[sane-devel] Scanimage only detects Canon LiDE20 once

[James Fowkes]

Further information:

I ran "SANE_DEBUG_PLUSTEK scanimage -L" and got:

james at jamespc:~$ SANE_DEBUG_PLUSTEK=20 scanimage -L
[sanei_debug] Setting debug level of plustek to 20.
[plustek] Plustek backend V0.52-9, part of sane-backends 1.0.22
[plustek] Retrieving all supported and conntected devices
[plustek] Checking for 0x07b3-0x0010
[plustek] Checking for 0x07b3-0x0011
[plustek] Checking for 0x07b3-0x0013
[plustek] Checking for 0x07b3-0x0017
[plustek] Checking for 0x07b3-0x0015
[plustek] Checking for 0x07b3-0x0015
[plustek] Checking for 0x07b3-0x0017
[plustek] Checking for 0x07b3-0x0013
[plustek] Checking for 0x07b3-0x0011
[plustek] Checking for 0x07b3-0x0010
[plustek] Checking for 0x07b3-0x0014
[plustek] Checking for 0x07b3-0x0014
[plustek] Checking for 0x07b3-0x0016
[plustek] Checking for 0x07b3-0x0017
[plustek] Checking for 0x07b3-0x0017
[plustek] Checking for 0x07b3-0x0007
[plustek] Checking for 0x07b3-0x000f
[plustek] Checking for 0x07b3-0x000f
[plustek] Checking for 0x07b3-0x0005
[plustek] Checking for 0x07b3-0x0014
[plustek] Checking for 0x07b3-0x0012
[plustek] Checking for 0x0400-0x1000
[plustek] Checking for 0x0400-0x1001
[plustek] Checking for 0x0400-0x1001
[plustek] Checking for 0x0458-0x2007
[plustek] Checking for 0x0458-0x2008
[plustek] Checking for 0x0458-0x2009
[plustek] Checking for 0x0458-0x2013
[plustek] Checking for 0x0458-0x2015
[plustek] Checking for 0x0458-0x2016
[plustek] Checking for 0x03f0-0x0505
[plustek] Checking for 0x03f0-0x0605
[plustek] Checking for 0x04b8-0x010f
[plustek] Checking for 0x04b8-0x011d
[plustek] Checking for 0x1606-0x0050
[plustek] Checking for 0x1606-0x0060
[plustek] Checking for 0x1606-0x0160
[plustek] Checking for 0x049f-0x001a
[plustek] Checking for 0x04a9-0x2206
[plustek] Checking for 0x04a9-0x2207
[plustek] Checking for 0x04a9-0x2208
[plustek] Checking for 0x04a9-0x220d
[plustek] Checking for 0x04a9-0x220e
[plustek] Checking for 0x04a9-0x2220
[plustek] Checking for 0x0a82-0x4600
[plustek] Checking for 0x0a82-0x6620
[plustek] Checking for 0x04a7-0x0427
[plustek] Checking for 0x0a53-0x1000
[plustek] Available and supported devices:
[plustek] Device: >libusb:002:004< - 0x04a9x0x220d
[plustek] ># Plustek-SANE Backend configuration file<
[plustek] ># For use with LM9831/2/3 based USB scanners<
[plustek] >#<
[plustek] ><
[plustek] ># each device needs at least two lines:<
[plustek] ># - [usb] vendor-ID and product-ID<
[plustek] ># - device devicename<
[plustek] ># i.e. for Plustek (0x07B3) UT12/16/24 (0x0017)<
[plustek] ># [usb] 0x07B3 0x0017<
[plustek] ># device /dev/usbscanner<
[plustek] ># or<
[plustek] ># device libusb:bbb:ddd<
[plustek] ># where bbb is the busnumber and ddd the device number<
[plustek] ># make sure that your user has access to /proc/bus/usb/bbb/ddd<
[plustek] >#<
[plustek] ># additionally you can specify some options<
[plustek] ># warmup, lOffOnEnd, lampOff<
[plustek] >#<
[plustek] ># For autodetection use<
[plustek] ># [usb]<
[plustek] ># device /dev/usbscanner<
[plustek] >#<
[plustek] ># or simply<
[plustek] ># [usb]<
[plustek] >#<
[plustek] ># or if you want a specific device but you have no idea about
the<
[plustek] ># device node or you use libusb, simply set vendor- and
