[sane-devel] sane-find-scanner finds multiple scanners

[Ray Curtis]

>>>>> "cn" == Carsten Neumann <deltor at snafu.de> writes:

    cn> Hi, Johan,
    cn> you've missed to tell what your problems actually are!
    cn> I don't see any problem why you can't use your scanner.
    cn> But you haven't told that you cannot use it.
    cn> What are the errors you get, if there are any?

    cn> 	Carsten


I think from looking at the listing below it is pretty obvious that
the scsi card is detecting muliple scanners, at ID 1 Lun 00-07.
Not being familiar with this scsi card I can't really help much
except the suggest moving the ID from 1 to maybe 4 or 5. The lower
scsi ID's are usually used for hard drives.






    cn> On Mon, 06 May 2002, Johan Wehtje wrote:
    >> have read the docs as well as the SCSI 2.4 how to but am still none the 
    >> wiser as to why I get the following output from sane-find-scanner
    >> ===========================================
    >> sane-find-scanner: found SCSI scanner " Scanner 1.40" at device /dev/scanner
    >> sane-find-scanner: found SCSI scanner " Scanner 1.40" at device /dev/sg1
    >> sane-find-scanner: found SCSI scanner " Scanner 1.40" at device /dev/sg2
    >> sane-find-scanner: found SCSI scanner " Scanner 1.40" at device /dev/sg3
    >> sane-find-scanner: found SCSI scanner " Scanner 1.40" at device /dev/sg4
    >> sane-find-scanner: found SCSI scanner " Scanner 1.40" at device /dev/sg5
    >> sane-find-scanner: found SCSI scanner " Scanner 1.40" at device /dev/sg6
    >> sane-find-scanner: found SCSI scanner " Scanner 1.40" at device /dev/sg7
    >> sane-find-scanner: found SCSI scanner " Scanner 1.40" at device /dev/sg8
    >> sane-find-scanner: found SCSI scanner " Scanner 1.40" at device /dev/sgb
    >> sane-find-scanner: found SCSI scanner " Scanner 1.40" at device /dev/sgc
    >> sane-find-scanner: found SCSI scanner " Scanner 1.40" at device /dev/sgd
    >> sane-find-scanner: found SCSI scanner " Scanner 1.40" at device /dev/sge
    >> sane-find-scanner: found SCSI scanner " Scanner 1.40" at device /dev/sgf
    >> sane-find-scanner: found SCSI scanner " Scanner 1.40" at device /dev/sgg
    >> sane-find-scanner: found SCSI scanner " Scanner 1.40" at device /dev/sgh
    >> sane-find-scanner: found SCSI scanner " Scanner 1.40" at device /dev/sgi
    >> ======================================================
    >> I only have one scanner , microtek e3 connected to a adpaptec 1524 scsi card 
    >> (shipped with scanner). The aha152x scsi driver is loaded as a module. The 
    >> kernel is 2.4.18. The correct irq and io are passed as params to the module. 
    >> The system is a PII 400 MHZ , Asus MBrd , 128 mb RAM, Pheonix BIOS. I have an 
    >> older Zip 100 disk (parralell) that is loaded as a module and sits at sda4. I 
    >> have my own script for loading the zip as I need to modprobe lp before I do, 
    >> then modprobe ppa.
    >> I get the same result even if I don't load the zip and lp modules but only 
    >> prob the aha152x module manually.
    >> I am probably missing something really simple here but I can't see what it is 
    >> so would appreciate some help as i have been fiddling with thsi for the past 
    >> few weeks trying to get it to work.
    >> BTW this is a dual boot system (win 98 SE) and the scanner works just fine in 
    >> Windows , but i would really like to skip booting into windows every time i 
    >> want to use the scanner.
    >> anf FYI the out of "cat /proc/scsi/scsi" is below:
    >> ==================================
    >> Attached devices: 
    >> Host: scsi0 Channel: 00 Id: 06 Lun: 00
    >> Vendor: IOMEGA   Model: ZIP 100          Rev: D.17
    >> Type:   Direct-Access                    ANSI SCSI revision: 02
    >> Host: scsi1 Channel: 00 Id: 01 Lun: 00
    >> Vendor:          Model: Scanner          Rev: 1.40
    >> Type:   Scanner                          ANSI SCSI revision: 04
    >> Host: scsi1 Channel: 00 Id: 01 Lun: 01
    >> Vendor:          Model: Scanner          Rev: 1.40
    >> Type:   Scanner                          ANSI SCSI revision: 04
    >> Host: scsi1 Channel: 00 Id: 01 Lun: 02
    >> Vendor:          Model: Scanner          Rev: 1.40
    >> Type:   Scanner                          ANSI SCSI revision: 04
    >> Host: scsi1 Channel: 00 Id: 01 Lun: 03
    >> Vendor:          Model: Scanner          Rev: 1.40
    >> Type:   Scanner                          ANSI SCSI revision: 04
    >> Host: scsi1 Channel: 00 Id: 01 Lun: 04
    >> Vendor:          Model: Scanner          Rev: 1.40
    >> Type:   Scanner                          ANSI SCSI revision: 04
    >> Host: scsi1 Channel: 00 Id: 01 Lun: 05
    >> Vendor:          Model: Scanner          Rev: 1.40
    >> Type:   Scanner                          ANSI SCSI revision: 04
    >> Host: scsi1 Channel: 00 Id: 01 Lun: 06
    >> Vendor:          Model: Scanner          Rev: 1.40
    >> Type:   Scanner                          ANSI SCSI revision: 04
    >> Host: scsi1 Channel: 00 Id: 01 Lun: 07
    >> Vendor:          Model: Scanner          Rev: 1.40
    >> Type:   Scanner                          ANSI SCSI revision: 04
    >> =========================================
    >> Cheers
    >> Johan Wehtje
    >> 
    >> _______________________________________________
    >> Sane-devel mailing list
    >> Sane-devel at www.mostang.com
    >> http://www.mostang.com/mailman/listinfo/sane-devel
    cn> _______________________________________________
    cn> Sane-devel mailing list
    cn> Sane-devel at www.mostang.com
    cn> http://www.mostang.com/mailman/listinfo/sane-devel

-- 
Ray Curtis
mailto:ray at ccux.com                           http://www.ccux.com