[sane-devel] xsane preview and scanning problem

[Oliver Rauch]

Hello.

Disable "quality calibration" if it is enabled.

Oliver

Am Mit, 2004-12-29 um 18.45 schrieb Rich:
> Hi,
> 
> I searched through the archives and found an article "xsane preview and
> scanning problem" from Tue, 4 Feb 2003 20:47:53 by HoonKook Shim that
> explains the same problems I am now encountering.  
> 
> I recently upgraded to 2.6.10 from 2.6.9, hoping to address some scsi
> issues with cdrecord and xsane.  However, after upgrading, the same
> issues exist.
> 
> My scanner is detecting correctly. After applying permissions to
> the /dev/scanner, I can run as root or any user. I can run the preview
> over and over, with no issues.  The scanner works correctly. However,
> when I press scan - xsane freezes after the scanner begins to move.
> 
> I've tried scanimage, same issue.  It detects the scanner, but cannot
> scan an image.
> 
> Once xsane or scanimage freezes, the scanner can no longer be detected.
> However, if I reset the power on the scanner after about 15 seconds or
> so, after reset, I can once again detect the scanner successfully.
> 
> I also commented out any backend I'm not using in the dll.conf file.
> 
> 
> Here are the specs:
> 
> 
> Linux 2.6.10
> 
> scsi1 : Adaptec AIC7XXX EISA/VLB/PCI SCSI HBA DRIVER, Rev 6.2.36
>         <Adaptec 2930CU SCSI adapter>
>         aic7860: Ultra Single Channel A, SCSI Id=7, 3/253 SCBs
> 
> sr0: scsi3-mmc drive: 0x/56x cd/rw xa/form2 cdda tray
> Uniform CD-ROM driver Revision: 3.20
> Attached scsi CD-ROM sr0 at scsi0, channel 0, id 0, lun 0
>   Vendor: UMAX      Model: Astra 2200        Rev: V2.2
>   Type:   Scanner                            ANSI SCSI revision: 02
> Attached scsi generic sg1 at scsi1, channel 0, id 2, lun 0,  type 6
>   Vendor: HP        Model: CD-Writer+ 9200   Rev: 1.0c
>   Type:   CD-ROM                             ANSI SCSI revision: 04
> sr1: scsi3-mmc drive: 32x/32x writer cd/rw xa/form2 cdda tray
> Attached scsi CD-ROM sr1 at scsi1, channel 0, id 4, lun 0
> Attached scsi generic sg2 at scsi1, channel 0, id 4, lun 0,  type 5
> 
> sane-find-scanner
> found SCSI scanner "UMAX Astra 2200 V2.2" at /dev/scanner
> found SCSI scanner "UMAX Astra 2200 V2.2" at /dev/sg1
> 
> scanimage -L
> device `umax:/dev/scanner' is a UMAX     Astra 2200       flatbed
> scanner
> device `umax:/dev/sg1' is a UMAX     Astra 2200       flatbed scanner
> 
> 
> xsane-0.96 (c) 1998-2004 Oliver Rauch
>   Email: Oliver.Rauch@xsane.org
>   package xsane-0.96
>   compiled with GTK-2.4.10
>   with GIMP support, compiled with GIMP-2.0.4
>   XSane output formats: jpeg, png, pnm, ps, tiff, txt
> sane-backends-1.0.15
> sane-frontends-1.0.13
> 
> 
> Thanks,
> Regards
> Rich
> 
> 
> 
>