[Nut-upsuser] Liebert PSIXR 3000 intellislot web card support with NUT 2.6.0

[John Huong]

Hi,

Just started using NUT with a Liebert PSI-XR 3000 with an Intellislot web card.

It seems I can't get it to run properly.

I am using NUT 2.6.0 built from source on Ubuntu 8.0.4 .

My build parameters are :

./configure --enable-strip
--with-linux-hiddev=/usr/include/linux/hiddev.h
--with-udev-dir=/lib/udev \
	    --prefix=/usr \
	    --exec-prefix=/ \
	    --sysconfdir=/etc/nut \
	    --mandir=/usr/share/man \
	    --libdir=/lib \
	    --includedir=/usr/include \
	    --without-ssl \
	    --with-dev \
	    --enable-static \
	    --with-statepath=/var/run/nut \
	    --with-altpidpath=/var/run/nut \
	    --with-drvpath=/lib/nut \
	    --with-htmlpath=/usr/share/nut/www \
	    --with-pidpath=/var/run/nut \
	    --datadir=/usr/share/nut \
	    --with-pkgconfig-dir=/usr/lib/pkgconfig \
	    --with-user=nut --with-group=nut


I get this when I run upsdrvctl start

Detected LiebertPSI on host 192.168.0.11 (mib: ietf 1.3)
[liebertpsiweb] unhandled ASN 0x6 recieved from 1.3.6.1.2.1.33.1.7.1.0

Then when I run /etc/init.d/nut I get

 * Starting Network UPS Tools                                            [ OK ]

Broadcast Message from nut at mail.sop.com.my
        (somewhere) at 1:02 ...

Communications with UPS liebertpsiweb at localhost lost

Running upsc liebertpsiweb at localhost gets me :

battery.charge: 100.00
battery.current: 0.00
battery.runtime: 0.00
battery.runtime.low: 120.00
battery.temperature: 30.00
battery.voltage: 55.00
beeper.status: enabled
device.mfr: Emerson Network Power
device.model: LiebertPSI
device.type: ups
driver.name: snmp-ups
driver.parameter.mibs: auto
driver.parameter.pollinterval: 2
driver.parameter.port: 192.168.0.11
driver.version: 2.6.0
driver.version.internal: 0.50 (mib: ietf 1.3)
input.bypass.phases: 0.00
input.current: 0.00
input.frequency: 50.00
input.frequency.nominal: 50.00
input.phases: 1.00
input.realpower: 0.00
input.transfer.high: 0.00
input.transfer.low: 0.00
input.voltage: 247.00
input.voltage.nominal: 2300.00
output.current: 0.00
output.frequency: 50.00
output.frequency.nominal: 50.00
output.phases: 1.00
output.power.nominal: 0.00
output.realpower: 0.00
output.realpower.nominal: 0.00
output.voltage: 249.00
output.voltage.nominal: 2300.00
ups.firmware: EX000842
ups.firmware.aux: 2.39.CP504.ABE.00
ups.load: 17.00
ups.mfr: Emerson Network Power
ups.model: LiebertPSI
ups.start.auto: no
ups.status:
ups.test.result: done and passed
ups.timer.reboot: -1
ups.timer.shutdown: -1
ups.timer.start: -1

What can I do or is this particular model not supported?