[sane-devel] Configuring SCSI-Scanner under SUSE 10.1
Daniel Spannbauer
ds at marco.de
Wed Aug 9 10:24:02 UTC 2006
Hallo,
if Yast would do his Job I don't have to set it up Manually. :)
Now I've read the man-Pages but don't get forward.
I attached the scanimage.log after debugging.
Can anyboady figure out where the Problem is?
In dll.conf there is now an entry "epson".
Regards
Daniel Spannbauer
Johannes Meixner schrieb:
> Hello,
>
> On Aug 9 09:46 Daniel Spannbauer wrote (shortened):
>
>> I'm trying to configure a Epson Perfection 1640 on the SCSI on SUSE 10.1 In
>> my /etc/sane.d/epson.conf ist CSI enabled (scsi EPSON is written in there).
>> Sane-find-scanner lists the scanner on /dev/sg1, but scanimage -L doesn't
>> find that scanner.
>>
>
> For general information how to set up a scanner manually, see
> http://en.opensuse.org/SDB:Configuring_Scanners_from_SUSE_LINUX_9.2
> in particular read about the dll meta-backend and the section
> about "Trouble-Shooting (Debugging)".
>
> To get (a lot of) debug messages use
> ----------------------------------------------------------------------
> export SANE_DEBUG_DLL=4
> export SANE_DEBUG_EPSON=128
> export SANE_DEBUG_SANEI_SCSI=255
> scanimage -L 2>&1 | tee /tmp/scanimage.log
> ----------------------------------------------------------------------
> and inspect /tmp/scanimage.log for suspicious messages.
> See "man sane-dll", "man sane-epson", "man sane-scsi".
>
>
> Kind Regards
> Johannes Meixner
>
-------------- next part --------------
[sanei_debug] Setting debug level of dll to 4.
[dll] sane_init: SANE dll backend version 1.0.12 from sane-backends 1.0.18
[dll] add_backend: adding backend `net'
[dll] add_backend: adding backend `abaton'
[dll] add_backend: adding backend `agfafocus'
[dll] add_backend: adding backend `apple'
[dll] add_backend: adding backend `avision'
[dll] add_backend: adding backend `artec'
[dll] add_backend: adding backend `artec_eplus48u'
[dll] add_backend: adding backend `as6e'
[dll] add_backend: adding backend `bh'
[dll] add_backend: adding backend `canon'
[dll] add_backend: adding backend `canon630u'
[dll] add_backend: adding backend `coolscan'
[dll] add_backend: adding backend `coolscan2'
[dll] add_backend: adding backend `dell1600n_net'
[dll] add_backend: adding backend `dmc'
[dll] add_backend: adding backend `epson'
[dll] add_backend: adding backend `fujitsu'
[dll] add_backend: adding backend `genesys'
[dll] add_backend: adding backend `gt68xx'
[dll] add_backend: adding backend `hp'
[dll] add_backend: adding backend `hpsj5s'
[dll] add_backend: adding backend `hp3500'
[dll] add_backend: adding backend `hp4200'
[dll] add_backend: adding backend `hp5400'
[dll] add_backend: adding backend `ibm'
[dll] add_backend: adding backend `leo'
[dll] add_backend: adding backend `lexmark'
[dll] add_backend: adding backend `ma1509'
[dll] add_backend: adding backend `matsushita'
[dll] add_backend: adding backend `microtek'
[dll] add_backend: adding backend `microtek2'
[dll] add_backend: adding backend `mustek'
[dll] add_backend: adding backend `mustek_usb'
[dll] add_backend: adding backend `mustek_usb2'
[dll] add_backend: adding backend `nec'
[dll] add_backend: adding backend `niash'
[dll] add_backend: adding backend `pie'
[dll] add_backend: adding backend `pint'
[dll] add_backend: adding backend `pixma'
[dll] add_backend: adding backend `plustek'
[dll] add_backend: adding backend `qcam'
[dll] add_backend: adding backend `ricoh'
[dll] add_backend: adding backend `s9036'
[dll] add_backend: adding backend `sceptre'
[dll] add_backend: adding backend `sharp'
[dll] add_backend: adding backend `sm3600'
[dll] add_backend: adding backend `sm3840'
[dll] add_backend: adding backend `snapscan'
[dll] add_backend: adding backend `sp15c'
[dll] add_backend: adding backend `tamarack'
[dll] add_backend: adding backend `teco1'
[dll] add_backend: adding backend `teco2'
[dll] add_backend: adding backend `teco3'
[dll] add_backend: adding backend `u12'
[dll] add_backend: adding backend `umax'
[dll] add_backend: adding backend `umax1220u'
[dll] add_backend: adding backend `v4l'
[dll] sane_get_devices
[dll] load: searching backend `v4l' in `/usr/local/lib/sane'
[dll] load: trying to load `/usr/local/lib/sane/libsane-v4l.so.1'
[dll] load: dlopen()ing `/usr/local/lib/sane/libsane-v4l.so.1'
[dll] init: initializing backend `v4l'
[dll] init: backend `v4l' is version 1.0.4
[dll] load: searching backend `umax1220u' in `/usr/local/lib/sane'
[dll] load: trying to load `/usr/local/lib/sane/libsane-umax1220u.so.1'
[dll] load: dlopen()ing `/usr/local/lib/sane/libsane-umax1220u.so.1'
[dll] init: initializing backend `umax1220u'
[dll] init: backend `umax1220u' is version 1.0.1
[dll] load: searching backend `umax' in `/usr/local/lib/sane'
[dll] load: trying to load `/usr/local/lib/sane/libsane-umax.so.1'
[dll] load: dlopen()ing `/usr/local/lib/sane/libsane-umax.so.1'
[dll] init: initializing backend `umax'
[sanei_debug] Setting debug level of sanei_scsi to 255.
[sanei_debug] Setting debug level of sanei_scsi to 255.
[sanei_debug] Setting debug level of sanei_scsi to 255.
[sanei_debug] Setting debug level of sanei_scsi to 255.
[sanei_debug] Setting debug level of sanei_scsi to 255.
[sanei_debug] Setting debug level of sanei_scsi to 255.
[sanei_debug] Setting debug level of sanei_scsi to 255.
[sanei_debug] Setting debug level of sanei_scsi to 255.
[sanei_debug] Setting debug level of sanei_scsi to 255.
[sanei_debug] Setting debug level of sanei_scsi to 255.
[sanei_debug] Setting debug level of sanei_scsi to 255.
[sanei_debug] Setting debug level of sanei_scsi to 255.
[sanei_debug] Setting debug level of sanei_scsi to 255.
[sanei_debug] Setting debug level of sanei_scsi to 255.
[sanei_debug] Setting debug level of sanei_scsi to 255.
[sanei_debug] Setting debug level of sanei_scsi to 255.
[sanei_debug] Setting debug level of sanei_scsi to 255.
[sanei_debug] Setting debug level of sanei_scsi to 255.
[sanei_scsi] sanei_scsi_find_devices: vendor=(null) model=(null) type=Processor
bus=0 chan=0 id=5 lun=0 num=1
[sanei_scsi] lx_chk_id: 0,0 0,0 5,5 0,0
[sanei_scsi] lx_chk_devicename: matched device(direct): /dev/sg1
[sanei_scsi] get_max_buffer_size for /dev/sg1: 131072
[sanei_scsi] sanei_scsi_open: sanei_scsi_max_request_size=131072 bytes
[sanei_scsi] sanei_scsi_open: open of `/dev/scanner' failed: No such file or directory
[dll] init: backend `umax' is version 1.0.44
[dll] load: searching backend `u12' in `/usr/local/lib/sane'
[dll] load: trying to load `/usr/local/lib/sane/libsane-u12.so.1'
[dll] load: dlopen()ing `/usr/local/lib/sane/libsane-u12.so.1'
[dll] init: initializing backend `u12'
[dll] init: backend `u12' is version 1.0.0
[dll] load: searching backend `teco3' in `/usr/local/lib/sane'
[dll] load: trying to load `/usr/local/lib/sane/libsane-teco3.so.1'
[dll] load: dlopen()ing `/usr/local/lib/sane/libsane-teco3.so.1'
[dll] init: initializing backend `teco3'
[sanei_debug] Setting debug level of sanei_scsi to 255.
