[sane-devel] HP ScanJet 6100C Configuration

[Frank Roberts - SOTL]

Thanks again for the help Peter.
I did the following:
1. Restored sane.d to its original configuration.
2. In hp.conf changed /dev/scanner to /dev/sg0
3. Confirmed that hp is active in dll.conf. 
4. Tested system - no change.
5. As root did: chmood 666 /dev/sg0
6. Tested system - no change.

Thanks
Frank

On Monday 05 August 2002 01:14, Peter Kirchgessner wrote:
>
> Don't remove the files. You need at least dll.conf too. And check that
> it has the line with hp activated.
>
> --Peter
>
> Frank Roberts - SOTL wrote:
> > Thanks for the help Peter.
> >
> > I did the following:
> > 1. Changed /dev/scanner to /dev/sg0
> > 2. Made directory sane.d-bak
> > 3. Removed all configuration files from sane.d except hp.conf
> > 4. As root did chmood 666 /dev/sg0
> >
> > I received exactly the same results - no change.
> >
> > Thanks
> > Frank
> >
> > On Sunday 04 August 2002 04:06, Peter Kirchgessner wrote:
> >>Hi Frank,
> >>
> >>try the hp.conf with
> >>scsi HP
> >>/dev/sg0
> >>
> >>If this does not work, you may have a second hp.conf at
> >>/etc/sane.d/hp.conf. Try that one with the same content.
> >>If it still does not work, do as root a
> >>
> >>chmod 666 /dev/sg0
> >>and try it again.
> >>
> >>Sincerely
> >>Peter
> >>
> >>Frank Roberts - SOTL wrote:
> >>>Hi All:
> >>>
> >>>I hope You people will have time to help a relative novice with
> >>>configuration of an HP 6100 C which is to be used intermidently on 2
> >>>different RH 7.3 systems.
> >>>
> >>>
> >>>As stated previously the scanner is an HP 6100C if I issue the command:
> >>>The scanner is connected by 40 pin scsi.
> >>>Several commands were issues with the following results:
> >>>
> >>>$ scanimage --list devices
> >>>sg0     HP C2520A 36644
> >>>sg1     Mitsumi    CD-R
> >>>sg2     Soney      CD-RW
> >>>
> >>>
> >>>$ cat /proc/scsi/scsa
> >>>Attached devices:
> >>>Host: scsi0 Channel: 00 Id: 04 Lun: 00 Vendor: HP Model: C2520A Rev:
> >>> 3644 Type: Processor ANSI SCSI revision: 02
> >>>Host: scsi1 Channel: 00 Id: 00 Lun: 00 Vendor: MITSUMI Model: CD-ROM
> >>>FX4830T!B Rev: R02C Type: CD-ROM ANSI SCSI revision: 02
> >>>Host: scsi1 Channel: 00 Id: 01 Lun: 00 Vendor: SONY Model: CD-RW
> >>> CRX175E2 Rev: S002 Type: CD-ROM ANSI SCSI revision: 02
> >>>
> >>>
> >>>$ export   SANE_DEBUGG_HP=17
> >>>$ scanimage -L
> >>>[scanei_debug] Setting debug level of hp to 17
> >>>[hp] sane_init called[hp]
> >>>[hp] sane_init will finish with Success
> >>>[hp] sane_get_devices called
> >>>[hp] hp_read_config: hp backend v0.95 start reading conf file
> >>>[hp] hp_read_config: processing line <scsi HP>
> >>>[hp] hp_read_config: processing line </dev/scaner>
> >>>[hp] hp_read_config: attach scsi HP
> >>>[hp] hp_read_config: attach /dev/scanner
> >>>[hp] hp_get_dev: New device /dev/scanner, connect-scsi, scsi-request=1
> >>>[hp] sanei_hp_device_new: /dev/scanner
> >>>[hp] scsi_newopen failed (Invalid argument)
> >>>[hp] /dev/scanner: Can't open scsi device
> >>>[hp] sane_get_devices will finish with Success
> >>>[hp] sane_exit called
> >>>[hp] sane_exit will finish
> >>>
> >>>
> >>>The sane configuration file /etc/sane.d/ho.conf is as follows:
> >>>scsi HP
> >>>/dev/scannet
> >>>
> >>>I would appreciate any advice you people may be able to offer.
> >>>
> >>>Thanks
> >>>Frank
> >>>
> >>>Thanks