product-ID<
[plustek] ># [usb] 0x07B3 0x0017<
[plustek] ># device auto<
[plustek] >#<
[plustek] ># NOTE: autodetection is safe, as it uses the info it got<
[plustek] >#       from the USB subsystem. If you're not using the<
[plustek] >#       autodetection, you MUST have attached that device<
[plustek] >#       at your USB-port, that you have specified...<
[plustek] >#<
[plustek] ><
[plustek] >[usb]<
[plustek] next device uses autodetection
[plustek] ... next device
[plustek] ><
[plustek] >#<
[plustek] ># options for the previous USB entry<
[plustek] >#<
[plustek] ># switch lamp off after xxx secs, 0 disables the feature<
[plustek] ># (can also be set via frontend)<
[plustek] >option lampOff 300<
[plustek] Decoding option >lampOff<
[plustek] ><
[plustek] ># warmup period in seconds, 0 means no warmup, -1 means
auto-warmup<
[plustek] ># (can also be set via frontend)<
[plustek] >option warmup -1<
[plustek] Decoding option >warmup<
[plustek] ><
[plustek] ># 0 means leave lamp-status untouched, not 0 means switch off<
[plustek] ># on sane_close<
[plustek] ># (can also be set via frontend)<
[plustek] >option lOffOnEnd 1<
[plustek] Decoding option >lOffOnEnd<
[plustek] ><
[plustek] >#<
[plustek] ># options to tweak the image start-position<
[plustek] ># (WARNING: there's no internal range check!!!)<
[plustek] >#<
[plustek] ># for the normal scan area<
[plustek] >#<
[plustek] >option posOffX 0<
[plustek] Decoding option >posOffX<
[plustek] >option posOffY 0<
[plustek] Decoding option >posOffY<
[plustek] ><
[plustek] ># for transparencies<
[plustek] >option tpaOffX 0<
[plustek] Decoding option >tpaOffX<
[plustek] >option tpaOffY 0<
[plustek] Decoding option >tpaOffY<
[plustek] ><
[plustek] ># for negatives<
[plustek] >option negOffX 0<
[plustek] Decoding option >negOffX<
[plustek] >option negOffY 0<
[plustek] Decoding option >negOffY<
[plustek] ><
[plustek] >#<
[plustek] ># for setting the calibration strip position<
[plustek] ># (WARNING: there's no internal range check!!!)<
[plustek] ># -1 means use built in<
[plustek] ># (can also be set via frontend)<
[plustek] >option posShadingY -1<
[plustek] Decoding option >posShadingY<
[plustek] >option tpaShadingY -1<
[plustek] Decoding option >tpaShadingY<
[plustek] >option negShadingY -1<
[plustek] Decoding option >negShadingY<
[plustek] ><
[plustek] >#<
[plustek] ># to invert the negatives, 0 disables the feature<
[plustek] >#<
[plustek] >option invertNegatives 0<
[plustek] Decoding option >invertNegatives<
[plustek] ><
[plustek] >#<
[plustek] ># to disable the internal sensor speedup function,<
[plustek] ># 1 disables the feature<
[plustek] >#<
[plustek] >option disableSpeedup 0<
[plustek] Decoding option >disableSpeedup<
[plustek] ><
[plustek] >#<
[plustek] ># to save/restore coarse calibration data<
[plustek] ># (can also be set via frontend)<
[plustek] >option cacheCalData 0<
[plustek] Decoding option >cacheCalData<
[plustek] ><
[plustek] >#<
[plustek] ># use alternate calibration routines<
[plustek] >#<
[plustek] >option altCalibration 0<
[plustek] Decoding option >altCalibration<
[plustek] ><
[plustek] >#<
[plustek] ># for skipping whole calibration step<
[plustek] >#<
[plustek] >option skipCalibration 0<
[plustek] Decoding option >skipCalibration<