[sanei_debug] Setting debug level of sanei_scsi to 255.
[sanei_debug] Setting debug level of sanei_scsi to 255.
[sanei_debug] Setting debug level of sanei_scsi to 255.
[sanei_debug] Setting debug level of sanei_scsi to 255.
[sanei_debug] Setting debug level of sanei_scsi to 255.
[sanei_debug] Setting debug level of sanei_scsi to 255.
[sanei_scsi] sanei_scsi_find_devices: vendor=(null) model=(null) type=Processor
bus=0 chan=0 id=5 lun=0 num=1
[sanei_scsi] lx_chk_id: 0,0 0,0 5,5 0,0
[sanei_scsi] lx_chk_devicename: matched device(direct): /dev/sg1
[sanei_scsi] get_max_buffer_size for /dev/sg1: 131072
[sanei_scsi] sanei_scsi_open: sanei_scsi_max_request_size=131072 bytes
[sanei_scsi] sanei_scsi_open: open of `/dev/scanner' failed: No such file or directory
[dll] init: backend `teco3' is version 1.0.1
[dll] load: searching backend `teco2' in `/usr/local/lib/sane'
[dll] load: trying to load `/usr/local/lib/sane/libsane-teco2.so.1'
[dll] load: dlopen()ing `/usr/local/lib/sane/libsane-teco2.so.1'
[dll] init: initializing backend `teco2'
[sanei_debug] Setting debug level of sanei_scsi to 255.
[sanei_debug] Setting debug level of sanei_scsi to 255.
[sanei_debug] Setting debug level of sanei_scsi to 255.
[sanei_debug] Setting debug level of sanei_scsi to 255.
[sanei_debug] Setting debug level of sanei_scsi to 255.
[sanei_debug] Setting debug level of sanei_scsi to 255.
[sanei_debug] Setting debug level of sanei_scsi to 255.
[sanei_debug] Setting debug level of sanei_scsi to 255.
[sanei_debug] Setting debug level of sanei_scsi to 255.
[sanei_debug] Setting debug level of sanei_scsi to 255.
[sanei_debug] Setting debug level of sanei_scsi to 255.
[sanei_debug] Setting debug level of sanei_scsi to 255.
[sanei_scsi] sanei_scsi_find_devices: vendor=(null) model=(null) type=Processor
bus=0 chan=0 id=5 lun=0 num=1
[sanei_scsi] lx_chk_id: 0,0 0,0 5,5 0,0
[sanei_scsi] lx_chk_devicename: matched device(direct): /dev/sg1
[sanei_scsi] get_max_buffer_size for /dev/sg1: 131072
[sanei_scsi] sanei_scsi_open: sanei_scsi_max_request_size=131072 bytes
[sanei_scsi] sanei_scsi_open: open of `/dev/scanner' failed: No such file or directory
[dll] init: backend `teco2' is version 1.0.9
[dll] load: searching backend `teco1' in `/usr/local/lib/sane'
[dll] load: trying to load `/usr/local/lib/sane/libsane-teco1.so.1'
[dll] load: dlopen()ing `/usr/local/lib/sane/libsane-teco1.so.1'
[dll] init: initializing backend `teco1'
[sanei_debug] Setting debug level of sanei_scsi to 255.
[sanei_debug] Setting debug level of sanei_scsi to 255.
[sanei_debug] Setting debug level of sanei_scsi to 255.
[sanei_debug] Setting debug level of sanei_scsi to 255.
[sanei_debug] Setting debug level of sanei_scsi to 255.
[sanei_debug] Setting debug level of sanei_scsi to 255.
[sanei_debug] Setting debug level of sanei_scsi to 255.
[sanei_debug] Setting debug level of sanei_scsi to 255.
[sanei_scsi] sanei_scsi_find_devices: vendor=(null) model=(null) type=Processor
bus=0 chan=0 id=5 lun=0 num=1
[sanei_scsi] lx_chk_id: 0,0 0,0 5,5 0,0
[sanei_scsi] lx_chk_devicename: matched device(direct): /dev/sg1
[sanei_scsi] get_max_buffer_size for /dev/sg1: 131072
[sanei_scsi] sanei_scsi_open: sanei_scsi_max_request_size=131072 bytes
[sanei_scsi] sanei_scsi_open: open of `/dev/scanner' failed: No such file or directory
[dll] init: backend `teco1' is version 1.0.10
[dll] load: searching backend `tamarack' in `/usr/local/lib/sane'
[dll] load: trying to load `/usr/local/lib/sane/libsane-tamarack.so.1'
[dll] load: dlopen()ing `/usr/local/lib/sane/libsane-tamarack.so.1'
[dll] init: initializing backend `tamarack'
[sanei_debug] Setting debug level of sanei_scsi to 255.
[sanei_debug] Setting debug level of sanei_scsi to 255.
[sanei_debug] Setting debug level of sanei_scsi to 255.
[sanei_debug] Setting debug level of sanei_scsi to 255.
[sanei_scsi] sanei_scsi_find_devices: vendor=(null) model=(null) type=Processor
bus=0 chan=0 id=5 lun=0 num=1
[sanei_scsi] lx_chk_id: 0,0 0,0 5,5 0,0
[sanei_scsi] lx_chk_devicename: matched device(direct): /dev/sg1
[sanei_scsi] get_max_buffer_size for /dev/sg1: 131072
[sanei_scsi] sanei_scsi_open: sanei_scsi_max_request_size=131072 bytes
[sanei_scsi] sanei_scsi_open: open of `/dev/scanner' failed: No such file or directory
[dll] init: backend `tamarack' is version 1.0.0
[dll] load: searching backend `sp15c' in `/usr/local/lib/sane'
[dll] load: trying to load `/usr/local/lib/sane/libsane-sp15c.so.1'
[dll] load: dlopen()ing `/usr/local/lib/sane/libsane-sp15c.so.1'
[dll] init: initializing backend `sp15c'
[sanei_debug] Setting debug level of sanei_scsi to 255.
[dll] init: backend `sp15c' is version 1.0.0
[dll] load: searching backend `snapscan' in `/usr/local/lib/sane'
[dll] load: trying to load `/usr/local/lib/sane/libsane-snapscan.so.1'
[dll] load: dlopen()ing `/usr/local/lib/sane/libsane-snapscan.so.1'
[dll] init: initializing backend `snapscan'
[sanei_debug] Setting debug level of sanei_scsi to 255.
[sanei_debug] Setting debug level of sanei_scsi to 255.
[sanei_debug] Setting debug level of sanei_scsi to 255.
[sanei_debug] Setting debug level of sanei_scsi to 255.
