[sane-devel] scanbd Canon MG6250

[Matthias Thon]

Hi Rolf,

now hopefully the right debug information. Now after starting scanimage -A
, it waits for the button information. I try different buttons (black,
color) Changed before from JPEG to PDF or TIFF but scanimage waits till
timeout. See the output.

regards Matthias


root at matze-Satellite-C660:/usr/local/src/sane-backends-git/sane-backends#
scanimage -V
scanimage (sane-backends) 1.0.24git; backend version 1.0.24
root at matze-Satellite-C660:/usr/local/src/sane-backends-git/sane-backends#
scanimage -A
[sanei_debug] Setting debug level of pixma to 7.
[pixma] pixma is compiled without pthread support.
[pixma] pixma version 0.17.0
[pixma] pixma_collect_devices() found Canon PIXMA MG6200 at libusb:002:005
[pixma] sanei_bjnp_find_devices:
[pixma] eth0 is IPv4 capable, sending broadcast, socket = 3
[pixma] wlan0 is IPv4 capable, sending broadcast, socket = 4
[pixma] eth0 is IPv6 capable, sending broadcast, socket = 5
[pixma] wlan0 is IPv6 capable, sending broadcast, socket = 6
[pixma] pixma_find_scanners() found 1 devices
[pixma] pixma_collect_devices() found Canon PIXMA MG6200 at libusb:002:005
[pixma] sanei_bjnp_find_devices:
[pixma] eth0 is IPv4 capable, sending broadcast, socket = 3
[pixma] wlan0 is IPv4 capable, sending broadcast, socket = 4
[pixma] eth0 is IPv6 capable, sending broadcast, socket = 5
[pixma] wlan0 is IPv6 capable, sending broadcast, socket = 6
[pixma] pixma_open(): Canon PIXMA MG6200

All options specific to device `pixma:04A91755_14B4F6':
  Scan mode:
    --resolution auto||75|150|300|600|1200|2400|4800dpi [75]
        Sets the resolution of the scanned image.
    --mode auto|Color|Gray|Lineart [Color]
        Selects the scan mode (e.g., lineart, monochrome, or color).
    --source Flatbed [Flatbed]
        Selects the scan source (such as a document-feeder). Set source
before
        mode and resolution. Resets mode and resolution to auto values.
    --button-controlled[=(yes|no)] [no]
        When enabled, scan process will not start immediately. To proceed,
        press "SCAN" button (for MP150) or "COLOR" button (for other
models).
        To cancel, press "GRAY" button.
  Gamma:
    --custom-gamma[=(auto|yes|no)] [yes]
        Determines whether a builtin or a custom gamma-table should be used.
    --gamma-table auto|0..255,...
        Gamma-correction table.  In color mode this option equally affects
the
        red, green, and blue channels simultaneously (i.e., it is an
intensity
        gamma table).
    --gamma auto|0.299988..5 [2.2]
        Changes intensity of midtones
  Geometry:
    -l auto|0..216.069mm [0]
        Top-left x position of scan area.
    -t auto|0..297.011mm [0]
        Top-left y position of scan area.
    -x auto|0..216.069mm [216.069]
        Width of scan-area.
    -y auto|0..297.011mm [297.011]
        Height of scan-area.
  Buttons:
    --button-update
        Update button state
[pixma] Sending time: '13/02/05 18:12'
[pixma] No response yet. Timed out in 8 sec.
[pixma] No response yet. Timed out in 7 sec.
[pixma] No response yet. Timed out in 6 sec.
[pixma] No response yet. Timed out in 5 sec.
[pixma] No response yet. Timed out in 4 sec.
[pixma] No response yet. Timed out in 3 sec.
[pixma] No response yet. Timed out in 2 sec.
[pixma] No response yet. Timed out in 1 sec.
[pixma] WARNING: Error in response phase. cmd:eb80
[pixma]   If the scanner hangs, reset it and/or unplug the USB cable.
    --button-1 <int> [0] [read-only]
        Button 1
    --button-2 <int> [0] [read-only]
        Button 2
    --original <int> [0] [read-only]
        Type of original to scan
    --target <int> [0] [read-only]
        Target operation type
  Extras:
    --threshold auto|0..100% (in steps of 1) [inactive]
        Select minimum-brightness to get a white point
    --threshold-curve auto|0..127 (in steps of 1) [inactive]
        Dynamic threshold curve, from light to dark, normally 50-65

[pixma] pixma_close(): Canon PIXMA MG6200
root at matze-Satellite-C660:/usr/local/src/sane-backends-git/sane-backends#
-------------- next part --------------
An HTML attachment was scrubbed...
URL: <http://lists.alioth.debian.org/pipermail/sane-devel/attachments/20130205/b5394710/attachment-0001.html>