[sane-devel] Mustek 1200 CP not working with sane 1.0.17 on FreeBSD

Thu Jul 27 19:25:26 UTC 2006

-----BEGIN PGP SIGNED MESSAGE-----
Hash: SHA1

Hi

I've got an Mustek 1200 CP Scanner wich is connected to my computers
parallelport. I'm using FreeBSD 6.0 and the sane-version from the ports
collection. This is actually version 1.0.17. According to
http://sane-project.org/sane-backends.html#S-MUSTEK-PP the scanner
should be supported "good".

I have libieee1284 on my system installed.

I compiled my sane with libieee1284 and --enable-parport-directio

Now, when I run sane-find-scanner -p it can't find my scanner. I get
same result when I run scanimage -L

I'm doing all this as root, so there should no access/rights problem.
Parallelport support is enabled in my kernel and according to dmesg my
port (0x378 / EPP (tried without EPP too)) is recognized by the system.
I modified dll.conf to activate mustek_pp and made an entry in
mustek_pp.conf:

scanner "mustek" * cis1200

I also tried 0x378, ppi0, /dev/ppi0 instead of the asterisk for the device.

After fiddeling with the debuglevels I got the result following result.
Sorry for the large block: I didn't know wich part is important. This
run was with autoprobing in my mustek_pp.conf.

If anyone has an idea what to do I would appreciate this very much.