[dll] init: backend `snapscan' is version 1.4.53
[dll] load: searching backend `sm3840' in `/usr/local/lib/sane'
[dll] load: trying to load `/usr/local/lib/sane/libsane-sm3840.so.1'
[dll] load: dlopen()ing `/usr/local/lib/sane/libsane-sm3840.so.1'
[dll] init: initializing backend `sm3840'
[dll] init: backend `sm3840' is version 1.0.0
[dll] load: searching backend `sm3600' in `/usr/local/lib/sane'
[dll] load: trying to load `/usr/local/lib/sane/libsane-sm3600.so.1'
[dll] load: dlopen()ing `/usr/local/lib/sane/libsane-sm3600.so.1'
[dll] init: initializing backend `sm3600'
[dll] init: backend `sm3600' is version 1.0.6
[dll] load: searching backend `sharp' in `/usr/local/lib/sane'
[dll] load: trying to load `/usr/local/lib/sane/libsane-sharp.so.1'
[dll] load: dlopen()ing `/usr/local/lib/sane/libsane-sharp.so.1'
[dll] init: initializing backend `sharp'
[sanei_debug] Setting debug level of sanei_scsi to 255.
[sanei_debug] Setting debug level of sanei_scsi to 255.
[sanei_debug] Setting debug level of sanei_scsi to 255.
[sanei_debug] Setting debug level of sanei_scsi to 255.
[sanei_scsi] sanei_scsi_find_devices: vendor=(null) model=(null) type=Processor
bus=0 chan=0 id=5 lun=0 num=1
[sanei_scsi] lx_chk_id: 0,0 0,0 5,5 0,0
[sanei_scsi] lx_chk_devicename: matched device(direct): /dev/sg1
[sanei_scsi] get_max_buffer_size for /dev/sg1: 131072
[sanei_scsi] sanei_scsi_open: sanei_scsi_max_request_size=131072 bytes
[sanei_scsi] sanei_scsi_open: open of `/dev/scanner' failed: No such file or directory
[dll] init: backend `sharp' is version 1.0.0
[dll] load: searching backend `sceptre' in `/usr/local/lib/sane'
[dll] load: trying to load `/usr/local/lib/sane/libsane-sceptre.so.1'
[dll] load: dlopen()ing `/usr/local/lib/sane/libsane-sceptre.so.1'
[dll] init: initializing backend `sceptre'
[sanei_debug] Setting debug level of sanei_scsi to 255.
[sanei_debug] Setting debug level of sanei_scsi to 255.
[sanei_debug] Setting debug level of sanei_scsi to 255.
[sanei_debug] Setting debug level of sanei_scsi to 255.
[sanei_scsi] sanei_scsi_find_devices: vendor=(null) model=(null) type=Processor
bus=0 chan=0 id=5 lun=0 num=1
[sanei_scsi] lx_chk_id: 0,0 0,0 5,5 0,0
[sanei_scsi] lx_chk_devicename: matched device(direct): /dev/sg1
[sanei_scsi] get_max_buffer_size for /dev/sg1: 131072
[sanei_scsi] sanei_scsi_open: sanei_scsi_max_request_size=131072 bytes
[sanei_scsi] sanei_scsi_open: open of `/dev/scanner' failed: No such file or directory
[dll] init: backend `sceptre' is version 1.0.10
[dll] load: searching backend `s9036' in `/usr/local/lib/sane'
[dll] load: trying to load `/usr/local/lib/sane/libsane-s9036.so.1'
[dll] load: dlopen()ing `/usr/local/lib/sane/libsane-s9036.so.1'
[dll] init: initializing backend `s9036'
[sanei_debug] Setting debug level of sanei_scsi to 255.
[sanei_debug] Setting debug level of sanei_scsi to 255.
[sanei_debug] Setting debug level of sanei_scsi to 255.
[sanei_scsi] sanei_scsi_find_devices: vendor=(null) model=(null) type=Processor
bus=0 chan=0 id=5 lun=0 num=1
[sanei_scsi] lx_chk_id: 0,0 0,0 5,5 0,0
[sanei_scsi] lx_chk_devicename: matched device(direct): /dev/sg1
[sanei_scsi] get_max_buffer_size for /dev/sg1: 131072
[sanei_scsi] sanei_scsi_open: sanei_scsi_max_request_size=131072 bytes
[sanei_scsi] sanei_scsi_open: open of `/dev/scanner' failed: No such file or directory
[dll] init: backend `s9036' is version 1.0.0
[dll] load: searching backend `ricoh' in `/usr/local/lib/sane'
[dll] load: trying to load `/usr/local/lib/sane/libsane-ricoh.so.1'
[dll] load: dlopen()ing `/usr/local/lib/sane/libsane-ricoh.so.1'
[dll] init: initializing backend `ricoh'
[sanei_debug] Setting debug level of sanei_scsi to 255.
[sanei_debug] Setting debug level of sanei_scsi to 255.
[sanei_debug] Setting debug level of sanei_scsi to 255.
[sanei_scsi] sanei_scsi_find_devices: vendor=(null) model=(null) type=Processor
bus=0 chan=0 id=5 lun=0 num=1
[sanei_scsi] lx_chk_id: 0,0 0,0 5,5 0,0
[sanei_scsi] lx_chk_devicename: matched device(direct): /dev/sg1
[sanei_scsi] get_max_buffer_size for /dev/sg1: 131072
[sanei_scsi] sanei_scsi_open: sanei_scsi_max_request_size=131072 bytes
[sanei_scsi] sanei_scsi_open: open of `/dev/scanner' failed: No such file or directory
[dll] init: backend `ricoh' is version 1.0.0
[dll] load: searching backend `qcam' in `/usr/local/lib/sane'
[dll] load: trying to load `/usr/local/lib/sane/libsane-qcam.so.1'
[dll] load: dlopen()ing `/usr/local/lib/sane/libsane-qcam.so.1'
[dll] init: initializing backend `qcam'
[dll] init: backend `qcam' is version 1.0.0
[dll] load: searching backend `plustek' in `/usr/local/lib/sane'
[dll] load: trying to load `/usr/local/lib/sane/libsane-plustek.so.1'
[dll] load: dlopen()ing `/usr/local/lib/sane/libsane-plustek.so.1'
[dll] init: initializing backend `plustek'
[dll] init: backend `plustek' is version 1.0.0
[dll] load: searching backend `pixma' in `/usr/local/lib/sane'
[dll] load: trying to load `/usr/local/lib/sane/libsane-pixma.so.1'
[dll] load: dlopen()ing `/usr/local/lib/sane/libsane-pixma.so.1'
[dll] init: initializing backend `pixma'
[dll] init: backend `pixma' is version 1.0.11
[dll] load: searching backend `pint' in `/usr/local/lib/sane'
[dll] load: trying to load `/usr/local/lib/sane/libsane-pint.so.1'
[dll] load: couldn't open `/usr/local/lib/sane/libsane-pint.so.1' (No such file or directory)
[dll] load: couldn't find backend `pint' (No such file or directory)
[dll] load: searching backend `pie' in `/usr/local/lib/sane'
[dll] load: trying to load `/usr/local/lib/sane/libsane-pie.so.1'
[dll] load: dlopen()ing `/usr/local/lib/sane/libsane-pie.so.1'
[dll] init: initializing backend `pie'
[sanei_debug] Setting debug level of sanei_scsi to 255.
[sanei_debug] Setting debug level of sanei_scsi to 255.
[sanei_debug] Setting debug level of sanei_scsi to 255.
[sanei_debug] Setting debug level of sanei_scsi to 255.
[sanei_debug] Setting debug level of sanei_scsi to 255.
[sanei_debug] Setting debug level of sanei_scsi to 255.
