[Nut-upsdev] smart1050slt by tripp lite

[Charles Lepple]

On Jan 31, 2010, at 4:29 PM, chance fulton wrote:

> On Sun, 2010-01-31 at 16:09 -0500, Charles Lepple wrote:
>> On Jan 31, 2010, at 3:56 PM, chance fulton wrote:
>>
>>> On Sun, 2010-01-31 at 14:38 -0500, Charles Lepple wrote:
>>>> On Jan 31, 2010, at 1:44 PM, chance fulton wrote:
>>>>
>>>>> Original Message
>>>>>> I have 2 SmartUOS1050SLT's that apparently protocol 3004, has  
>>>>>> there
>>>>>> been
>>>>>> any progress on getting these units supported under nut? I am
>>>>>> running
>>>>>> version 2.4.1, and get the following output when starting the
>>>>>> driver.
>>>>>
>>>>>> #lsusb
>>>>>> Bus 005 Device 002: ID 09ae:0001 Tripp Lite
>>>>>
>>>>>> # upsdrvctl -DDDD start
>>>>>> Network UPS Tools - UPS driver controller 2.4.1
>>>>>> Starting UPS: tripplite
>>>>>> exec: /lib/nut/tripplite_usb -a tripplite
>>>>>> Network UPS Tools - Tripp Lite OMNIVS / SMARTPRO driver 0.20
>>>>>> (2.4.1)
>>>>>> Warning: This is an experimental driver.
>>>>>> Some features may not function correctly.
>>>>>
>>>>>> Detected a UPS: TRIPP LITE/TRIPP LITE SMART1050SLT
>>>>>> Unknown input voltage range: 0x02
>>>>>> Unknown number of switchable load banks: 0x00
>>>>>> Unit ID: 0
>>>>>> Unknown protocol (3004)Attached to Tripp Lite SMART1050SLT
>>>>>> Unknown value for s[1]: 0x01
>>>>
>> [...]
>>
>>>> Please post a few details about your OS distribution and version.
>>>>
>>> I have Ubuntu server 9.10 Kernel 2.6.31-17-generic-pae
>>> I have just installed Network UPS Tools - UPS driver controller
>>> 2.4.1-r2286
>>>
>>> And still have the same issue.
>>
>> I just committed a few changes to SVN. In a few minutes, it should
>> build another tarball for r2294:
>>
>> http://buildbot.ghz.cc/public/nut/waterfall?branch=trunk&builder=Debian-etch-x86
>>
>> A couple of questions:
>>
>>  - When you were testing, how did you run the driver?
>>  - Is the Ubuntu package for NUT still installed?
>>  - Are you using SVN, or the tarballs?
>>
>> thanks,
>>
>> - Charles
> OK will do, as for the questions.
>
> I run the driver from this command:
> sudo /usr/local/ups/bin/upsdrvctl start
>
> I uninstalled the Ubuntu package, and purged the configs. then I  
> copied
> in my settings from the old installation to the new config files.
>
> I am using the tarballs as I an new with the whole autoconf thing, and
> could not get it going.
>
>
> I have just removed the previous version, and installed from the svn
> trunk version 2297. I now get this.
>
> Network UPS Tools - UPS driver controller 2.4.1-2297
> Network UPS Tools - Tripp Lite OMNIVS / SMARTPRO driver 0.20
> (2.4.1-2297)
> Warning: This is an experimental driver.
> Some features may not function correctly.
>
> Detected a UPS: TRIPP LITE/TRIPP LITE SMART1050SLT
> libusb_get_interrupt() returned 0 instead of 8 while sending 3a 00  
> ff 0d
> 00 00 00 00 '........'
> libusb_get_interrupt() returned 0 instead of 8 while sending 3a 00  
> ff 0d
> 00 00 00 00 '........'
> libusb_get_interrupt() returned 0 instead of 8 while sending 3a 00  
> ff 0d
> 00 00 00 00 '........'
> libusb_get_interrupt() returned 0 instead of 8 while sending 3a 00  
> ff 0d
> 00 00 00 00 '........'
> libusb_get_interrupt() returned 0 instead of 8 while sending 3a 00  
> ff 0d
> 00 00 00 00 '........'
> libusb_get_interrupt() returned 0 instead of 8 while sending 3a 00  
> ff 0d
> 00 00 00 00 '........'
> libusb_get_interrupt() returned 0 instead of 8 while sending 3a 00  
> ff 0d
> 00 00 00 00 '........'
> libusb_get_interrupt() returned 0 instead of 8 while sending 3a 00  
> ff 0d
> 00 00 00 00 '........'
> libusb_get_interrupt() returned 0 instead of 8 while sending 3a 00  
> ff 0d
> 00 00 00 00 '........'
> libusb_get_interrupt() returned 0 instead of 8 while sending 3a 00  
> ff 0d
> 00 00 00 00 '........'
> Unknown input voltage range: 0x02
> Unknown number of switchable load banks: 0x00
> Unit ID: 0
> Unknown protocol (3004)Attached to Tripp Lite SMART1050SLT
> Unknown value for s[1]: 0x01
>
> Pretty much the same, just more debug info.

Another tarball coming: http://buildbot.ghz.cc/public/nut/waterfall?branch=branches%2Ftripplite-proto-3004&builder=Debian-etch-x86&reload=none

This time, when you start it, run the driver directly (without  
upsdrvctl), and send the output to a logfile. It'll be something like:

    /usr/local/ups/bin/tripplite_usb -a name-of-ups -DDD | tee /tmp/ 
log-r2298.txt

Also, you can start upsd, and record what 'upsc name-of-ups at localhost'  
shows.

Please gzip both logs before mailing them to the list.

Thanks,

- Charles