[Nut-upsuser] Eaton NV 1000H in nut's hardware compatibility list

[Vitor Choi Feitosa]

Here's what you asked for:

$ upsc eaton
battery.charge: 90.0
battery.voltage: 13.30
battery.voltage.nominal: 12.0
driver.name: megatec_usb
driver.parameter.pollinterval: 2
driver.parameter.port: auto
driver.version: 2.2.1-
driver.version.internal: 1.5.13
input.frequency: 59.9
input.voltage: 216.6
input.voltage.fault: 216.6
input.voltage.maximum: 222.7
input.voltage.minimum: 206.0
output.voltage: 216.6
output.voltage.nominal: 230.0
ups.beeper.status: enabled
ups.delay.shutdown: 0
ups.delay.start: 2
ups.load: 21.0
ups.mfr: unknown
ups.model: unknown
ups.serial: unknown
ups.status: OL
ups.temperature: 25.0


$ upscmd -l eaton
Instant commands supported on UPS [eaton]:

test.battery.start.deep - Start a deep battery test
test.battery.start - Start a battery test
test.battery.stop - Stop the battery test
shutdown.return - Turn off the load and return when power is back
shutdown.stayoff - Turn off the load and remain off
shutdown.stop - Stop a shutdown in progress
load.on - Turn on the load immediately
load.off - Turn off the load immediately
reset.input.minmax - Reset minimum and maximum input voltage status
reset.watchdog - Reset watchdog timer
beeper.toggle - Toggle the UPS beeper


upsmon wall message
Broadcast Message from nut at cctv

        (somewhere) at 12:15
...


UPS eaton at localhost on battery


and finally, a syslog snippet of the system shutting down:
Sep 14 12:33:20 cctv upsd[6192]: Connection from 127.0.0.1
Sep 14 12:33:20 cctv upsd[6192]: Client on 127.0.0.1 logged out
Sep 14 12:33:21 cctv upsmon[6200]: UPS eaton at localhost battery is low
Sep 14 12:33:21 cctv upsd[6192]: Client local_mon at 127.0.0.1 set FSD on UPS
[eaton]
Sep 14 12:33:21 cctv upsmon[6200]: Executing automatic power-fail shutdown
Sep 14 12:33:21 cctv upsmon[6200]: Auto logout and shutdown proceeding
Sep 14 12:33:22 cctv upsd[6192]: Connection from 127.0.0.1
Sep 14 12:33:22 cctv upsd[6192]: Client on 127.0.0.1 logged out
Sep 14 12:33:24 cctv upsd[6192]: Connection from 127.0.0.1
Sep 14 12:33:24 cctv upsd[6192]: Client on 127.0.0.1 logged out
Sep 14 12:33:26 cctv upsd[6192]: Host 127.0.0.1 disconnected (read failure)
Sep 14 12:33:26 cctv init: tty4 main process (4901) killed by TERM signal
Sep 14 12:33:26 cctv init: tty5 main process (4902) killed by TERM signal
Sep 14 12:33:26 cctv init: tty2 main process (4904) killed by TERM signal
Sep 14 12:33:26 cctv init: tty3 main process (4906) killed by TERM signal
Sep 14 12:33:26 cctv init: tty1 main process (6445) killed by TERM signal
Sep 14 12:33:26 cctv init: tty6 main process (4908) killed by TERM signal
Sep 14 12:33:28 cctv avahi-daemon[5388]: Got SIGTERM, quitting.


Tell me if you need anything else.

Vitor.


2009/9/14 Arnaud Quette <ArnaudQuette at eaton.com>

> Le samedi 12 septembre 2009 à 01:59 -0300, Vitor Choi Feitosa a écrit :
> > Hi Arnaud,
>
> Hi Vitor,
>
> > I found your email on the contact page and since you seem to work for
> > Eaton and is involved in the NUT community I think you're the right
> > person to contact.
> >
> > I've got an Eaton NV 1000H and just installed it here. Before NUT
> > configuration I've checked the HCL for my UPS and didn't find it
> > there. After trying a few drivers I found that the megatec_usb just
> > works for this model.
> >
> > So.. I thought you could arrange to get this model on the HCL. Will
> > you do it?
>
> sure.
>
> can you just post me the output of:
> - upsc,
> - upscmd,
> - upsrw.
>
> Have you tested a standard shutdown (ie OB until LB, or calling "upsmon
> -c fsd")?
>
> thanks for your report.
> Arnaud
> --
> Linux/Unix Expert R&D - Eaton - http://www.eaton.com/mgeops
> Network UPS Tools (NUT) Project Leader - http://www.networkupstools.org/
> Debian Developer - http://www.debian.org
> Free Software Developer - http://arnaud.quette.free.fr/
>
> --------------------------------------------------------------------------
> Eaton Power Quality SA ~ Siège social:
> 110 rue Blaise Pascal,
> 38 334 Saint Ismier, France ~ Lieu d'enregistrement au registre du
> commerce: Grenoble ~ Numéro d'enregistrement:
> 302 636 303  ~ Capital social souscrit et liberé:
> 703'802.75 EUR
>



-- 
--
Vitor Choi Feitosa <vchoi at vchoi.org>
+55 61 7814-9719
-------------- next part --------------
An HTML attachment was scrubbed...
URL: <http://lists.alioth.debian.org/pipermail/nut-upsuser/attachments/20090915/c4ee93c1/attachment.htm>