[Nut-upsdev] tripp lite smart2200RMXL2U error reading protocol

Kjell Claesson kjell.claesson at epost.tidanet.se
Fri May 11 17:42:41 UTC 2007


Hi Lance,

Can you do a

lsusb

So we get the product and vendor id. The driver
seems only to support product-id 0001, so if your
ups have 3012 as product id, it is a new version.

Regards
Kjell

fre 2007-05-11 klockan 11:08 -0500 skrev Lance Thomas:
> I'm working on a gentoo server with Nut 2.0.5-r1 and libusb-0.1.12.
> I originally tried the hidups driver which seemed to work, but produced
> a large amount of unhandled events.  Then I tried the newhidups which
> told me my ups wasn't supported.  When I try using
> 
> tripplite_usb -u root -DDDD /proc/bus/usb/002/002
> 
> I get that there isn't a match.  But when I try using 
> 
> tripplite_usb -DDDD -a tripplite1 
> 
> with the following ups.conf:
> [tripplite1]
>         driver = tripplite_usb
>         port = /proc/bus/usb/002/002
>         productid = 3012
>         bus = 002
>         desc = "top ups"
> 
> I get it to run and find the HID, but it returns the following errors
> before quitting:
> Detected a UPS: Tripp Lite /TRIPP LITE SMART2200RMXL2U
> send_cmd(msg_len=3, type='W')
> libusb_get_interrupt() returned 4 instead of 8
> libusb_get_interrupt() returned 4 instead of 8
> libusb_get_interrupt() returned 4 instead of 8
> libusb_get_interrupt() returned 4 instead of 8
> libusb_get_interrupt() returned 4 instead of 8
> libusb_get_interrupt() returned 4 instead of 8
> libusb_get_interrupt() returned 4 instead of 8
> libusb_get_interrupt() returned 4 instead of 8
> libusb_get_interrupt() returned 4 instead of 8
> send_cmd: send_try = 3, recv_try = 3
> 
> Could not reset watchdog. Please send model information to nut-upsdev
> mailing list
> send_cmd(msg_len=2, type='
> libusb_get_interrupt() returned 4 instead of 8
> libusb_get_interrupt() returned 4 instead of 8
> libusb_get_interrupt() returned 4 instead of 8
> libusb_get_interrupt() returned 4 instead of 8
> libusb_get_interrupt() returned 4 instead of 8
> libusb_get_interrupt() returned 4 instead of 8
> libusb_get_interrupt() returned 4 instead of 8
> libusb_get_interrupt() returned 4 instead of 8
> libusb_get_interrupt() returned 4 instead of 8
> send_cmd: send_try = 3, recv_try = 3
> 
> Error reading protocol
> 
> 
> Any suggestions?
> ____________________________________________________________________
> 
> This email and any attachments may contain confidential information and is 
> solely for the intended recipient(s).  Email communications are not considered 
> secure.  If you are not the intended recipient(s) of this email you are expected 
> to disregard the content, delete the message and notify the original sender.
> 
> --University of Wisconsin, Department of Family Medicine--
> ____________________________________________________________________
> 
> **UW DFM**
> 
> 
> _______________________________________________
> Nut-upsdev mailing list
> Nut-upsdev at lists.alioth.debian.org
> http://lists.alioth.debian.org/mailman/listinfo/nut-upsdev




More information about the Nut-upsdev mailing list