[plustek] ><
[plustek] >#<
[plustek] ># for skipping entire fine calibration step<
[plustek] ># coarse calibration is done<
[plustek] >#<
[plustek] >option skipFine 0<
[plustek] Decoding option >skipFine<
[plustek] ><
[plustek] >#<
[plustek] ># discard the result of the fine white calibration<
[plustek] >#<
[plustek] >option skipFineWhite 0<
[plustek] Decoding option >skipFineWhite<
[plustek] ><
[plustek] >#<
[plustek] ># some scanners have a dark calibration strip, in<
[plustek] ># general this one should be used for calibration.<
[plustek] ># As this could cause some trouble, this option<
[plustek] ># overrides that and the dark calibration will be<
[plustek] ># done by switching the lamp off<
[plustek] >#<
[plustek] >option skipDarkStrip 0<
[plustek] Decoding option >skipDarkStrip<
[plustek] ><
[plustek] ># for replacing the gain values found during coarse<
[plustek] ># calibration<
[plustek] ># (can also be set via frontend)<
[plustek] >option red_gain   -1<
[plustek] Decoding option >red_gain<
[plustek] >option green_gain -1<
[plustek] Decoding option >green_gain<
[plustek] >option blue_gain  -1<
[plustek] Decoding option >blue_gain<
[plustek] ><
[plustek] ># for replacing the offset values found during coarse<
[plustek] ># calibration<
[plustek] ># (can also be set via frontend)<
[plustek] >option red_offset   -1<
[plustek] Decoding option >red_offset<
[plustek] >option green_offset -1<
[plustek] Decoding option >green_offset<
[plustek] >option blue_offset  -1<
[plustek] Decoding option >blue_offset<
[plustek] ><
[plustek] >#<
[plustek] ># for replacing the default lampoff settings, this<
[plustek] ># works only for CIS devices like CanoScan LiDE20<
[plustek] ># (can also be set via frontend)<
[plustek] >option red_lampoff   -1<
[plustek] Decoding option >red_lampoff<
[plustek] >option green_lampoff -1<
[plustek] Decoding option >green_lampoff<
[plustek] >option blue_lampoff  -1<
[plustek] Decoding option >blue_lampoff<
[plustek] ><
[plustek] >#<
[plustek] ># for adjusting the default gamma values<
[plustek] ># (can also be set via frontend)<
[plustek] >option redGamma         1.0<
[plustek] Decoding option >redGamma<
[plustek] >option greenGamma       1.0<
[plustek] Decoding option >greenGamma<
[plustek] >option blueGamma        1.0<
[plustek] Decoding option >blueGamma<
[plustek] >option grayGamma        1.0<
[plustek] Decoding option >grayGamma<
[plustek] ><
[plustek] >#<
[plustek] ># to enable TPA (EPSON or UMAX, if autodetection fails)<
[plustek] ># 0 means default behaviour as specified in the internal tables<
[plustek] ># 1 means enable (needed for UMAX 3450)<
[plustek] >option enableTPA 0<
[plustek] Decoding option >enableTPA<
[plustek] ><
[plustek] >#<
[plustek] ># model override functionality, currently only available for<
[plustek] ># Mustek devices, using NSCs' vendor ID: 0x0400 and<
[plustek] ># also their product ID: 0x1000 (LM9831) 0x1001 (LM9832)<
[plustek] >#<
[plustek] ># mov/PID    |    0x1000   |   0x1001<
[plustek] ># ---------------------------------------<
[plustek] ># 0 (default)| BearPaw1200 | BearPaw 2400<
[plustek] ># 1          |   ignored   | BearPaw 1200<
[plustek] >#<
[plustek] >option mov 0<
[plustek] Decoding option >mov<
[plustek] ><