Greetings, Sven

su-2.05b# scanimage -L
[sanei_debug] Setting debug level of mustek_pp to 128.
[mustek_pp] sane-mustek_pp, version 0.13-beta. build for SANE 1.0.17
[mustek_pp] backend by Jochen Eisinger <jochen.eisinger at gmx.net>
[sanei_debug] Setting debug level of sanei_pa4s2 to 128.
[sanei_pa4s2] sanei_pa4s2_devices: interface called for the first time
[sanei_pa4s2] sanei_pa4s2_devices: invoked
[sanei_pa4s2] pa4s2_init: static int first_time = 1
[sanei_pa4s2] pa4s2_init: called for the first time
[sanei_pa4s2] pa4s2_init: initializing libieee1284
[sanei_pa4s2] pa4s2_init: 3 ports reported by IEEE 1284 library
[sanei_pa4s2] pa4s2_init: port 0 is `0x278`
[sanei_pa4s2] pa4s2_init: port 1 is `0x378`
[sanei_pa4s2] pa4s2_init: port 2 is `0x3bc`
[sanei_pa4s2] pa4s2_init: allocating port list
[sanei_pa4s2] pa4s2_init: initialized successfully
[mustek_pp] sanei_init: auto probing port
[sanei_pa4s2] sanei_pa4s2_open: called for device '0x278'
[sanei_pa4s2] sanei_pa4s2_open: trying to connect to port
[sanei_pa4s2] pa4s2_open: trying to attach dev `0x278`
[sanei_pa4s2] pa4s2_init: static int first_time = 0
[sanei_pa4s2] pa4s2_init: sanei already initalized
[sanei_pa4s2] pa4s2_open: looking up port in list
[sanei_pa4s2] pa4s2_open: port is in list at port[0]
[sanei_pa4s2] pa4s2_open: setting up port data
[sanei_pa4s2] pa4s2_open: name=0x278 in_use=SANE_TRUE
[sanei_pa4s2] pa4s2_open: enabled=SANE_FALSE mode=PA4S2_MODE_NIB
[sanei_pa4s2] pa4s2_open: opening device
[sanei_pa4s2] pa4s2_open: device `0x278` opened...
[sanei_pa4s2] pa4s2_open: returning SANE_STATUS_GOOD
[sanei_pa4s2] pa4s2_open: open dev `0x278` as fd 0
[sanei_pa4s2] sanei_pa4s2_open: connected to device using fd 0
[sanei_pa4s2] sanei_pa4s2_open: checking for scanner
[sanei_pa4s2] sanei_pa4s2_enable: called for fd 0 with value 1
[sanei_pa4s2] sanei_pa4s2_enable: enable port '0x278'
[sanei_pa4s2] pa4s2_enable: prelock[] = {0xf8, 0xf8, 0x05}
[sanei_pa4s2] sanei_pa4s2_enable: returning SANE_STATUS_GOOD
[sanei_pa4s2] sanei_pa4s2_open: reading ASIC id
[sanei_pa4s2] sanei_pa4s2_readbegin: called for fd 0 and register 0
[sanei_pa4s2] sanei_pa4s2_readbegin: NIB readbegin
[sanei_pa4s2] pa4s2_readbegin_nib: selecting register 0 at '0x278'
[sanei_pa4s2] sanei_pa4s2_readbegin: returning SANE_STATUS_GOOD
[sanei_pa4s2] sanei_pa4s2_readbyte: called with fd 0
[sanei_pa4s2] sanei_pa4s2_readbyte: we hope, the backend called
[sanei_pa4s2] sanei_pa4s2_readbyte: readbegin, so the port is ok...
[sanei_pa4s2] sanei_pa4s2_readbyte: this means, I did not check it - it's
[sanei_pa4s2] sanei_pa4s2_readbyte: not my fault, if your PC burns down.
[sanei_pa4s2] sanei_pa4s2_readbyte: read in NIB mode
[sanei_pa4s2] pa4s2_readbyte_nib: reading value 0x77 from '0x278'
[sanei_pa4s2] sanei_pa4s2_readbyte: read finished
[sanei_pa4s2] sanei_pa4s2_readbyte: got value 0x77
[sanei_pa4s2] sanei_pa4s2_readbyte: returning SANE_STATUS_GOOD
[sanei_pa4s2] sanei_pa4s2_readend: called for fd 0
[sanei_pa4s2] sanei_pa4s2_readend: we hope, the backend called
[sanei_pa4s2] sanei_pa4s2_readend: readbegin, so the port is ok...
[sanei_pa4s2] sanei_pa4s2_readend: this means, I did not check it - it's
[sanei_pa4s2] sanei_pa4s2_readend: not my fault, if your PC burns down.
[sanei_pa4s2] sanei_pa4s2_readend: NIB mode readend
[sanei_pa4s2] pa4s2_readend_nib: end of reading sequence for fd 0
[sanei_pa4s2] sanei_pa4s2_readend: returning SANE_STATUS_GOOD
[sanei_pa4s2] sanei_pa4s2_open: could not find scanner
[sanei_pa4s2] sanei_pa4s2_open: reported ASIC id 0x77