[sanei_scsi] sanei_scsi_find_devices: vendor=(null) model=(null) type=Processor
bus=0 chan=0 id=5 lun=0 num=1
[sanei_scsi] lx_chk_id: 0,0 0,0 5,5 0,0
[sanei_scsi] lx_chk_devicename: matched device(direct): /dev/sg1
[sanei_scsi] get_max_buffer_size for /dev/sg1: 131072
[sanei_scsi] sanei_scsi_open: sanei_scsi_max_request_size=131072 bytes
[sanei_scsi] sanei_scsi_open: open of `/dev/scanner' failed: No such file or directory
[dll] init: backend `pie' is version 1.0.9
[dll] load: searching backend `niash' in `/usr/local/lib/sane'
[dll] load: trying to load `/usr/local/lib/sane/libsane-niash.so.1'
[dll] load: dlopen()ing `/usr/local/lib/sane/libsane-niash.so.1'
[dll] init: initializing backend `niash'
[dll] init: backend `niash' is version 1.0.1
[dll] load: searching backend `nec' in `/usr/local/lib/sane'
[dll] load: trying to load `/usr/local/lib/sane/libsane-nec.so.1'
[dll] load: dlopen()ing `/usr/local/lib/sane/libsane-nec.so.1'
[dll] init: initializing backend `nec'
[sanei_debug] Setting debug level of sanei_scsi to 255.
[sanei_debug] Setting debug level of sanei_scsi to 255.
[sanei_debug] Setting debug level of sanei_scsi to 255.
[sanei_scsi] sanei_scsi_find_devices: vendor=(null) model=(null) type=Processor
bus=0 chan=0 id=5 lun=0 num=1
[sanei_scsi] lx_chk_id: 0,0 0,0 5,5 0,0
[sanei_scsi] lx_chk_devicename: matched device(direct): /dev/sg1
[sanei_scsi] get_max_buffer_size for /dev/sg1: 131072
[sanei_scsi] sanei_scsi_open: sanei_scsi_max_request_size=131072 bytes
[sanei_scsi] sanei_scsi_open: open of `/dev/scanner' failed: No such file or directory
[dll] init: backend `nec' is version 1.0.0
[dll] load: searching backend `mustek_usb2' in `/usr/local/lib/sane'
[dll] load: trying to load `/usr/local/lib/sane/libsane-mustek_usb2.so.1'
[dll] load: dlopen()ing `/usr/local/lib/sane/libsane-mustek_usb2.so.1'
[dll] init: initializing backend `mustek_usb2'
[dll] init: backend `mustek_usb2' is version 1.0.10
[dll] load: searching backend `mustek_usb' in `/usr/local/lib/sane'
[dll] load: trying to load `/usr/local/lib/sane/libsane-mustek_usb.so.1'
[dll] load: dlopen()ing `/usr/local/lib/sane/libsane-mustek_usb.so.1'
[dll] init: initializing backend `mustek_usb'
[dll] init: backend `mustek_usb' is version 1.0.18
[dll] load: searching backend `mustek' in `/usr/local/lib/sane'
[dll] load: trying to load `/usr/local/lib/sane/libsane-mustek.so.1'
[dll] load: dlopen()ing `/usr/local/lib/sane/libsane-mustek.so.1'
[dll] init: initializing backend `mustek'
[sanei_debug] Setting debug level of sanei_scsi to 255.
[sanei_debug] Setting debug level of sanei_scsi to 255.
[sanei_debug] Setting debug level of sanei_scsi to 255.
[sanei_debug] Setting debug level of sanei_scsi to 255.
[sanei_debug] Setting debug level of sanei_scsi to 255.
[sanei_scsi] sanei_scsi_find_devices: vendor=(null) model=(null) type=Processor
bus=0 chan=0 id=5 lun=0 num=1
[sanei_scsi] lx_chk_id: 0,0 0,0 5,5 0,0
[sanei_scsi] lx_chk_devicename: matched device(direct): /dev/sg1
[sanei_scsi] get_max_buffer_size for /dev/sg1: 131072
[sanei_scsi] sanei_scsi_open: sanei_scsi_max_request_size=131072 bytes
[sanei_scsi] sanei_scsi_open: open of `/dev/scanner' failed: No such file or directory
[dll] init: backend `mustek' is version 1.0.138
[dll] load: searching backend `microtek2' in `/usr/local/lib/sane'
[dll] load: trying to load `/usr/local/lib/sane/libsane-microtek2.so.1'
[dll] load: dlopen()ing `/usr/local/lib/sane/libsane-microtek2.so.1'
[dll] init: initializing backend `microtek2'
[sanei_debug] Setting debug level of sanei_scsi to 255.
[sanei_debug] Setting debug level of sanei_scsi to 255.
[sanei_debug] Setting debug level of sanei_scsi to 255.
[sanei_debug] Setting debug level of sanei_scsi to 255.
[sanei_scsi] sanei_scsi_find_devices: vendor=(null) model=(null) type=Processor
bus=0 chan=0 id=5 lun=0 num=1
[sanei_scsi] lx_chk_id: 0,0 0,0 5,5 0,0
[sanei_scsi] lx_chk_devicename: matched device(direct): /dev/sg1
[sanei_scsi] get_max_buffer_size for /dev/sg1: 131072
[sanei_scsi] sanei_scsi_open: sanei_scsi_max_request_size=131072 bytes
[sanei_scsi] sanei_scsi_open: open of `/dev/scanner' failed: No such file or directory
[dll] init: backend `microtek2' is version 1.0.0
[sanei_debug] Setting debug level of sanei_scsi to 255.
[sanei_scsi] sanei_scsi_open: open of `/dev/scanner' failed: No such file or directory
[dll] load: searching backend `microtek' in `/usr/local/lib/sane'
[dll] load: trying to load `/usr/local/lib/sane/libsane-microtek.so.1'
[dll] load: dlopen()ing `/usr/local/lib/sane/libsane-microtek.so.1'
[dll] init: initializing backend `microtek'
[sanei_debug] Setting debug level of sanei_scsi to 255.
[sanei_debug] Setting debug level of sanei_scsi to 255.
[sanei_debug] Setting debug level of sanei_scsi to 255.
[sanei_debug] Setting debug level of sanei_scsi to 255.
[sanei_scsi] sanei_scsi_find_devices: vendor=(null) model=(null) type=Processor
bus=0 chan=0 id=5 lun=0 num=1
[sanei_scsi] lx_chk_id: 0,0 0,0 5,5 0,0
[sanei_scsi] lx_chk_devicename: matched device(direct): /dev/sg1
[sanei_scsi] get_max_buffer_size for /dev/sg1: 131072
[sanei_scsi] sanei_scsi_open: sanei_scsi_max_request_size=131072 bytes
[sanei_scsi] sanei_scsi_open: open of `/dev/scanner' failed: No such file or directory
[dll] init: backend `microtek' is version 1.0.0
[dll] load: searching backend `matsushita' in `/usr/local/lib/sane'
[dll] load: trying to load `/usr/local/lib/sane/libsane-matsushita.so.1'
[dll] load: dlopen()ing `/usr/local/lib/sane/libsane-matsushita.so.1'
[dll] init: initializing backend `matsushita'
[sanei_debug] Setting debug level of sanei_scsi to 255.
[sanei_debug] Setting debug level of sanei_scsi to 255.
[sanei_debug] Setting debug level of sanei_scsi to 255.
[sanei_debug] Setting debug level of sanei_scsi to 255.
[sanei_debug] Setting debug level of sanei_scsi to 255.
[sanei_debug] Setting debug level of sanei_scsi to 255.
[sanei_debug] Setting debug level of sanei_scsi to 255.
[sanei_debug] Setting debug level of sanei_scsi to 255.
