[sane-devel] Re: HP C2502A 3503

[Peter Kirchgessner]

Hi,

just two short questions for the beginning: What's your kernel version 
and your SCSI card ?

--Peter

O-Zone wrote:

> On Tuesday 28 May 2002 20:23, Henning Meier-Geinitz wrote:
> 
>>Hi,
>>
>>On Tue, May 28, 2002 at 06:13:19PM +0200, O-Zone wrote:
>>
>>>i'll try to install my SCSI scanner, an HP ScanJet 4C.
>>>If i launch sane-find-scanner i have this reply:
>>>
>>Which version of SANE?
>>
> 
> 1.0.8
> 
> 
>>>sane-find-scanner: found SCSI processor "HP C2502A 3503" at device
>>>/dev/sg0 sane-find-scanner: found SCSI processor "HP C2502A 3503" at
>>>device /dev/sga
>>>
>>>i've created a link /dev/scanner but if i try to launch 'scanimage
>>>--list-devices' it returns that "No scanners were identified" !
>>>
>>Try
>>
>>SANE_DEBUG_HP=255 scanimage -L
>>
>>You should get some debug output that may give more information on
>>what is going on.
>>
> 
> Here the output:
> 
> [sanei_debug] Setting debug level of hp to 255.
> [hp] sane_init called
> [hp] sane_init will finish with Success
> [hp] sane_get_devices called
> [hp] hp_read_config: hp backend v0.95 starts reading config file
> [hp] hp_read_config: processing line <scsi HP>
> [hp] hp_read_config: processing line </dev/sga>
> [hp] hp_read_config: attach scsi HP
> [hp] hp_get_dev: New device /dev/sg0, connect-scsi, scsi-request=1
> [hp] sanei_hp_device_new: /dev/sg0
> [hp] scsi_inquire: sending INQUIRE
> [hp] scsi_new: sending TEST_UNIT_READY
> [hp] scsi_flush: writing 2 bytes:
> [hp]  0x0000  1B 45                                            .E
> [hp] scsi_flush: writing 7 bytes:
> [hp]  0x0000  1B 2A 73 32 35 37 45                             .*s257E
> [hp] scl_inq: read failed (Error during device I/O)
> [hp] scl_errcheck: Can't read SCL error stack: Error during device I/O
> [hp] sanei_hp_device_new: SCL reset failed
> [hp] scsi_close: closing fd 5
> [hp] hp_read_config: processing line <option connect-scsi>
> [hp] hp_read_config: attach /dev/sga
> [hp] hp_get_dev: New device /dev/sga, connect-scsi, scsi-request=1
> [hp] sanei_hp_device_new: /dev/sga
> [hp] scsi_inquire: sending INQUIRE
> [hp] scsi_new: sending TEST_UNIT_READY
> [hp] scsi_flush: writing 2 bytes:
> [hp]  0x0000  1B 45                                            .E
> [hp] scsi_flush: writing 7 bytes:
> [hp]  0x0000  1B 2A 73 32 35 37 45                             .*s257E
> [hp] scl_inq: read failed (Error during device I/O)
> [hp] scl_errcheck: Can't read SCL error stack: Error during device I/O
> [hp] sanei_hp_device_new: SCL reset failed
> [hp] scsi_close: closing fd 4
> [hp] sane_get_devices will finish with Success
> [hp] sane_exit called
> [hp] sane_exit will finish
> 
> No scanners were identified. If you were expecting something different,
> check that the scanner is plugged in, turned on and detected by the
> sane-find-scanner tool (if appropriate). Please read the documentation
> which came with this software (README, FAQ, manpages).
> 
> And now ? ...
> 
> ----
> 
> 
> 
> _______________________________________________
> Sane-devel mailing list
> Sane-devel@www.mostang.com
> http://www.mostang.com/mailman/listinfo/sane-devel
> 
> 


-- 
Peter Kirchgessner
http://www.kirchgessner.net
mailto:peter@kirchgessner.net