[sanei_pa4s2] sanei_pa4s2_enable: called for fd 0 with value 0
[sanei_pa4s2] sanei_pa4s2_enable: disable port '0x278'
[sanei_pa4s2] pa4s2_disable: state restored
[sanei_pa4s2] sanei_pa4s2_enable: returning SANE_STATUS_GOOD
[sanei_pa4s2] sanei_pa4s2_open: closing port
[sanei_pa4s2] sanei_pa4s2_close: fd = 0
[sanei_pa4s2] sanei_pa4s2_close: freeing resources
[sanei_pa4s2] pa4s2_close: fd=0
[sanei_pa4s2] pa4s2_close: this is port '0x278'
[sanei_pa4s2] pa4s2_close: checking whether port is enabled
[sanei_pa4s2] pa4s2_close: trying to free io port
[sanei_pa4s2] pa4s2_close: marking port as unused
[sanei_pa4s2] pa4s2_close: returning SANE_STATUS_GOOD
[sanei_pa4s2] sanei_pa4s2_close: finished
[sanei_pa4s2] sanei_pa4s2_open: returning SANE_STATUS_INVAL
[mustek_pp] cis_attach: couldn't attach to `0x278' (Invalid argument)
[mustek_pp] cis_attach: trying alternative port name: parport1
[sanei_pa4s2] sanei_pa4s2_open: called for device 'parport1'
[sanei_pa4s2] sanei_pa4s2_open: trying to connect to port
[sanei_pa4s2] pa4s2_open: trying to attach dev `parport1`
[sanei_pa4s2] pa4s2_init: static int first_time = 0
[sanei_pa4s2] pa4s2_init: sanei already initalized
[sanei_pa4s2] pa4s2_open: looking up port in list
[sanei_pa4s2] pa4s2_open: `parport1` is not a valid device name
[sanei_pa4s2] pa4s2_open: returning SANE_STATUS_INVAL
[sanei_pa4s2] sanei_pa4s2_open: connection failed
[mustek_pp] cis_attach: couldn't attach to alternative port `parport1'
(Invalid argument)
[sanei_pa4s2] sanei_pa4s2_open: called for device '0x378'
[sanei_pa4s2] sanei_pa4s2_open: trying to connect to port
[sanei_pa4s2] pa4s2_open: trying to attach dev `0x378`
[sanei_pa4s2] pa4s2_init: static int first_time = 0
[sanei_pa4s2] pa4s2_init: sanei already initalized
[sanei_pa4s2] pa4s2_open: looking up port in list
[sanei_pa4s2] pa4s2_open: port is in list at port[1]
[sanei_pa4s2] pa4s2_open: setting up port data
[sanei_pa4s2] pa4s2_open: name=0x378 in_use=SANE_TRUE
[sanei_pa4s2] pa4s2_open: enabled=SANE_FALSE mode=PA4S2_MODE_NIB
[sanei_pa4s2] pa4s2_open: opening device
[sanei_pa4s2] pa4s2_open: device `0x378` opened...
[sanei_pa4s2] pa4s2_open: returning SANE_STATUS_GOOD
[sanei_pa4s2] pa4s2_open: open dev `0x378` as fd 1
[sanei_pa4s2] sanei_pa4s2_open: connected to device using fd 1
[sanei_pa4s2] sanei_pa4s2_open: checking for scanner
[sanei_pa4s2] sanei_pa4s2_enable: called for fd 1 with value 1
[sanei_pa4s2] sanei_pa4s2_enable: enable port '0x378'
[sanei_pa4s2] pa4s2_enable: prelock[] = {0xf8, 0xf8, 0x0b}
[sanei_pa4s2] sanei_pa4s2_enable: returning SANE_STATUS_GOOD
[sanei_pa4s2] sanei_pa4s2_open: reading ASIC id
[sanei_pa4s2] sanei_pa4s2_readbegin: called for fd 1 and register 0
[sanei_pa4s2] sanei_pa4s2_readbegin: NIB readbegin
[sanei_pa4s2] pa4s2_readbegin_nib: selecting register 0 at '0x378'
[sanei_pa4s2] sanei_pa4s2_readbegin: returning SANE_STATUS_GOOD
[sanei_pa4s2] sanei_pa4s2_readbyte: called with fd 1
[sanei_pa4s2] sanei_pa4s2_readbyte: we hope, the backend called
[sanei_pa4s2] sanei_pa4s2_readbyte: readbegin, so the port is ok...
[sanei_pa4s2] sanei_pa4s2_readbyte: this means, I did not check it - it's
[sanei_pa4s2] sanei_pa4s2_readbyte: not my fault, if your PC burns down.
[sanei_pa4s2] sanei_pa4s2_readbyte: read in NIB mode
[sanei_pa4s2] pa4s2_readbyte_nib: reading value 0x77 from '0x378'
[sanei_pa4s2] sanei_pa4s2_readbyte: read finished
[sanei_pa4s2] sanei_pa4s2_readbyte: got value 0x77
[sanei_pa4s2] sanei_pa4s2_readbyte: returning SANE_STATUS_GOOD
[sanei_pa4s2] sanei_pa4s2_readend: called for fd 1