[sanei_scsi] sanei_scsi_find_devices: vendor=(null) model=(null) type=Processor
bus=0 chan=0 id=5 lun=0 num=1
[sanei_scsi] lx_chk_id: 0,0 0,0 5,5 0,0
[sanei_scsi] lx_chk_devicename: matched device(direct): /dev/sg1
[sanei_scsi] get_max_buffer_size for /dev/sg1: 131072
[sanei_scsi] sanei_scsi_open: sanei_scsi_max_request_size=131072 bytes
[sanei_scsi] sanei_scsi_open: open of `/dev/scanner' failed: No such file or directory
[dll] init: backend `matsushita' is version 1.0.7
[dll] load: searching backend `ma1509' in `/usr/local/lib/sane'
[dll] load: trying to load `/usr/local/lib/sane/libsane-ma1509.so.1'
[dll] load: dlopen()ing `/usr/local/lib/sane/libsane-ma1509.so.1'
[dll] init: initializing backend `ma1509'
[dll] init: backend `ma1509' is version 1.0.3
[dll] load: searching backend `lexmark' in `/usr/local/lib/sane'
[dll] load: trying to load `/usr/local/lib/sane/libsane-lexmark.so.1'
[dll] load: dlopen()ing `/usr/local/lib/sane/libsane-lexmark.so.1'
[dll] init: initializing backend `lexmark'
[dll] init: backend `lexmark' is version 1.0.0
[dll] load: searching backend `leo' in `/usr/local/lib/sane'
[dll] load: trying to load `/usr/local/lib/sane/libsane-leo.so.1'
[dll] load: dlopen()ing `/usr/local/lib/sane/libsane-leo.so.1'
[dll] init: initializing backend `leo'
[sanei_debug] Setting debug level of sanei_scsi to 255.
[sanei_debug] Setting debug level of sanei_scsi to 255.
[sanei_debug] Setting debug level of sanei_scsi to 255.
[sanei_debug] Setting debug level of sanei_scsi to 255.
[sanei_debug] Setting debug level of sanei_scsi to 255.
[sanei_scsi] sanei_scsi_find_devices: vendor=(null) model=(null) type=Processor
bus=0 chan=0 id=5 lun=0 num=1
[sanei_scsi] lx_chk_id: 0,0 0,0 5,5 0,0
[sanei_scsi] lx_chk_devicename: matched device(direct): /dev/sg1
[sanei_scsi] get_max_buffer_size for /dev/sg1: 131072
[sanei_scsi] sanei_scsi_open: sanei_scsi_max_request_size=131072 bytes
[sanei_scsi] sanei_scsi_open: open of `/dev/scanner' failed: No such file or directory
[dll] init: backend `leo' is version 1.0.11
[dll] load: searching backend `ibm' in `/usr/local/lib/sane'
[dll] load: trying to load `/usr/local/lib/sane/libsane-ibm.so.1'
[dll] load: dlopen()ing `/usr/local/lib/sane/libsane-ibm.so.1'
[dll] init: initializing backend `ibm'
[sanei_debug] Setting debug level of sanei_scsi to 255.
[sanei_debug] Setting debug level of sanei_scsi to 255.
[sanei_debug] Setting debug level of sanei_scsi to 255.
[sanei_scsi] sanei_scsi_find_devices: vendor=(null) model=(null) type=Processor
bus=0 chan=0 id=5 lun=0 num=1
[sanei_scsi] lx_chk_id: 0,0 0,0 5,5 0,0
[sanei_scsi] lx_chk_devicename: matched device(direct): /dev/sg1
[sanei_scsi] get_max_buffer_size for /dev/sg1: 131072
[sanei_scsi] sanei_scsi_open: sanei_scsi_max_request_size=131072 bytes
[sanei_scsi] sanei_scsi_open: open of `/dev/scanner' failed: No such file or directory
[dll] init: backend `ibm' is version 1.0.0
[dll] load: searching backend `hp5400' in `/usr/local/lib/sane'
[dll] load: trying to load `/usr/local/lib/sane/libsane-hp5400.so.1'
[dll] load: dlopen()ing `/usr/local/lib/sane/libsane-hp5400.so.1'
[dll] init: initializing backend `hp5400'
[dll] init: backend `hp5400' is version 1.0.3
[dll] load: searching backend `hp4200' in `/usr/local/lib/sane'
[dll] load: trying to load `/usr/local/lib/sane/libsane-hp4200.so.1'
[dll] load: dlopen()ing `/usr/local/lib/sane/libsane-hp4200.so.1'
[dll] init: initializing backend `hp4200'
[dll] init: backend `hp4200' is version 1.0.0
[dll] load: searching backend `hp3500' in `/usr/local/lib/sane'
[dll] load: trying to load `/usr/local/lib/sane/libsane-hp3500.so.1'
[dll] load: dlopen()ing `/usr/local/lib/sane/libsane-hp3500.so.1'
[dll] init: initializing backend `hp3500'
[dll] init: backend `hp3500' is version 1.0.0
[dll] load: searching backend `hpsj5s' in `/usr/local/lib/sane'
[dll] load: trying to load `/usr/local/lib/sane/libsane-hpsj5s.so.1'
[dll] load: dlopen()ing `/usr/local/lib/sane/libsane-hpsj5s.so.1'
[dll] init: initializing backend `hpsj5s'
[dll] init: backend `hpsj5s' is version 1.0.3
[dll] load: searching backend `hp' in `/usr/local/lib/sane'
[dll] load: trying to load `/usr/local/lib/sane/libsane-hp.so.1'
[dll] load: dlopen()ing `/usr/local/lib/sane/libsane-hp.so.1'
[dll] init: initializing backend `hp'
[dll] init: backend `hp' is version 1.0.8
[sanei_debug] Setting debug level of sanei_scsi to 255.
[sanei_debug] Setting debug level of sanei_scsi to 255.
[sanei_debug] Setting debug level of sanei_scsi to 255.
[sanei_debug] Setting debug level of sanei_scsi to 255.
[sanei_scsi] sanei_scsi_find_devices: vendor=(null) model=(null) type=Processor
bus=0 chan=0 id=5 lun=0 num=1
[sanei_scsi] lx_chk_id: 0,0 0,0 5,5 0,0
[sanei_scsi] lx_chk_devicename: matched device(direct): /dev/sg1
[sanei_scsi] get_max_buffer_size for /dev/sg1: 131072
[sanei_scsi] sanei_scsi_open: sanei_scsi_max_request_size=131072 bytes
[sanei_scsi] sanei_scsi_open: open of `/dev/scanner' failed: No such file or directory
[dll] load: searching backend `gt68xx' in `/usr/local/lib/sane'
[dll] load: trying to load `/usr/local/lib/sane/libsane-gt68xx.so.1'
[dll] load: dlopen()ing `/usr/local/lib/sane/libsane-gt68xx.so.1'
[dll] init: initializing backend `gt68xx'
[dll] init: backend `gt68xx' is version 1.0.81
[dll] load: searching backend `genesys' in `/usr/local/lib/sane'
[dll] load: trying to load `/usr/local/lib/sane/libsane-genesys.so.1'
[dll] load: dlopen()ing `/usr/local/lib/sane/libsane-genesys.so.1'
[dll] init: initializing backend `genesys'
[dll] init: backend `genesys' is version 1.0.8
[dll] load: searching backend `fujitsu' in `/usr/local/lib/sane'
[dll] load: trying to load `/usr/local/lib/sane/libsane-fujitsu.so.1'
[dll] load: dlopen()ing `/usr/local/lib/sane/libsane-fujitsu.so.1'
[dll] init: initializing backend `fujitsu'
[dll] init: backend `fujitsu' is version 1.0.33
[sanei_debug] Setting debug level of sanei_scsi to 255.
[dll] load: searching backend `epson' in `/usr/local/lib/sane'
[dll] load: trying to load `/usr/local/lib/sane/libsane-epson.so.1'
[dll] load: dlopen()ing `/usr/local/lib/sane/libsane-epson.so.1'
[dll] init: initializing backend `epson'
[sanei_debug] Setting debug level of epson to 128.
