[Nut-upsuser] Problem with APC SMART UPS 1000 (USB)

[Sergey]

Hi friends.

Package: nut
Version: 2.4.1-1
Depends: libusb, openssl, neon, libgd, net-snmp
Status: install user installed
Section: admin
Architecture: mipsel
maintainer: NSLU2 Linux <nslu2-linux at yahoogroups.com>
MD5Sum: c8c55a6021fea2b5f194ce4623eb2dfe
Size: 1246363
Filename: nut_2.4.1-1_mipsel.ipk
Source: http://eu1.networkupstools.org/source/2.4/nut-2.4.1.tar.gz
Description: Network UPS tools.
------------------------------------------
Startup log:
Jul  6 22:00:19 rc.unslung: start service /opt/etc/init.d/S50ups
Jul  6 22:00:21 usbhid-ups[170]: Startup successful
Jul  6 22:00:21 upsd[173]: /opt/etc/upsd.conf is world readable
Jul  6 22:00:21 upsd[173]: listening on 127.0.0.1 port 3493
Jul  6 22:00:21 upsd[173]: listening on 192.168.1.1 port 3493
Jul  6 22:00:21 upsd[173]: /opt/var/state/ups is world readable
Jul  6 22:00:21 upsd[173]: Connected to UPS [ups]: usbhid-ups-ups
Jul  6 22:00:21 upsd[173]: /opt/etc/upsd.users is world readable
Jul  6 22:00:21 upsd[174]: Startup successful
------------------------------------------
Ok
------------------------------------------
$upsc usb
battery.charge: 100
battery.charge.low: 10
battery.charge.warning: 50
battery.mfr.date: 2007/11/18
battery.runtime: 2940
battery.runtime.low: 120
battery.temperature: 34.2
battery.type: PbAc
battery.voltage: 27.3
battery.voltage.nominal: 24.0
driver.name: usbhid-ups
driver.parameter.pollfreq: 30
driver.parameter.pollinterval: 2
driver.parameter.port: /dev/usb/hiddev0
driver.version: 2.4.1
driver.version.data: APC HID 0.93
driver.version.internal: 0.34
input.voltage: 216.0
output.voltage: 216.0
output.voltage.nominal: 220.0
ups.beeper.status: disabled
ups.delay.shutdown: 20
ups.firmware: 652.18.I
ups.firmware.aux: 7.3
ups.load: 26.0
ups.mfr: American Power Conversion
ups.mfr.date: 2007/11/18
ups.model: Smart-UPS 1000
ups.productid: 0002
ups.serial: AS0746224745
ups.status: OL
ups.test.result: No test initiated
ups.timer.reboot: -1
ups.timer.shutdown: -1
ups.vendorid: 051d
------------------------------------------
Ok.
But, to switch off the electric power
After 20 min:
------------------------------------------
$upsc usb
..skip...
battery.charge: 100
battery.temperature: 36.8
battery.voltage: 23.9
input.voltage: 0.0
output.voltage: 220.4
ups.load: 24.7
ups.status: OL
...skip...
------------------------------------------
The ups.status and battery.charger have not changed the value.
battery.voltage, ups.load, battery.temperature adequately react.

After restoration electric power:
------------------------------------------
$upsc usb
..skip...
battery.charge: 52
battery.temperature: 39.1
battery.voltage: 26.2
input.voltage: 217.4
output.voltage: 217.4
ups.load: 26.6
ups.status: OL
...skip...
------------------------------------------
The battery.charge and input.voltage show correct values.

P.S. Probably the driver not truly reads out a condition my ups.