[sane-devel] sane-pixma TS6150
Rolf Bensch
rolf at bensch-online.de
Thu Sep 13 17:18:55 BST 2018
Hi Giles,
As I mentioned before, very probably your scanner cannot be used via
Ethernet and WiFi. Please retry scanning via USB connection. Then you
should remove the Ethernet cable and/or disable WiFi.
Hope this helps.
Cheers,
Rolf
Am 12.09.2018 um 23:21 schrieb Giles Knap:
> Thanks Rolf,
>
> I was immediately able to see the scanner but unfortunately when I try
> to scan I get an error. I have tried power cycling the scanner and
> restarting ubuntu but get the following:-
>
> Thanks,
> giles.
> --------------------------------
> giles at gklinux:~$ SANE_DEBUG_PIXMA=21 SANE_DEBUG_BJNP=3 simple-scan
>
> (simple-scan:15292): Gtk-WARNING **: 22:19:23.217: Failed to register
> client: GDBus.Error:org.gnome.SessionManager.AlreadyRegistered: Unable
> to register client
> [sanei_debug] Setting debug level of pixma to 21.
> [pixma] pixma is compiled with pthread support.
> [pixma] pixma version 0.17.50
> [sanei_debug] Setting debug level of bjnp to 3.
> [pixma] pixma_collect_devices() found Canon PIXMA TS6100 Series at
> libusb:002:005
> [bjnp] sanei_bjnp_find_devices, pixma backend version: 0.17.50
> [bjnp] sanei_bjnp_find_devices: No devices specified in configuration file.
> [bjnp] sanei_bjnp_find_devices: Added all configured scanners, now do
> auto detection...
> [bjnp] prepare_socket: lo is not a valid IPv4 interface, skipping...
> [bjnp] prepare_socket: eno1 is IPv4 capable, sending broadcast, socket = 23
> [bjnp] prepare_socket: lo is not a valid IPv6 interface, skipping...
> [bjnp] prepare_socket: eno1 is IPv6 capable, sending broadcast, socket = 24
> [bjnp] prepare_socket: eno1 is IPv6 capable, sending broadcast, socket = 25
> [bjnp] prepare_socket: eno1 is IPv6 capable, sending broadcast, socket = 26
> [bjnp] sanei_find_devices: scanner discovery finished...
> [pixma] pixma_find_scanners() found 1 devices
> [pixma] pixma_collect_devices() found Canon PIXMA TS6100 Series at
> libusb:002:005
> [bjnp] sanei_bjnp_find_devices, pixma backend version: 0.17.50
> [bjnp] sanei_bjnp_find_devices: No devices specified in configuration file.
> [bjnp] sanei_bjnp_find_devices: Added all configured scanners, now do
> auto detection...
> [bjnp] prepare_socket: lo is not a valid IPv4 interface, skipping...
> [bjnp] prepare_socket: eno1 is IPv4 capable, sending broadcast, socket = 23
> [bjnp] prepare_socket: lo is not a valid IPv6 interface, skipping...
> [bjnp] prepare_socket: eno1 is IPv6 capable, sending broadcast, socket = 24
> [bjnp] prepare_socket: eno1 is IPv6 capable, sending broadcast, socket = 25
> [bjnp] prepare_socket: eno1 is IPv6 capable, sending broadcast, socket = 26
> [bjnp] sanei_find_devices: scanner discovery finished...
> [pixma] pixma_open(): Canon PIXMA TS6100 Series
> [pixma] pixma_connect() failed EBUSY
> [pixma] pixma_open() failed EBUSY
> [pixma] pixma_close(): Canon PIXMA TS6100 Series
>
>
> On Wed, Sep 12, 2018 at 9:14 PM Rolf Bensch <rolf at bensch-online.de
> <mailto:rolf at bensch-online.de>> wrote:
>
> Hi Giles,
>
> I just added your scanner to SANE. You can pull the recent version from
> git now.
>
> Or you can use my Ubuntu PPA:
> https://launchpad.net/~rolfbensch/+archive/ubuntu/sane-git
> <https://launchpad.net/%7Erolfbensch/+archive/ubuntu/sane-git> .
> Then you
> must wait for the next version tomorrow.
>
> Please report your results.
>
> Cheers,
> Rolf
>
> Am 12.09.2018 um 20:40 schrieb Giles Knap:
> > Many thanks, Rolf.
> >
> > I would be very happy to have my scanner working via USB.
> >
> > The USB IDs are as follows:-
> > Bus 002 Device 005: ID 04a9:1822 Canon, Inc.
> >
> > Cheers,
> > giles
> >
> > On Wed, Sep 12, 2018 at 6:41 PM Rolf Bensch <rolf at bensch-online.de
> <mailto:rolf at bensch-online.de>
> > <mailto:rolf at bensch-online.de <mailto:rolf at bensch-online.de>>> wrote:
> >
> > Hi Giles,
> >
> > I'm sorry to tell you that your scanner isn't supported by
> SANE. You
> > confuse your TS6150 with the TS6050 (PIXMA TS6000 Series).
> >
> > There's another problem with the tested TSxxxx scanners: WiFi
> isn't
> > working.