[epson] sane_init: sane-backends 1.0.18
[epson] sane_init, ># epson.conf<
[epson] sane_init, >#<
[epson] sane_init, ># here are some examples for how to configure the EPSON backend<
[epson] sane_init, >#<
[epson] sane_init, ># SCSI scanner:<
[epson] sane_init, >#scsi EPSON<
[epson] sane_init, ># for the GT-6500, comment out the previous line and uncomment the following line:<
[epson] sane_init, >#scsi<
[epson] sane_init, >#<
[epson] sane_init, ># Parallel port scanner:<
[epson] sane_init, >#pio 0x278<
[epson] sane_init, >#pio 0x378<
[epson] sane_init, >#pio 0x3BC<
[epson] sane_init, >#<
[epson] sane_init, ># USB scanner:<
[epson] sane_init, ># There are two different methods of configuring a USB scanner: libusb and the kernel module<
[epson] sane_init, ># For any system with libusb support (which is pretty much any recent Linux distribution) the<
[epson] sane_init, ># following line is sufficient. This however assumes that the connected scanner (or to be more<
[epson] sane_init, ># accurate, it's device ID) is known to the backend.<
[epson] sane_init, >usb<
[epson] attach_one_usb()
[epson] SANE Epson Backend v0.2.46 - 2006-06-11
[epson] attach(, 3)
[epson] attach: opening
[epson] sane_init, ># For libusb support for unknown scanners use the following command<
[epson] sane_init, ># usb <product ID> <device ID><
[epson] sane_init, ># e.g.:<
[epson] sane_init, ># usb 0x4b8 0x110<
[epson] sane_init, ># And for the scanner module, use the following configuration:<
[epson] sane_init, >#usb /dev/usbscanner0<
[epson] sane_init, >#usb /dev/usb/scanner0<
[dll] init: backend `epson' is version 1.0.246
[epson] sane_get_devices()
[dll] load: searching backend `dmc' in `/usr/local/lib/sane'
[dll] load: trying to load `/usr/local/lib/sane/libsane-dmc.so.1'
[dll] load: dlopen()ing `/usr/local/lib/sane/libsane-dmc.so.1'
[dll] init: initializing backend `dmc'
[sanei_debug] Setting debug level of sanei_scsi to 255.
[sanei_debug] Setting debug level of sanei_scsi to 255.
[sanei_debug] Setting debug level of sanei_scsi to 255.
[sanei_scsi] sanei_scsi_find_devices: vendor=(null) model=(null) type=Processor
bus=0 chan=0 id=5 lun=0 num=1
[sanei_scsi] lx_chk_id: 0,0 0,0 5,5 0,0
[sanei_scsi] lx_chk_devicename: matched device(direct): /dev/sg1
[sanei_scsi] get_max_buffer_size for /dev/sg1: 131072
[sanei_scsi] sanei_scsi_open: sanei_scsi_max_request_size=131072 bytes
[sanei_scsi] sanei_scsi_open: open of `/dev/camera' failed: No such file or directory
[dll] init: backend `dmc' is version 1.0.0
[dll] load: searching backend `dell1600n_net' in `/usr/local/lib/sane'
[dll] load: trying to load `/usr/local/lib/sane/libsane-dell1600n_net.so.1'
[dll] load: couldn't open `/usr/local/lib/sane/libsane-dell1600n_net.so.1' (No such file or directory)
[dll] load: couldn't find backend `dell1600n_net' (No such file or directory)
[dll] load: searching backend `coolscan2' in `/usr/local/lib/sane'
[dll] load: trying to load `/usr/local/lib/sane/libsane-coolscan2.so.1'
[dll] load: dlopen()ing `/usr/local/lib/sane/libsane-coolscan2.so.1'
[dll] init: initializing backend `coolscan2'
[dll] init: backend `coolscan2' is version 1.0.0
[sanei_debug] Setting debug level of sanei_scsi to 255.
[dll] load: searching backend `coolscan' in `/usr/local/lib/sane'
[dll] load: trying to load `/usr/local/lib/sane/libsane-coolscan.so.1'
[dll] load: dlopen()ing `/usr/local/lib/sane/libsane-coolscan.so.1'
[dll] init: initializing backend `coolscan'
[sanei_debug] Setting debug level of sanei_scsi to 255.
[sanei_debug] Setting debug level of sanei_scsi to 255.
[sanei_debug] Setting debug level of sanei_scsi to 255.
[sanei_debug] Setting debug level of sanei_scsi to 255.
[sanei_scsi] sanei_scsi_find_devices: vendor=(null) model=(null) type=Processor
bus=0 chan=0 id=5 lun=0 num=1
[sanei_scsi] lx_chk_id: 0,0 0,0 5,5 0,0
[sanei_scsi] lx_chk_devicename: matched device(direct): /dev/sg1
[sanei_scsi] get_max_buffer_size for /dev/sg1: 131072
[sanei_scsi] sanei_scsi_open: sanei_scsi_max_request_size=131072 bytes
[sanei_scsi] sanei_scsi_open: open of `/dev/scanner' failed: No such file or directory
[dll] init: backend `coolscan' is version 1.0.0
[dll] load: searching backend `canon630u' in `/usr/local/lib/sane'
[dll] load: trying to load `/usr/local/lib/sane/libsane-canon630u.so.1'
[dll] load: dlopen()ing `/usr/local/lib/sane/libsane-canon630u.so.1'
[dll] init: initializing backend `canon630u'
[dll] init: backend `canon630u' is version 1.0.1
[dll] load: searching backend `canon' in `/usr/local/lib/sane'
[dll] load: trying to load `/usr/local/lib/sane/libsane-canon.so.1'
[dll] load: dlopen()ing `/usr/local/lib/sane/libsane-canon.so.1'
[dll] init: initializing backend `canon'
[sanei_debug] Setting debug level of sanei_scsi to 255.
[sanei_debug] Setting debug level of sanei_scsi to 255.
[sanei_debug] Setting debug level of sanei_scsi to 255.
[sanei_scsi] sanei_scsi_find_devices: vendor=(null) model=(null) type=Processor
bus=0 chan=0 id=5 lun=0 num=1
[sanei_scsi] lx_chk_id: 0,0 0,0 5,5 0,0
[sanei_scsi] lx_chk_devicename: matched device(direct): /dev/sg1
[sanei_scsi] get_max_buffer_size for /dev/sg1: 131072
[sanei_scsi] sanei_scsi_open: sanei_scsi_max_request_size=131072 bytes
[sanei_scsi] sanei_scsi_open: open of `/dev/scanner' failed: No such file or directory
[dll] init: backend `canon' is version 1.0.0
[dll] load: searching backend `bh' in `/usr/local/lib/sane'
[dll] load: trying to load `/usr/local/lib/sane/libsane-bh.so.1'
[dll] load: dlopen()ing `/usr/local/lib/sane/libsane-bh.so.1'
[dll] init: initializing backend `bh'
[sanei_debug] Setting debug level of sanei_scsi to 255.
[sanei_debug] Setting debug level of sanei_scsi to 255.
[sanei_debug] Setting debug level of sanei_scsi to 255.
[sanei_debug] Setting debug level of sanei_scsi to 255.
