[sane-devel] canon dr-9050c doesn't work

[m. allan noah]

Those are warnings from XSane, which has some programming errors. You
could contact the developer about those, or perhaps upgrade to a later
version and see if they are fixed.

The permissions issue is caused by udev or hal or whatever your distro
uses to allow access to hardware. It does not know about the newer
scanners in sane-backends. Try looking for a sane .fdi file in
/usr/share/hal or a sane rules file in /etc/udev/rules.d. Copy the
line for an existing scanner, and change it to match yours.

allan

On Mon, Dec 13, 2010 at 6:44 AM, Luigi Carbone <lg.carbone at gmail.com> wrote:
> Ok I solved the problem of the installation, now the scanner works with the
> following commands, but only if I start xsane as root. Omitting this,
> returns this error when I start xsane from a terminal
>
> (xsane:9913): Gtk-WARNING **: GtkSpinButton: setting an adjustment with
> non-zero page size is deprecated
>
> (xsane:9913): Gtk-WARNING **: GtkSpinButton: setting an adjustment with
> non-zero page size is deprecated
>
> (xsane:9913): Gtk-WARNING **: GtkSpinButton: setting an adjustment with
> non-zero page size is deprecated
>
> (xsane:9913): Gtk-WARNING **: GtkSpinButton: setting an adjustment with
> non-zero page size is deprecated
>
> (xsane:9913): Gtk-WARNING **: GtkSpinButton: setting an adjustment with
> non-zero page size is deprecated
>
> (xsane:9913): Gtk-WARNING **: GtkSpinButton: setting an adjustment with
> non-zero page size is deprecated
>
> (xsane:9913): Gtk-WARNING **: GtkSpinButton: setting an adjustment with
> non-zero page size is deprecated
>
> (xsane:9913): Gtk-WARNING **: GtkSpinButton: setting an adjustment with
> non-zero page size is deprecated
>
> (xsane:9913): Gtk-WARNING **: GtkSpinButton: setting an adjustment with
> non-zero page size is deprecated
>
> (xsane:9913): Gtk-WARNING **: GtkSpinButton: setting an adjustment with
> non-zero page size is deprecated
>
> (xsane:9913): Gtk-WARNING **: GtkSpinButton: setting an adjustment with
> non-zero page size is deprecated
>
> (xsane:9913): Gtk-WARNING **: GtkSpinButton: setting an adjustment with
> non-zero page size is deprecated
>
> (xsane:9913): Gtk-WARNING **: GtkSpinButton: setting an adjustment with
> non-zero page size is deprecated
>
> (xsane:9913): Gtk-WARNING **: GtkSpinButton: setting an adjustment with
> non-zero page size is deprecated
>
> (xsane:9913): Gtk-WARNING **: GtkSpinButton: setting an adjustment with
> non-zero page size is deprecated
>
> (xsane:9913): Gtk-WARNING **: GtkSpinButton: setting an adjustment with
> non-zero page size is deprecated
>
> (xsane:9913): Gtk-WARNING **: GtkSpinButton: setting an adjustment with
> non-zero page size is deprecated
>
> (xsane:9913): Gtk-WARNING **: GtkSpinButton: setting an adjustment with
> non-zero page size is deprecated
>
> (xsane:9913): Gtk-WARNING **: GtkSpinButton: setting an adjustment with
> non-zero page size is deprecated
>
> (xsane:9913): Gtk-WARNING **: GtkSpinButton: setting an adjustment with
> non-zero page size is deprecated
>
> tks for help
>
> Il 22/11/2010 12:33, m. allan noah ha scritto:
>>
>> "/usr/local/etc/sane.d/dll.d"
>>
>> you have two copies of sane installed, and the one in /usr/local is
>> being used, but it has no config files. I would remove that copy, and
>> re-configure with the proper arguments to overwrite your existing
>> copy. Something like:
>>
>> ./configure --prefix=/usr --sysconfdir=/etc
>> make
>> make install
>>
>> allan
>>
>> On Mon, Nov 22, 2010 at 2:30 AM, Luigi Carbone<lg.carbone at gmail.com>
>>  wrote:
>>>
>>> In /etc/sane.d/.dll.conf "canon_dr" is listed,
>>>
