[Nut-upsdev] smart1050slt by tripp lite

[chance fulton]

On Sun, 2010-01-31 at 16:09 -0500, Charles Lepple wrote:
> On Jan 31, 2010, at 3:56 PM, chance fulton wrote:
> 
> > On Sun, 2010-01-31 at 14:38 -0500, Charles Lepple wrote:
> >> On Jan 31, 2010, at 1:44 PM, chance fulton wrote:
> >>
> >>> Original Message
> >>>> I have 2 SmartUOS1050SLT's that apparently protocol 3004, has there
> >>>> been
> >>>> any progress on getting these units supported under nut? I am  
> >>>> running
> >>>> version 2.4.1, and get the following output when starting the  
> >>>> driver.
> >>>
> >>>> #lsusb
> >>>> Bus 005 Device 002: ID 09ae:0001 Tripp Lite
> >>>
> >>>> # upsdrvctl -DDDD start
> >>>> Network UPS Tools - UPS driver controller 2.4.1
> >>>> Starting UPS: tripplite
> >>>> exec: /lib/nut/tripplite_usb -a tripplite
> >>>> Network UPS Tools - Tripp Lite OMNIVS / SMARTPRO driver 0.20  
> >>>> (2.4.1)
> >>>> Warning: This is an experimental driver.
> >>>> Some features may not function correctly.
> >>>
> >>>> Detected a UPS: TRIPP LITE/TRIPP LITE SMART1050SLT
> >>>> Unknown input voltage range: 0x02
> >>>> Unknown number of switchable load banks: 0x00
> >>>> Unit ID: 0
> >>>> Unknown protocol (3004)Attached to Tripp Lite SMART1050SLT
> >>>> Unknown value for s[1]: 0x01
> >>
> [...]
> 
> >> Please post a few details about your OS distribution and version.
> >>
> > I have Ubuntu server 9.10 Kernel 2.6.31-17-generic-pae
> > I have just installed Network UPS Tools - UPS driver controller
> > 2.4.1-r2286
> >
> > And still have the same issue.
> 
> I just committed a few changes to SVN. In a few minutes, it should  
> build another tarball for r2294:
> 
> http://buildbot.ghz.cc/public/nut/waterfall?branch=trunk&builder=Debian-etch-x86
> 
> A couple of questions:
> 
>   - When you were testing, how did you run the driver?
>   - Is the Ubuntu package for NUT still installed?
>   - Are you using SVN, or the tarballs?
> 
> thanks,
> 
> - Charles
OK will do, as for the questions.

I run the driver from this command:
sudo /usr/local/ups/bin/upsdrvctl start

I uninstalled the Ubuntu package, and purged the configs. then I copied
in my settings from the old installation to the new config files.

I am using the tarballs as I an new with the whole autoconf thing, and
could not get it going.


I have just removed the previous version, and installed from the svn
trunk version 2297. I now get this.

Network UPS Tools - UPS driver controller 2.4.1-2297
Network UPS Tools - Tripp Lite OMNIVS / SMARTPRO driver 0.20
(2.4.1-2297)
Warning: This is an experimental driver.
Some features may not function correctly.

Detected a UPS: TRIPP LITE/TRIPP LITE SMART1050SLT     
libusb_get_interrupt() returned 0 instead of 8 while sending 3a 00 ff 0d
00 00 00 00 '........'
libusb_get_interrupt() returned 0 instead of 8 while sending 3a 00 ff 0d
00 00 00 00 '........'
libusb_get_interrupt() returned 0 instead of 8 while sending 3a 00 ff 0d
00 00 00 00 '........'
libusb_get_interrupt() returned 0 instead of 8 while sending 3a 00 ff 0d
00 00 00 00 '........'
libusb_get_interrupt() returned 0 instead of 8 while sending 3a 00 ff 0d
00 00 00 00 '........'
libusb_get_interrupt() returned 0 instead of 8 while sending 3a 00 ff 0d
00 00 00 00 '........'
libusb_get_interrupt() returned 0 instead of 8 while sending 3a 00 ff 0d
00 00 00 00 '........'
libusb_get_interrupt() returned 0 instead of 8 while sending 3a 00 ff 0d
00 00 00 00 '........'
libusb_get_interrupt() returned 0 instead of 8 while sending 3a 00 ff 0d
00 00 00 00 '........'
libusb_get_interrupt() returned 0 instead of 8 while sending 3a 00 ff 0d
00 00 00 00 '........'
Unknown input voltage range: 0x02
Unknown number of switchable load banks: 0x00
Unit ID: 0
Unknown protocol (3004)Attached to Tripp Lite SMART1050SLT
Unknown value for s[1]: 0x01

Pretty much the same, just more debug info.