[sanei_scsi] sanei_scsi_find_devices: vendor=(null) model=(null) type=Processor
bus=0 chan=0 id=5 lun=0 num=1
[sanei_scsi] lx_chk_id: 0,0 0,0 5,5 0,0
[sanei_scsi] lx_chk_devicename: matched device(direct): /dev/sg1
[sanei_scsi] get_max_buffer_size for /dev/sg1: 131072
[sanei_scsi] sanei_scsi_open: sanei_scsi_max_request_size=131072 bytes
[sanei_scsi] sanei_scsi_open: open of `/dev/scanner' failed: No such file or directory
[dll] init: backend `bh' is version 1.0.4
[dll] load: searching backend `as6e' in `/usr/local/lib/sane'
[dll] load: trying to load `/usr/local/lib/sane/libsane-as6e.so.1'
[dll] load: dlopen()ing `/usr/local/lib/sane/libsane-as6e.so.1'
[dll] init: initializing backend `as6e'
[dll] load: searching backend `artec_eplus48u' in `/usr/local/lib/sane'
[dll] load: trying to load `/usr/local/lib/sane/libsane-artec_eplus48u.so.1'
[dll] load: dlopen()ing `/usr/local/lib/sane/libsane-artec_eplus48u.so.1'
[dll] init: initializing backend `artec_eplus48u'
[dll] init: backend `artec_eplus48u' is version 1.0.0
[dll] load: searching backend `artec' in `/usr/local/lib/sane'
[dll] load: trying to load `/usr/local/lib/sane/libsane-artec.so.1'
[dll] load: dlopen()ing `/usr/local/lib/sane/libsane-artec.so.1'
[dll] init: initializing backend `artec'
[sanei_debug] Setting debug level of sanei_scsi to 255.
[sanei_debug] Setting debug level of sanei_scsi to 255.
[sanei_debug] Setting debug level of sanei_scsi to 255.
[sanei_debug] Setting debug level of sanei_scsi to 255.
[sanei_scsi] sanei_scsi_find_devices: vendor=(null) model=(null) type=Processor
bus=0 chan=0 id=5 lun=0 num=1
[sanei_scsi] lx_chk_id: 0,0 0,0 5,5 0,0
[sanei_scsi] lx_chk_devicename: matched device(direct): /dev/sg1
[sanei_scsi] get_max_buffer_size for /dev/sg1: 131072
[sanei_scsi] sanei_scsi_open: sanei_scsi_max_request_size=131072 bytes
[sanei_scsi] sanei_scsi_open: open of `/dev/scanner' failed: No such file or directory
[dll] init: backend `artec' is version 1.0.0
[dll] load: searching backend `avision' in `/usr/local/lib/sane'
[dll] load: trying to load `/usr/local/lib/sane/libsane-avision.so.1'
[dll] load: dlopen()ing `/usr/local/lib/sane/libsane-avision.so.1'
[dll] init: initializing backend `avision'
[sanei_debug] Setting debug level of sanei_scsi to 255.
[sanei_debug] Setting debug level of sanei_scsi to 255.
[sanei_debug] Setting debug level of sanei_scsi to 255.
[sanei_debug] Setting debug level of sanei_scsi to 255.
[sanei_debug] Setting debug level of sanei_scsi to 255.
[sanei_debug] Setting debug level of sanei_scsi to 255.
[sanei_debug] Setting debug level of sanei_scsi to 255.
[sanei_debug] Setting debug level of sanei_scsi to 255.
[sanei_debug] Setting debug level of sanei_scsi to 255.
[sanei_debug] Setting debug level of sanei_scsi to 255.
[sanei_debug] Setting debug level of sanei_scsi to 255.
[sanei_debug] Setting debug level of sanei_scsi to 255.
[sanei_debug] Setting debug level of sanei_scsi to 255.
[sanei_debug] Setting debug level of sanei_scsi to 255.
[sanei_debug] Setting debug level of sanei_scsi to 255.
[sanei_debug] Setting debug level of sanei_scsi to 255.
[sanei_debug] Setting debug level of sanei_scsi to 255.
[sanei_debug] Setting debug level of sanei_scsi to 255.
[sanei_debug] Setting debug level of sanei_scsi to 255.
[sanei_debug] Setting debug level of sanei_scsi to 255.
[sanei_debug] Setting debug level of sanei_scsi to 255.
[sanei_debug] Setting debug level of sanei_scsi to 255.
[sanei_debug] Setting debug level of sanei_scsi to 255.
[sanei_debug] Setting debug level of sanei_scsi to 255.
[sanei_debug] Setting debug level of sanei_scsi to 255.
[sanei_debug] Setting debug level of sanei_scsi to 255.
[sanei_debug] Setting debug level of sanei_scsi to 255.
[sanei_debug] Setting debug level of sanei_scsi to 255.
[sanei_debug] Setting debug level of sanei_scsi to 255.
[sanei_debug] Setting debug level of sanei_scsi to 255.
[sanei_debug] Setting debug level of sanei_scsi to 255.
[sanei_debug] Setting debug level of sanei_scsi to 255.
[sanei_debug] Setting debug level of sanei_scsi to 255.
[sanei_debug] Setting debug level of sanei_scsi to 255.
[sanei_debug] Setting debug level of sanei_scsi to 255.
[sanei_debug] Setting debug level of sanei_scsi to 255.
[sanei_debug] Setting debug level of sanei_scsi to 255.
[sanei_debug] Setting debug level of sanei_scsi to 255.
[sanei_debug] Setting debug level of sanei_scsi to 255.
[sanei_debug] Setting debug level of sanei_scsi to 255.
[sanei_debug] Setting debug level of sanei_scsi to 255.
[sanei_debug] Setting debug level of sanei_scsi to 255.
[sanei_debug] Setting debug level of sanei_scsi to 255.
[sanei_debug] Setting debug level of sanei_scsi to 255.
[sanei_debug] Setting debug level of sanei_scsi to 255.
[sanei_debug] Setting debug level of sanei_scsi to 255.
[sanei_debug] Setting debug level of sanei_scsi to 255.
[sanei_debug] Setting debug level of sanei_scsi to 255.
[sanei_debug] Setting debug level of sanei_scsi to 255.
[sanei_debug] Setting debug level of sanei_scsi to 255.
[sanei_debug] Setting debug level of sanei_scsi to 255.
[sanei_debug] Setting debug level of sanei_scsi to 255.
[sanei_debug] Setting debug level of sanei_scsi to 255.
[sanei_debug] Setting debug level of sanei_scsi to 255.
[sanei_debug] Setting debug level of sanei_scsi to 255.
[sanei_debug] Setting debug level of sanei_scsi to 255.
[sanei_debug] Setting debug level of sanei_scsi to 255.
[sanei_debug] Setting debug level of sanei_scsi to 255.
[sanei_debug] Setting debug level of sanei_scsi to 255.
[sanei_debug] Setting debug level of sanei_scsi to 255.
[sanei_debug] Setting debug level of sanei_scsi to 255.
[sanei_debug] Setting debug level of sanei_scsi to 255.
[sanei_debug] Setting debug level of sanei_scsi to 255.
[sanei_debug] Setting debug level of sanei_scsi to 255.
[sanei_debug] Setting debug level of sanei_scsi to 255.
[sanei_debug] Setting debug level of sanei_scsi to 255.
[sanei_debug] Setting debug level of sanei_scsi to 255.
[sanei_debug] Setting debug level of sanei_scsi to 255.
[sanei_debug] Setting debug level of sanei_scsi to 255.
[sanei_debug] Setting debug level of sanei_scsi to 255.
[sanei_debug] Setting debug level of sanei_scsi to 255.
[sanei_debug] Setting debug level of sanei_scsi to 255.
[sanei_debug] Setting debug level of sanei_scsi to 255.
[sanei_debug] Setting debug level of sanei_scsi to 255.
[sanei_debug] Setting debug level of sanei_scsi to 255.
[sanei_debug] Setting debug level of sanei_scsi to 255.
[sanei_debug] Setting debug level of sanei_scsi to 255.
[sanei_debug] Setting debug level of sanei_scsi to 255.
[sanei_debug] Setting debug level of sanei_scsi to 255.
[sanei_debug] Setting debug level of sanei_scsi to 255.
[sanei_debug] Setting debug level of sanei_scsi to 255.
[sanei_debug] Setting debug level of sanei_scsi to 255.