[plustek] >#<
[plustek] ># and of course the device-name<
[plustek] >#<
[plustek] ># device /dev/usbscanner<
[plustek] >device auto<
[plustek] Decoding device name >auto<
[plustek] ><
[plustek] >#<
[plustek] ># to define a new device, start with a new section:<
[plustek] ># [usb]<
[plustek] >#<
[plustek] attach (auto, 0xbfd7509c, (nil))
[plustek] Device configuration:
[plustek] device name  : >auto<
[plustek] USB-ID       : ><
[plustek] model ovr.   : 0
[plustek] warmup       : -1s
[plustek] lampOff      : 300
[plustek] lampOffOnEnd : yes
[plustek] cacheCalData : no
[plustek] altCalibrate : no
[plustek] skipCalibr.  : no
[plustek] skipFine     : no
[plustek] skipFineWhite: no
[plustek] skipDarkStrip: no
[plustek] incDarkTarget: yes
[plustek] invertNegs.  : no
[plustek] dis.Speedup  : no
[plustek] pos_x        : 0
[plustek] pos_y        : 0
[plustek] pos_shading_y: -1
[plustek] neg_x        : 0
[plustek] neg_y        : 0
[plustek] neg_shading_y: -1
[plustek] tpa_x        : 0
[plustek] tpa_y        : 0
[plustek] tpa_shading_y: -1
[plustek] red gain     : -1
[plustek] green gain   : -1
[plustek] blue gain    : -1
[plustek] red offset   : -1
[plustek] green offset : -1
[plustek] blue offset  : -1
[plustek] red lampoff  : -1
[plustek] green lampoff: -1
[plustek] blue lampoff : -1
[plustek] red Gamma    : 1.00
[plustek] green Gamma  : 1.00
[plustek] blue Gamma   : 1.00
[plustek] gray Gamma   : 1.00
[plustek] ---------------------
[plustek] usbDev_open(auto,) - 0x93e81e8
[plustek] Vendor ID=0x04A9, Product ID=0x220D
[plustek] usbio_DetectLM983x
[plustek] usbio_DetectLM983x: found LM9832/3
[plustek] Detected vendor & product ID: 0x04A9-0x220D
[plustek] Device description for >0x04A9-0x220D< found.
[plustek] usb_initDev(41,0x04a9,-1)
[plustek] Device WAF  : 0x00004002
[plustek] Transferrate: 1000000 Bytes/s
[plustek] Device Flags: 0x00000000
[plustek] Vendor adjusted to: >Canon<
[plustek] LAMP-STATUS: 0x00000000 (off)
[plustek] RESETTING REGISTERS(-1) - 0x80
[plustek] SETTING THE MISC I/Os
[plustek] MISC I/O after RESET: 0x66, 0x16, 0x91
[plustek] Scanner not ready!!!
[plustek] Calibration file-names set to:
[plustek] >/home/james/.sane/Canon_CanoScan_N670U_N676U_LiDE20-coarse.cal<
[plustek] >/home/james/.sane/Canon_CanoScan_N670U_N676U_LiDE20-fine.cal<
[plustek] usb_SetScanParameters()
[plustek] Scanner not ready!!!
[plustek] UIO error
[plustek] usbDev_getCaps()
[plustek] Scanner information:
[plustek] Vendor : Canon
[plustek] Model  : CanoScan N670U/N676U/LiDE20
[plustek] Flags  : 0x00000000
[plustek] drvclose()
[plustek] usbDev_stopScan()
[plustek] usbDev_ScanEnd(), start=0, park=0
[plustek] UIO error
[plustek] usbDev_close()
[plustek] attach: model = >CanoScan N670U/N676U/LiDE20<
[plustek] sane_get_devices (0xbfd7721c, 0)
device `plustek:libusb:002:004' is a Canon CanoScan N670U/N676U/LiDE20
flatbed scanner
[plustek] sane_exit
[plustek] Shutdown called (dev->fd=-1, libusb:002:004)
[plustek] Lamp-Timer stopped

Also, I have no entries in /proc/bus/usb, but I don't believe this is an
issue. Please correct me if I'm wrong.

James
-------------- next part --------------
An HTML attachment was scrubbed...
URL: <http://lists.alioth.debian.org/pipermail/sane-devel/attachments/20120628/ed0e317e/attachment-0001.html>