[sanei_pa4s2] sanei_pa4s2_readend: we hope, the backend called
[sanei_pa4s2] sanei_pa4s2_readend: readbegin, so the port is ok...
[sanei_pa4s2] sanei_pa4s2_readend: this means, I did not check it - it's
[sanei_pa4s2] sanei_pa4s2_readend: not my fault, if your PC burns down.
[sanei_pa4s2] sanei_pa4s2_readend: NIB mode readend
[sanei_pa4s2] pa4s2_readend_nib: end of reading sequence for fd 1
[sanei_pa4s2] sanei_pa4s2_readend: returning SANE_STATUS_GOOD
[sanei_pa4s2] sanei_pa4s2_open: could not find scanner
[sanei_pa4s2] sanei_pa4s2_open: reported ASIC id 0x77
[sanei_pa4s2] sanei_pa4s2_enable: called for fd 1 with value 0
[sanei_pa4s2] sanei_pa4s2_enable: disable port '0x378'
[sanei_pa4s2] pa4s2_disable: state restored
[sanei_pa4s2] sanei_pa4s2_enable: returning SANE_STATUS_GOOD
[sanei_pa4s2] sanei_pa4s2_open: closing port
[sanei_pa4s2] sanei_pa4s2_close: fd = 1
[sanei_pa4s2] sanei_pa4s2_close: freeing resources
[sanei_pa4s2] pa4s2_close: fd=1
[sanei_pa4s2] pa4s2_close: this is port '0x378'
[sanei_pa4s2] pa4s2_close: checking whether port is enabled
[sanei_pa4s2] pa4s2_close: trying to free io port
[sanei_pa4s2] pa4s2_close: marking port as unused
[sanei_pa4s2] pa4s2_close: returning SANE_STATUS_GOOD
[sanei_pa4s2] sanei_pa4s2_close: finished
[sanei_pa4s2] sanei_pa4s2_open: returning SANE_STATUS_INVAL
[mustek_pp] cis_attach: couldn't attach to `0x378' (Invalid argument)
[mustek_pp] cis_attach: trying alternative port name: parport0
[sanei_pa4s2] sanei_pa4s2_open: called for device 'parport0'
[sanei_pa4s2] sanei_pa4s2_open: trying to connect to port
[sanei_pa4s2] pa4s2_open: trying to attach dev `parport0`
[sanei_pa4s2] pa4s2_init: static int first_time = 0
[sanei_pa4s2] pa4s2_init: sanei already initalized
[sanei_pa4s2] pa4s2_open: looking up port in list
[sanei_pa4s2] pa4s2_open: `parport0` is not a valid device name
[sanei_pa4s2] pa4s2_open: returning SANE_STATUS_INVAL
[sanei_pa4s2] sanei_pa4s2_open: connection failed
[mustek_pp] cis_attach: couldn't attach to alternative port `parport0'
(Invalid argument)
[sanei_pa4s2] sanei_pa4s2_open: called for device '0x3bc'
[sanei_pa4s2] sanei_pa4s2_open: trying to connect to port
[sanei_pa4s2] pa4s2_open: trying to attach dev `0x3bc`
[sanei_pa4s2] pa4s2_init: static int first_time = 0
[sanei_pa4s2] pa4s2_init: sanei already initalized
[sanei_pa4s2] pa4s2_open: looking up port in list
[sanei_pa4s2] pa4s2_open: port is in list at port[2]
[sanei_pa4s2] pa4s2_open: setting up port data
[sanei_pa4s2] pa4s2_open: name=0x3bc in_use=SANE_TRUE
[sanei_pa4s2] pa4s2_open: enabled=SANE_FALSE mode=PA4S2_MODE_NIB
[sanei_pa4s2] pa4s2_open: opening device
[sanei_pa4s2] pa4s2_open: device `0x3bc` opened...
[sanei_pa4s2] pa4s2_open: returning SANE_STATUS_GOOD
[sanei_pa4s2] pa4s2_open: open dev `0x3bc` as fd 2
[sanei_pa4s2] sanei_pa4s2_open: connected to device using fd 2
[sanei_pa4s2] sanei_pa4s2_open: checking for scanner
[sanei_pa4s2] sanei_pa4s2_enable: called for fd 2 with value 1
[sanei_pa4s2] sanei_pa4s2_enable: enable port '0x3bc'
[sanei_pa4s2] pa4s2_enable: prelock[] = {0xf8, 0xf8, 0x09}
[sanei_pa4s2] sanei_pa4s2_enable: returning SANE_STATUS_GOOD
[sanei_pa4s2] sanei_pa4s2_open: reading ASIC id
[sanei_pa4s2] sanei_pa4s2_readbegin: called for fd 2 and register 0
[sanei_pa4s2] sanei_pa4s2_readbegin: NIB readbegin
[sanei_pa4s2] pa4s2_readbegin_nib: selecting register 0 at '0x3bc'
[sanei_pa4s2] sanei_pa4s2_readbegin: returning SANE_STATUS_GOOD
[sanei_pa4s2] sanei_pa4s2_readbyte: called with fd 2
[sanei_pa4s2] sanei_pa4s2_readbyte: we hope, the backend called
