
Ben Green
greenb1 at mac.com
Fri Feb 11 19:49:36 UTC 2011
Ha ha - thanks Allan - it worked.. and i pulled up the options too..
HOWEVER - my (ongoing) problem is that i need to switch off the calibration section of the scan process so that i receive a raw data feed.
Is there further settings I can effect? For example in the plustec backend, I was able to adjust crop area, gain, calibration on/off etc.. is this just not an option with genesys? Is there someone who can do such things? (certainly I can't - i couldn't even get the command into terminal!!)
Thanks
Ben
On 11 Feb 2011, at 19:38, m. allan noah wrote:
> It is a command. you run it in the terminal. If you got no text back,
> try running this instead:
>
> scanimage -L
>
> allan
>
> On Fri, Feb 11, 2011 at 2:33 PM, Ben Green <greenb1 at mac.com> wrote:
>>
>>
>> On 10 Feb 2011, at 05:24, stef wrote:
>>
>>> Le Wednesday 09 February 2011 18:01:08 Ben Green, vous avez écrit :
>>>> Hi
>>>> I'm trying to configure various actions inside my Lide 60 such as
>>>> analogue gain, tinkering with the calibration and the crop area that
>>>> it scans with.
>>>>
>>>> The backend seems to have been abandoned on the support front -
>>>> scanning is no problem, worked first time - its just this .conf file
>>>> that i cannot drive? is there a list of commands I can feed into
>>>> the .config file? like lamp on/off, red gain +3 ??? i'm afraid i dont
>>>> speak Genesys?
>>>>
>>>> I have done this with some earlier LIDEs that worked with the plustec
>>>> backend - these were quite straightforward - i could open the SANE
>>>> prefs and turn calibration on/off, change gain and crop just by
>>>> changing some zeros and ones.. however this genesys backend has only a
>>>> list of scanners and their model/product addresses - I don't know what
>>>> commands to put into the .conf file.
>>>>
>>>> I'm using SANE: mac10.6:
>>>>
>>>> TWAIN SANE Interface 2.9 binary http://www.ellert.se/twain-sane/
>>>> SANE Preference Pane 0.9 binary http://www.ellert.se/twain-sane/ SANE
>>>> backends http://www.sane-project.org/ libusb 0.1.13 beta 2009-09-10
>>>> binary http://libusb.sourceforge.net/
>>>>
>>>>
>>>> Any Help is Much Appreciated..
>>>>
>>>>
>>>> Thnaks
>>>>
>>>>
>>>> Ben
>>>
>>> Hello,
>>>
>>> all user settable settings are published by the backend through options.
>>> You can get the full list of active options for your model with 'scanimage -d
>>> genesys --help'. There is no options or settings to modify in the conf file.
>>>
>>> Regards,
>>> Stef
>>>
>>> --
>>> sane-devel mailing list: sane-devel at lists.alioth.debian.org
>>> http://lists.alioth.debian.org/mailman/listinfo/sane-devel
>>> Unsubscribe: Send mail with subject "unsubscribe your_password"
>>> to sane-devel-request at lists.alioth.debian.org
>>
>>
>> Hi Steph,
>>
>> Could you tell me how and where I use this command? (scanimage -d genesys --help)
>> Is it in the SANE prefs file? if so, do i enter the command under my particular scanner model?
>> I tried putting this command into terminal but got nothing back -
>>
>> Sorry I cant profess to know much about command line interface..
>>
>>
>> Thanks for you help..
>>
>>
>> Ben
>>
>>
>>
>> --
>> sane-devel mailing list: sane-devel at lists.alioth.debian.org
>> http://lists.alioth.debian.org/mailman/listinfo/sane-devel
>> Unsubscribe: Send mail with subject "unsubscribe your_password"
>> to sane-devel-request at lists.alioth.debian.org
>>
>
>
>
> --
> "The truth is an offense, but not a sin"
More information about the sane-devel
mailing list