> >
> > I can quickly implement your scanner to SANE, but you very
> probably
> > need to use the scanner USB connected to your PC. Please send me
> > your scanner's USB IDs, which can be indentified on a console
> with:
> > $ lsusb
> > Bus 002 Device 007: ID 04a9:1908 Canon, Inc.
> > ...
> >
> > Hope this helps.
> >
> > Cheers,
> > Rolf
> >
> >
> > Am 03.09.2018 um 18:30 schrieb Giles Knap:
> >> Hello,
> >>
> >> I'm testing the latest pixma support against the TS6150 which is
> >> listed as not yet tested.
> >>
> >> I can't connect over USB or TCP even if I explicitly place my
> >> device's IP address in /etc/sane.d/pixma.conf as follows:-
> >>
> >> bjnp-timeout=5000
> >> bjnp://192.168.0.100:8612 <http://192.168.0.100:8612>
> <http://192.168.0.100:8612>
> >>
> >> I am running on Ubuntu 18.04.1 and have built from the latest
> >> source in master branch
> of https://gitlab.com/sane-project/backends.
> >>
> >> The compilation is with debug and I get the following output
> >> pasted below.
> >>
> >> The device is working since I am able to scan in an incredibly
> >> limited fashion using the official scangearmp2 (which I have
> since
> >> uninstalled). The device also works if I reboot to windows.
> >>
> >> ----------------------------------------------
> >> giles at gklinux:~/github/backends$ SANE_DEBUG_PIXMA=21
> >> SANE_DEBUG_BJNP=3 simple-scan
> >>
> >> (simple-scan:15264): Gtk-WARNING **: 17:10:07.715: Failed to
> >> register client:
> >> GDBus.Error:org.gnome.SessionManager.AlreadyRegistered: Unable to
> >> register client
> >> [sanei_debug] Setting debug level of pixma to 21.
> >> [pixma] pixma is compiled with pthread support.
> >> [pixma] pixma version 0.17.49
> >> [sanei_debug] Setting debug level of bjnp to 3.
> >> [bjnp] sanei_bjnp_find_devices, pixma backend version: 0.17.49
> >> [bjnp] Set new default timeout value: 5000 ms.[bjnp]
> >> sanei_bjnp_find_devices: Adding scanner from pixma.conf:
> >> bjnp://192.168.0.100:8612 <http://192.168.0.100:8612>
> <http://192.168.0.100:8612>
> >> [bjnp]
> bjnp_allocate_device(bjnp://192.168.0.100:8612/timeout=5000
> <http://192.168.0.100:8612/timeout=5000>
> >> <http://192.168.0.100:8612/timeout=5000>) 0
> >> [bjnp] get_scanner_name: Name for 192.168.0.100 not found : Name
> >> or service not known
> >> [bjnp] setup_udp_socket: Setting up a UDP socket, dest:
> >> 192.168.0.100 port 8612
> >> [bjnp] udp_command: ERROR - recv failed: Connection refused[bjnp]
> >> udp_command: ERROR - recv failed: Connection refused[bjnp]
> >> udp_command: ERROR - recv failed: Connection refused[bjnp]
> >> udp_command: ERROR - no data received (timeout = 5000)
> >> [bjnp] bjnp_init_device_structure: Cannot read mac address,
> >> skipping this scanner
> >> [bjnp] bjnp_allocate_device: Scanner not yet in our list, added
> >> it: 192.168.0.100:8612 <http://192.168.0.100:8612>
> <http://192.168.0.100:8612>
> >> [bjnp] setup_udp_socket: Setting up a UDP socket, dest:
> >> 192.168.0.100 port 8612
> >> [bjnp] udp_command: ERROR - recv failed: Connection refused[bjnp]
> >> udp_command: ERROR - recv failed: Connection refused[bjnp]
> >> udp_command: ERROR - recv failed: Connection refused[bjnp]
> >> udp_command: ERROR - no data received (timeout = 5000)
> >> [bjnp] get_scanner_id: ERROR - Failed to retrieve scanner
> identity:
> >> [bjnp] add_scanner: ERROR - Cannot read scanner make & model:
> >> bjnp://192.168.0.100:8612/timeout=5000
> <http://192.168.0.100:8612/timeout=5000>
> >> <http://192.168.0.100:8612/timeout=5000>
> >> [bjnp] sanei_bjnp_find_devices: Added all configured
> scanners, now
> >> do auto detection...
> >> [bjnp] prepare_socket: lo is not a valid IPv4 interface,
> skipping...
> >> [bjnp] prepare_socket: eno1 is IPv4 capable, sending broadcast,
> >> socket = 50
> >> [bjnp] prepare_socket: lo is not a valid IPv6 interface,
> skipping...
> >> [bjnp] prepare_socket: eno1 is IPv6 capable, sending broadcast,
> >> socket = 51
> >> [bjnp] prepare_socket: eno1 is IPv6 capable, sending broadcast,
> >> socket = 52
> >> [bjnp] prepare_socket: eno1 is IPv6 capable, sending broadcast,
> >> socket = 53
> >> [bjnp] sanei_find_devices: scanner discovery finished...
> >> [pixma] pixma_find_scanners() found 0 devices
> >>
> >
>
More information about the sane-devel
mailing list