[sanei_pa4s2] sanei_pa4s2_readbyte: readbegin, so the port is ok...
[sanei_pa4s2] sanei_pa4s2_readbyte: this means, I did not check it - it's
[sanei_pa4s2] sanei_pa4s2_readbyte: not my fault, if your PC burns down.
[sanei_pa4s2] sanei_pa4s2_readbyte: read in NIB mode
[sanei_pa4s2] pa4s2_readbyte_nib: reading value 0x77 from '0x3bc'
[sanei_pa4s2] sanei_pa4s2_readbyte: read finished
[sanei_pa4s2] sanei_pa4s2_readbyte: got value 0x77
[sanei_pa4s2] sanei_pa4s2_readbyte: returning SANE_STATUS_GOOD
[sanei_pa4s2] sanei_pa4s2_readend: called for fd 2
[sanei_pa4s2] sanei_pa4s2_readend: we hope, the backend called
[sanei_pa4s2] sanei_pa4s2_readend: readbegin, so the port is ok...
[sanei_pa4s2] sanei_pa4s2_readend: this means, I did not check it - it's
[sanei_pa4s2] sanei_pa4s2_readend: not my fault, if your PC burns down.
[sanei_pa4s2] sanei_pa4s2_readend: NIB mode readend
[sanei_pa4s2] pa4s2_readend_nib: end of reading sequence for fd 2
[sanei_pa4s2] sanei_pa4s2_readend: returning SANE_STATUS_GOOD
[sanei_pa4s2] sanei_pa4s2_open: could not find scanner
[sanei_pa4s2] sanei_pa4s2_open: reported ASIC id 0x77
[sanei_pa4s2] sanei_pa4s2_enable: called for fd 2 with value 0
[sanei_pa4s2] sanei_pa4s2_enable: disable port '0x3bc'
[sanei_pa4s2] pa4s2_disable: state restored
[sanei_pa4s2] sanei_pa4s2_enable: returning SANE_STATUS_GOOD
[sanei_pa4s2] sanei_pa4s2_open: closing port
[sanei_pa4s2] sanei_pa4s2_close: fd = 2
[sanei_pa4s2] sanei_pa4s2_close: freeing resources
[sanei_pa4s2] pa4s2_close: fd=2
[sanei_pa4s2] pa4s2_close: this is port '0x3bc'
[sanei_pa4s2] pa4s2_close: checking whether port is enabled
[sanei_pa4s2] pa4s2_close: trying to free io port
[sanei_pa4s2] pa4s2_close: marking port as unused
[sanei_pa4s2] pa4s2_close: returning SANE_STATUS_GOOD
[sanei_pa4s2] sanei_pa4s2_close: finished
[sanei_pa4s2] sanei_pa4s2_open: returning SANE_STATUS_INVAL
[mustek_pp] cis_attach: couldn't attach to `0x3bc' (Invalid argument)
[sanei_debug] Setting debug level of sanei_pa4s2 to 128.
[sanei_pa4s2] sanei_pa4s2_scsi_pp_open: interface called for the first time
[sanei_pa4s2] sanei_pa4s2_scsi_pp_open: called for device '/dev/scanner'
[sanei_pa4s2] sanei_pa4s2_scsi_pp_open: trying to connect to port
[sanei_pa4s2] pa4s2_open: trying to attach dev `/dev/scanner`
[sanei_pa4s2] pa4s2_init: static int first_time = 1
[sanei_pa4s2] pa4s2_init: called for the first time
[sanei_pa4s2] pa4s2_init: initializing libieee1284
[sanei_pa4s2] pa4s2_init: 3 ports reported by IEEE 1284 library
[sanei_pa4s2] pa4s2_init: port 0 is `0x278`
[sanei_pa4s2] pa4s2_init: port 1 is `0x378`
[sanei_pa4s2] pa4s2_init: port 2 is `0x3bc`
[sanei_pa4s2] pa4s2_init: allocating port list
[sanei_pa4s2] pa4s2_init: initialized successfully
[sanei_pa4s2] pa4s2_open: looking up port in list
[sanei_pa4s2] pa4s2_open: `/dev/scanner` is not a valid device name
[sanei_pa4s2] pa4s2_open: returning SANE_STATUS_INVAL
[sanei_pa4s2] sanei_pa4s2_scsi_pp_open: connection failed

No scanners were identified. If you were expecting something different,
check that the scanner is plugged in, turned on and detected by the
sane-find-scanner tool (if appropriate). Please read the documentation
which came with this software (README, FAQ, manpages).
[mustek_pp] sane_exit: all drivers unloaded

-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.2 (FreeBSD)
Comment: Using GnuPG with Mozilla - http://enigmail.mozdev.org

iD8DBQFEyRMmoqizRZ7rzU8RAvmCAJ9/hUH1yBR737vm0spbHCDdyePJ3gCgg8+3
BhitRlOXvzqsoy7OdazyfsA=
=/i65
-----END PGP SIGNATURE-----