>>> The result of command SANE_DEBUG_DLL=255 scanimage -L 2>9050.log on
>>> terminal
>>> is
>>>
>>> sudo SANE_DEBUG_DLL=255 scanimage -L 2>  9050.log
>>> [sanei_debug] Setting debug level of dll to 255.
>>> [dll] sane_init: SANE dll backend version 1.0.12 from sane-backends
>>> 1.0.21
>>> [dll] sane_init/read_dlld: processing /usr/local/etc/sane.d/dll.d ...
>>> [dll] sane_init/read_dlld: done.
>>> [dll] sane_init/read_config: Couldn't open config file (dll.conf): No
>>> such
>>> file or directory
>>> [dll] sane_get_devices
>>> [dll] sane_get_devices: found 0 devices
>>> [dll] sane_exit: exiting
>>> [dll] sane_exit: finished
>>>
>>> but the 9050.log is attach.
>>>
>>> TKS
>>>
>>> Il 19/11/2010 14:26, m. allan noah ha scritto:
>>>>
>>>> The canon_dr backend is not enabled. check /etc/sane.d/dll.conf, and
>>>> make sure 'canon_dr' is listed there.
>>>>
>>>> If it is listed, then try this:
>>>>
>>>> SANE_DEBUG_DLL=255 scanimage -L 2>9050.log
>>>>
>>>> and send that log.
>>>>
>>>> allan
>>>>
>>>> On Fri, Nov 19, 2010 at 7:56 AM, Luigi Carbone<lg.carbone at gmail.com>
>>>>  wrote:
>>>>>
>>>>> Mmh, it's same.
>>>>>
>>>>> The log file is attach.
>>>>>
>>>>> Luigi
>>>>>
>>>>> Il 19/11/2010 13:33, m. allan noah ha scritto:
>>>>>>
>>>>>> Ok- as root, run this:
>>>>>>
>>>>>> SANE_DEBUG_CANON_DR=30 scanimage -L 2>9050.log
>>>>>>
>>>>>> then send 9050.log to the list.
>>>>>>
>>>>>> allan
>>>>>>
>>>>>> On Fri, Nov 19, 2010 at 2:03 AM, Luigi Carbone<lg.carbone at gmail.com>
>>>>>>  wrote:
>>>>>>>
>>>>>>> With a privileges root, this is the result
>>>>>>>
>>>>>>> No scanners were identified. If you were expecting something
>>>>>>> different,
>>>>>>> check that the scanner is plugged in, turned on and detected by the
>>>>>>> sane-find-scanner tool (if appropriate). Please read the
>>>>>>> documentation
>>>>>>> which came with this software (README, FAQ, manpages).
>>>>>>>
>>>>>>> :(
>>>>>>>
>>>>>>> Il 18/11/2010 14:20, m. allan noah ha scritto:
>>>>>>>>
>>>>>>>> as root, run the following command, and send output to us:
>>>>>>>>
>>>>>>>> scanimage -L
>>>>>>>>
>>>>>>>> allan
>>>>>>>>
>>>>>>>> On Thu, Nov 18, 2010 at 7:57 AM, Luigi Carbone<lg.carbone at gmail.com>
>>>>>>>>  wrote:
>>>>>>>>>
>>>>>>>>> Hi all,
>>>>>>>>> I have problem with scanner canon dr-9050C, i have ubuntu 10.04 and
>>>>>>>>> installated driver san version 1.0.21.
>>>>>>>>>
>>>>>>>>> I have configured file canon_dr.conf so
>>>>>>>>> # DR-9050C
>>>>>>>>> usb 0x1083 0x1622
>>>>>>>>>
>>>>>>>>> the command lsusb returns
>>>>>>>>>
>>>>>>>>> Bus 008 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
>>>>>>>>> Bus 007 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
>>>>>>>>> Bus 006 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
>>>>>>>>> Bus 005 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
>>>>>>>>> Bus 004 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
>>>>>>>>> Bus 003 Device 002: ID 046d:c505 Logitech, Inc. Cordless
>>>>>>>>> Mouse+Keyboard
>>>>>>>>> Receiver
>>>>>>>>> Bus 003 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
>>>>>>>>> Bus 002 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
>>>>>>>>> Bus 001 Device 004: ID 152e:2507 LG (HLDS)
>>>>>>>>> Bus 001 Device 003: ID 1083:1622 Canon Electronics, Inc.
>>>>>>>>> Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
>>>>>>>>>
>>>>>>>>> the scanner is visible to the system...
>>>>>>>>>
>>>>>>>>> Help me.
>>>>>>>>> --
>>>>>>>
>>>>>
>
>
>
> --
> Luigi Carbone
> ----------------------
> Owner @ http://www.ingenioweb.it
> Web Designer @ www.consulenti-ict.it
> CV: http://www.linkedin.com/in/carboneluigi
> Skype: corsaro832
> Cell: 340 32 15 783
>



-- 
"The truth is an offense, but not a sin"