[sanei_debug] Setting debug level of sanei_scsi to 255.
[sanei_debug] Setting debug level of sanei_scsi to 255.
[sanei_debug] Setting debug level of sanei_scsi to 255.
[dll] init: backend `avision' is version 1.0.201
[dll] load: searching backend `apple' in `/usr/local/lib/sane'
[dll] load: trying to load `/usr/local/lib/sane/libsane-apple.so.1'
[dll] load: dlopen()ing `/usr/local/lib/sane/libsane-apple.so.1'
[dll] init: initializing backend `apple'
[sanei_debug] Setting debug level of sanei_scsi to 255.
[sanei_debug] Setting debug level of sanei_scsi to 255.
[sanei_debug] Setting debug level of sanei_scsi to 255.
[sanei_debug] Setting debug level of sanei_scsi to 255.
[sanei_scsi] sanei_scsi_find_devices: vendor=(null) model=(null) type=Processor
bus=0 chan=0 id=5 lun=0 num=1
[sanei_scsi] lx_chk_id: 0,0 0,0 5,5 0,0
[sanei_scsi] lx_chk_devicename: matched device(direct): /dev/sg1
[sanei_scsi] get_max_buffer_size for /dev/sg1: 131072
[sanei_scsi] sanei_scsi_open: sanei_scsi_max_request_size=131072 bytes
[sanei_scsi] sanei_scsi_open: open of `/dev/scanner' failed: No such file or directory
[dll] init: backend `apple' is version 1.0.0
[dll] load: searching backend `agfafocus' in `/usr/local/lib/sane'
[dll] load: trying to load `/usr/local/lib/sane/libsane-agfafocus.so.1'
[dll] load: dlopen()ing `/usr/local/lib/sane/libsane-agfafocus.so.1'
[dll] init: initializing backend `agfafocus'
[sanei_debug] Setting debug level of sanei_scsi to 255.
[sanei_debug] Setting debug level of sanei_scsi to 255.
[sanei_debug] Setting debug level of sanei_scsi to 255.
[sanei_scsi] sanei_scsi_find_devices: vendor=(null) model=(null) type=Processor
bus=0 chan=0 id=5 lun=0 num=1
[sanei_scsi] lx_chk_id: 0,0 0,0 5,5 0,0
[sanei_scsi] lx_chk_devicename: matched device(direct): /dev/sg1
[sanei_scsi] get_max_buffer_size for /dev/sg1: 131072
[sanei_scsi] sanei_scsi_open: sanei_scsi_max_request_size=131072 bytes
[sanei_scsi] sanei_scsi_open: open of `/dev/scanner' failed: No such file or directory
[dll] init: backend `agfafocus' is version 1.0.0
[dll] load: searching backend `abaton' in `/usr/local/lib/sane'
[dll] load: trying to load `/usr/local/lib/sane/libsane-abaton.so.1'
[dll] load: dlopen()ing `/usr/local/lib/sane/libsane-abaton.so.1'
[dll] init: initializing backend `abaton'
[sanei_debug] Setting debug level of sanei_scsi to 255.
[sanei_debug] Setting debug level of sanei_scsi to 255.
[sanei_debug] Setting debug level of sanei_scsi to 255.
[sanei_debug] Setting debug level of sanei_scsi to 255.
[sanei_scsi] sanei_scsi_find_devices: vendor=(null) model=(null) type=Processor
bus=0 chan=0 id=5 lun=0 num=1
[sanei_scsi] lx_chk_id: 0,0 0,0 5,5 0,0
[sanei_scsi] lx_chk_devicename: matched device(direct): /dev/sg1
[sanei_scsi] get_max_buffer_size for /dev/sg1: 131072
[sanei_scsi] sanei_scsi_open: sanei_scsi_max_request_size=131072 bytes
[sanei_scsi] sanei_scsi_open: open of `/dev/scanner' failed: No such file or directory
[dll] init: backend `abaton' is version 1.0.0
[dll] load: searching backend `net' in `/usr/local/lib/sane'
[dll] load: trying to load `/usr/local/lib/sane/libsane-net.so.1'
[dll] load: dlopen()ing `/usr/local/lib/sane/libsane-net.so.1'
[dll] init: initializing backend `net'
[dll] init: backend `net' is version 1.0.18
[dll] sane_get_devices: found 0 devices
[dll] sane_exit: exiting
[dll] sane_exit: calling backend `v4l's exit function
[dll] sane_exit: calling backend `umax1220u's exit function
[dll] sane_exit: calling backend `umax's exit function
[dll] sane_exit: calling backend `u12's exit function
[dll] sane_exit: calling backend `teco3's exit function
[dll] sane_exit: calling backend `teco2's exit function
[dll] sane_exit: calling backend `teco1's exit function
[dll] sane_exit: calling backend `tamarack's exit function
[dll] sane_exit: calling backend `sp15c's exit function
[dll] sane_exit: calling backend `snapscan's exit function
[dll] sane_exit: calling backend `sm3840's exit function
[dll] sane_exit: calling backend `sm3600's exit function
[dll] sane_exit: calling backend `sharp's exit function
[dll] sane_exit: calling backend `sceptre's exit function
[dll] sane_exit: calling backend `s9036's exit function
[dll] sane_exit: calling backend `ricoh's exit function
[dll] sane_exit: calling backend `qcam's exit function
[dll] sane_exit: calling backend `plustek's exit function
[dll] sane_exit: calling backend `pixma's exit function
[dll] sane_exit: calling backend `pie's exit function
[dll] sane_exit: calling backend `niash's exit function
[dll] sane_exit: calling backend `nec's exit function
[dll] sane_exit: calling backend `mustek_usb2's exit function
[dll] sane_exit: calling backend `mustek_usb's exit function
[dll] sane_exit: calling backend `mustek's exit function
[dll] sane_exit: calling backend `microtek2's exit function
[dll] sane_exit: calling backend `microtek's exit function
[dll] sane_exit: calling backend `matsushita's exit function
[dll] sane_exit: calling backend `ma1509's exit function
[dll] sane_exit: calling backend `lexmark's exit function
[dll] sane_exit: calling backend `leo's exit function
[dll] sane_exit: calling backend `ibm's exit function
[dll] sane_exit: calling backend `hp5400's exit function
[dll] sane_exit: calling backend `hp4200's exit function
[dll] sane_exit: calling backend `hp3500's exit function
[dll] sane_exit: calling backend `hpsj5s's exit function
[dll] sane_exit: calling backend `hp's exit function
[dll] sane_exit: calling backend `gt68xx's exit function
[dll] sane_exit: calling backend `genesys's exit function
[dll] sane_exit: calling backend `fujitsu's exit function
[dll] sane_exit: calling backend `epson's exit function
[dll] sane_exit: calling backend `dmc's exit function
[dll] sane_exit: calling backend `coolscan2's exit function
[dll] sane_exit: calling backend `coolscan's exit function
[dll] sane_exit: calling backend `canon630u's exit function
[dll] sane_exit: calling backend `canon's exit function
[dll] sane_exit: calling backend `bh's exit function
[dll] sane_exit: calling backend `artec_eplus48u's exit function
[dll] sane_exit: calling backend `artec's exit function
[dll] sane_exit: calling backend `avision's exit function
[dll] sane_exit: calling backend `apple's exit function
[dll] sane_exit: calling backend `agfafocus's exit function
[dll] sane_exit: calling backend `abaton's exit function
[dll] sane_exit: calling backend `net's exit function
[dll] sane_exit: finished
No scanners were identified. If you were expecting something different,
check that the scanner is plugged in, turned on and detected by the
sane-find-scanner tool (if appropriate). Please read the documentation
which came with this software (README, FAQ, manpages).
More information about the sane-devel
mailing list